Need Help?
Call
This black plastic drip tray mounts beneath the water and ice dispenser on the front of the refrigerator door. It catches overflow water, ice chips, and drips to keep the floor clean. Replace it if the tray is cracked, warped, discolored, or no longer snaps securely into position.
Ordered the parts. Watched a great video on this web site. Installed. Fixed. Easy peesey. Read more
Connects the dispenser motor to the ice bucket auger. Replace if stripped, worn, or broken to restore proper torque transfer and smooth ice dispensing.
Removed drip pan from ice dispenser. Removed two screws hidden behind drip pan to loosen bezel at bottom. Carefully lifted bezel off top hook to expose controller board cabling. Disconnected three connectors to control board behind bezel to remove bezel completely. Removed two (possibly three) screws to access the back of the ice chute mechanism. Removed broken paddle that just snaps in, being careful to capture paddle spring. Put paddle spring on new paddle and maneuvered spring-end... Read more
Replaces a cracked, worn, or unresponsive dispenser pad on your refrigerator door. Installs in the front dispenser housing for water and ice.
Removed water catcher, then 4 screws in water/ice vault in door, then removed screws on door side (5) top (2) and bottom (2). Removed stainless door skin. Removed 4 hex head bolts in ice/water vault (containing pads) and 4 bolts on the module immediately above the vault. Pulled the vault and module above out part way to unplug one cable. Then laid on table to unplug pads. From back, each pad has a small indent preventing the pad from being pushed up and removed. Push the small indent with a... Read more
Replacement actuator pad for refrigerator water and ice dispensers. Snaps into dispenser panel. Replace if cracked, broken, or tabs are damaged.
Super easy fix, remove two screws behind drop tray, unplug the wiring harness to dispenser, unplug and remove old pad, then snap new one into place. Reconnect harness. Took less than 5 minutes, works like new. Read more
Replaces the lighted paddle you press to dispense water or ice from your refrigerator door. Restores activation when the original pad is cracked, worn, or missing.
Replace the part and working good. Read more
Replacement drip tray for refrigerator water and ice dispenser. Installs below dispenser opening. Replace if cracked, warped, discolored, or missing.
After using the crushed ice feature on my KitchenAid French Door refrigerator, the ice maker wouldn't stop dispensing ice, crushed or cubed. I thought it had to do with the paddle switch being stuck or something else in the door, but all door components seemed to be working as intended. I ended up pulling the ice maker out and disconnecting the wires to the auger so that I could leave the refrigerator plugged in. I call AppliancePartsPros.com the following morning and explained my situation.... Read more
This is a black plastic drip tray that sits beneath the water and ice dispenser on the front of the refrigerator. It catches overflow water and ice that miss the glass, preventing spills on the floor. Replace this tray if it is cracked, warped, discolored, or no longer snaps securely into place.
Ordered the parts and simply fit them in place. Read more
This is the actuator pad located on the front of the refrigerator's water or ice dispenser area. It serves as the pushpad that you press with your glass to activate the water or ice dispensing mechanism. Replace this part if the pad is cracked, broken, or no longer triggers the dispenser when pressed.
Repairman said I'd need to replace the entire chute inside at a cost of nearly $400! Ordered the chute myself for a little over $100. Took me about a half an hour to carefully disassemble the water/ice dispenser and replace with the new one. The job wasn't hard, I'm just not a very "handy" guy but I love a good challenge and am very careful not to pull and pry on things which may break. It was literally only 4 screws that had to be removed and some wiring harnesses holding everything together.... Read more
Black grille that sits at the base of your refrigerator's ice/water dispenser to catch drips. Replace when cracked, stained, loose, or missing.
Bought a replacement overflow grille. Read more
Color: Midnight Grey
Ordered the part. It came in pretty quick and was an exact match. Googled the instructions, followed them step by step. The only thing I did different was I marked the wires so I could put them back right. Took around an hour to replace. Wasn't difficult at all. Read more
Stainless steel grille that sits on your refrigerator's dispenser drip tray. Replace if cracked, broken, or missing to restore a finished look.
Covers and protects the ice container in your refrigerator. Replace if cracked, broken, or missing to keep ice fresh and prevent contamination.
White plastic grille that sits beneath the ice and water dispenser to catch drips and spills. Replace if cracked, stained, or missing for a clean look.
The new Ui assembly that has all new push buttons. I found the water shutoff and the power plug when we pulled the fridge out. I shut off the water and pulled the AC plug. The whole assembly that is being replaced, came out easily when I pushed two small tabs on the lower part of the old asm bottom left and right. I used a small screwdriver to release one and then the other tab. I disconnected the electrical connector and the old unit was free. Connect the power plug to the new unit and slide... Read more
Channels ice from maker to dispenser opening. Replace if cracked, broken, or missing to prevent ice scatter and jams. Installs in freezer door dispenser.
Identified and ordered part Read more
White overflow grille for refrigerator water/ice dispenser. Replaces cracked, pitted, discolored, or missing grilles. Snaps into place below dispenser.
I found the part I needed through AppliancePartsPros.com. The price was far more than I wanted to spend, but my wife kept asking me to get a replacement. "Any port in a storm" as the old saying goes. I'm keeping it clean for the time being. When company comes over, I'll put it in to make the refrigerator look good. Read more
Color: black. Measures about 10 inches wide by 4 inches deep.
I replaced the water inlet valve & both dispenser levers (water & ice) and adjusted the lever locking spring. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.