Need Help?
Call
Bypass cap replaces water filter when filtration isn't needed. Install when using RO system or preferring unfiltered water. Confirm fit with your model.
Water dispenser came down to a trickle and made a lot of noise, I changed the filter but it didnt help and thus the water tank/head assembly needed to be replaced. Replacing the water Tank/head assembly was an easy task, the hardest part is removing the covers and taking care of not breaking the insulation of the water inlet hose. For the not-so-experts like me it is also good to rememebr to have a bucket to collect all the water that comes out after the connection to the solenoid valves is... Read more
Secures water filter for proper filtration and flow to dispenser or ice maker. Replace if cracked, leaking, or filter won't seat properly. Verify fit.
Replaced the old housing with new water filter housing. Read more
Houses and protects your refrigerator's water filter. Replace if cracked, leaking, or seals are worn to prevent water damage and maintain water quality.
Replaced water filter housing Read more
Encloses the water filter to ensure proper flow and filtration. Replace if cracked, leaking when filter is removed, or causing water hammer. Confirm fit.
The video was very helpful, but my KitchenAid model required slightly more steps. Only the two screws in front held the filter housing, same as the video shows, but it has to be removed from the rear. My model did not have the wire brace, only the two front screws held the housing. Shut the water off and pull the electrical plug. Remove the two screws holding the filter housing in the front. Remove the lower panel in the rear at the bottom of the refrigerator. Remove the two screws holding the... Read more
Holds the water filter and routes water to the dispenser and ice maker. Replace if cracked, leaking, or won't engage the filter. Confirm fit by model.
Replaced housing. That was simple but finding directions in how it I remove top of cabinet was time consuming. After two hours of searching I finally found one article that explained why there were no screws to remove. Read more
Reduces contaminants like chlorine and lead for clean drinking water and ice. Replace every 6 months for optimal performance. Confirm fit with model.
Ordered a new one Read more
Secures the water filter and maintains watertight seals to prevent leaks. Replace if cracked or leaking at tube connections to restore water flow.
It's bit of a chore in that on my Whirlpool Refrig you need to remove the grill on bottom front and the Utility Panel on bottom rear. Then unscrew the original filter housing and pull it out through the back of utility opening. Remove the two water hoses and put them into new filter house. Reverse the disassembly process to reinstall new filter housing. I'm old and slow so the process took me about 45 minutes. (Note: Unplug electric and turn off water inlet before starting.) Read more
Grease filter for range hoods and over-the-range microwaves. Dimensions: 6-1/2" x 12-3/16" x 3/32" (6.5 x 12.1875 x 0.09375). Rectangle shape. Captures grease from cooking air. Replace when clogged, discolored, or every 6-12 months.
I started by watching the video posted by couple of people on youtube on how to replace a microwave handle. After taking out the liner, I hit a roadblock with unscrewing the handle screw. The grip on the front side had basically melted causing it to be loose, so the screw and the plastic part would rotate together. After trying several things, I gave up and took it to Ace hardware to find an extractor of some sort. Luckily, the guys there used several tools and managed to get the screw out.... Read more
Traps grease particles to prevent buildup on blower and internal components. Replace when clogged or discolored. Verify fit with your model number.
I was just replacing my filter,on my vent. Read more
Holds the filter cartridge and seals water lines to your dispenser and ice maker. Replace if cracked or leaking to restore proper flow. Confirm fit by model.
Disconnect the housing carefully from water line (push and release) and replace with new parts Read more
Holds filter cartridge and routes water to dispenser and ice maker. Replace if cracked or leaking to restore proper seal and water flow. Confirm fit.
Replaced water filter housing. Read more
This is a small mesh filter screen that fits inside the water inlet valve to catch sediment and debris from your household water supply before it enters the washer. It prevents mineral buildup and particles from clogging or damaging the valve internals. Replace this screen if your washer is filling slowly, not filling at all, or if the screen is visibly clogged, torn, or deteriorated.
Went on internet, found a great site and learned that the cold water hose filter was very much clogged at the machine intake. Cleaned it and voila. Ordered an extra filter from Appliance Pros.com and literally was amazed that it arrive within 2 days of my internet order. Great efficiency and customer service….great experience. Will definitely use them in the future….thank you! Read more
Carbon filter for range hoods and over-the-range microwaves. Dimensions: 5-5/8" x 11-9/16" x 3/8" (5.625 x 11.5625 x 0.375). Rectangle shape. Removes cooking odors from cooking air. Replace when clogged, discolored, or every 6-12 months.
Replaced it. Read more
Grease filter for range hoods and over-the-range microwaves. Dimensions: 5-5/8" x 11-5/8" x 3/32" (5.625 x 11.625 x 0.09375). Rectangle shape. Captures grease from cooking air. Replace when clogged, discolored, or every 6-12 months.
Grease and odor filter with integrated light lens for range hoods and over-the-range microwaves. Dimensions: 11-7/16" x 11-13/16" x 3/8" (11.4375 x 11.8125 x 0.375). Rectangle shape. Captures grease and removes cooking odors from cooking air. Replace when clogged, discolored, or every 6-12 months.
I found what I needed fairly quickly. Before coming here I was having trouble. The part came quickly and fit perfectly. Read more
Secures the filter cartridge and channels water through your refrigerator. Replace if cracked, leaking, or causing dispensing issues. Confirm fit by model.
Tried several new filters. Finally replacing housing fixed problem. Could not find any obvious defect in the housing, however, when pushing real hard on the filter door,water would flow.Seems to be some transfer valve inside housing body not properly actuated. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.