Whirlpool Wall Oven Switch

I was able to clean the Oven Temp Sensor with 99% alcohol. Then replaced All switches (after breaker was isolated). Put it all back the way I found it. Turned on breaker. Tested all functions and had no reports of Fan Code re-appearing since. Read more

I called a rpair service. The men came to the house, torn apart the stove top and advised Replacement of the wire harness. The trip charge of $100 would be deducted from a repair bill of $350, thus they needed an additional $150 for parts and $100 for labor after paying the trip charge. I bought the harness for $60, and the star bits I needed for my drill for $10. My son and I installed the new harness in about 30 minutes, which included a thorough cleanup, saving us $180. Read more

• Element will not heat

This cooktop has a dual element with an inner burner surrounded by an outer burner. The switch controls either the inner burner alone or both. The switch failed in that it would not operate the inner burner by itself, both burners would come on and only on high. On 8/14/2014 I replaced the failed dual element switch as follows: • Turned power off to cooktop. • Removed unit from cabinet. • Removed metal edging and glass top. • Removed screws holding switch panel access underside. • Removed old... Read more

Replace switch Read more

Replaced the Spark Module and the Wire Harness. Works like new. Read more

Had to replace both switches. The hard part was getting the control panel off to get access. Only a few screws but even after getting them out, really struggled getting it off. After getting off, discovered that you need to get it lifted up before pulling it off. Read more

I watched an 8-minute video on YouTube. Identified and ordered the part from AppliancePartsPros that a $12 shipping fee was received in 2 days. Took 10 minutes or less to install. Years ago without next-day parts and YouTube, this $60 repair would have cost me $200+. Read more

Trial and error only cooktop unit. Everything mounted into the counter and needed to pull unit out. I figured it was a control switch or the burner itself. Based on costs, I took the less expensive route and replaced the 2 known malfunctioning switches. All on-line videos said it was a 2-3 hour process to replace. I finished mine in less than 30 minutes. Turned breaker back on and it works like a charm. 30 years old and still going strong. Read more

• Won't start

By replacing the switch, the front right burner correctly turned on the igniter and worked. Repair took about 5 minutes. Very easy to do. Read more

Went on line to find the part number. Once I had the number I searched for the part. Found it, had it shipped overnight and installed it with the help of a video from youtube. Read more

Turn the power off to the range. Pull off the black control knob. Remove 6 - 5/16 screws in back of the range behind the controls panel. Take out 2 screws (behind the control knob) in front that hold the control swirch in the panel. Remove each wire from the old switch and place it onto the new switch (one at a time)so get the wires are installed in the correct place. Make sure the wire are tight on the new switch. Install the new switch, put the two mounting screws in, reinstall the back, put... Read more

Ordered a new switch (4456027) from you. You seemed to have the best price and guaranteed that it was a OEM part -not everybody did. I had repaired Jenn Air cook tops before so I thought this was not a problem. Wrong. Mostly it was my own stupidity. I exchanged the wires from the old switch to the new one at a time but did write down where the original wires went. Flipped the breakers back on. Only one heater got hot. Searched the internet for several days for a wiring diagram. Nothing much.... Read more

Ordered new igniter, a little different from the original but fortunately was able to get it to operate ok with a little bit of modification ?? Read more

Removed rocker switch,made up jumper so the compactor could be used while awaiting replacement switch. The part came 2 days later and was installed in less tha 5 minutes. Unit working like new again. Thanks for the great service!! Read more