Whirlpool Washer Switch

This auto load sensing water level pressure switch monitors the tub's water level via the air hose and signals the control to start or stop filling. It helps prevent underfilling or overfilling for consistent wash performance. What it does:

• Senses tub water level through air pressure and communicates with the control/timer
• Regulates automatic load-size fill by cycling the inlet valve circuit
• Addresses symptoms such as won't fill, won't stop filling/overfills, underfills, or cycle not advancing due to water-level detection issues

• One load-sensing water level pressure switch

• Disconnect power and shut off water supply before servicing
• Access the console/top to release and remove the switch
• Transfer wire connectors and the pressure hose one at a time; ensure the hose is seated fully and not cracked, kinked, or obstructed
• Do not adjust any calibration screws; mount in the same orientation and reassemble

This lid switch detects when the washer lid is closed and signals the control to allow motor operation. Replacing a faulty switch restores normal cycle starts and the washer's safety interlock. What it does:

• Detects lid position and completes the electrical circuit so the washer can start and run.
• Acts as the safety interlock that prevents the motor from running with the lid open.
• A failing switch can prevent the washer from starting, stop spin or agitation, or cause cycles to stop unexpectedly.
• Replaces the lid-actuated switch used in top-load washers' control/interlock system.

• Disconnect power at the breaker or unplug the appliance before beginning work.
• May require removing the washer top or control panel to access the switch—keep track of fasteners and connectors.
• Handle electrical connectors gently and verify connections are secure; test the new switch only after restoring power per manufacturer guidance.

The Dispenser Switch is an OEM component for Whirlpool washing machines. Located inside the detergent compartment, it detects when the door is properly closed to enable cycle functions.   

The sensitive switch utilizes durable contacts to reliably connect without false readings due to vibration. Its secure plastic housing contains electronic components regulating additive distribution during selected cycles.

Symptoms of a bad dispenser switch can include:

• Inability to start cycles despite closed door
• Dispenser door fails to lock properly   
• Fault codes relating to dispenser issues  
• Cycles unexpectedly terminating mid-load

Replace yours today with this genuine Whirlpool switch to ensure detergent and other additives activate at optimal times for thorough, even cleaning. Compatible with Kenmore, Maytag, and some Jenn-Air washers.

This water level pressure switch senses the washer's water level and tells the control when to stop filling, helping restore correct fill cycles and prevent overfilling or underfilling. Fits many top- and front-load Whirlpool machines. What it does:

• Monitors tub water pressure and signals the washer control to start/stop filling.
• Can resolve symptoms like overfilling, no fill, always filling, or washer not advancing through cycles.
• Works as the control's water-level detector, replacing a failed or intermittent switch.
• Compatible with systems that use a pressure hose to communicate tub water level.

• One water level pressure switch (pressure sensor) as shown.

• Disconnect power and turn off water supply before starting any repair.
• Access typically requires removing the control console or top panel; handle internal wiring and connectors carefully.
• Reconnect the pressure hose securely to avoid false readings; inspect hose for cracks or blockages and replace if needed.
• Test the washer through a quick cycle after installation to ensure correct operation.

This water level pressure switch senses drum water level and tells the washer when to stop filling so loads get the correct amount of water. It restores reliable fill control for machines that overfill, underfill, or fail to advance cycles. What it does:

• Monitors water height via an air-pressure line and signals the control board to start or stop filling.
• Helps prevent overfilling or underfilling that can cause poor wash performance or leaks.
• Can restore normal cycle advance when a faulty level switch causes the washer to stall or display fill/drain errors.
• Works as the washer's primary water-level detection device tied to automatic fill control.

• One water level pressure switch assembly

• Disconnect power and water supply before attempting service.
• Handle wiring connectors and the pressure hose gently; secure connections to avoid air leaks.
• Verify proper routing and attachment of the pressure hose to ensure accurate level sensing.

This cycle selector switch is the user control that selects and advances cooking/drying cycles, restoring reliable cycle selection and user control on compatible appliances. It provides a direct replacement for a worn or non-responsive selector. What it does:

• Rotates to select the appliance cycle and sends the chosen setting to the control system
• Restores proper cycle selection when the knob or control no longer changes settings
• Commonly used when cycles won't start, don't advance, or the control feels loose or intermittent
• Works as the mechanical/electrical interface between the user knob and the appliance control

• Disconnect power to the appliance before beginning any work
• Remove the control knob and panel trim to access the switch—keep track of screws and small parts
• Note or label wire locations before disconnecting; reconnect wires to the same terminals
• Test cycle selection and appliance operation after installation; if issues remain, check related controls and wiring

This cycle selector switch lets the user choose wash or dry cycles by turning the control dial. It restores reliable cycle selection and responsive dial behavior so the machine starts the intended program. What it does:

• Selects the appliance cycle position when the control knob is turned
• Sends the chosen cycle signal to the timer/control assembly
• Commonly replaced when the dial slips, feels loose, or won't advance between cycle positions
• Helps resolve issues where the machine won't start the selected cycle or changes settings unexpectedly

• Disconnect power (and water if a washer) before servicing
• Access typically requires removing the control console or panel; follow your model service manual
• Avoid bending terminals; match connector orientation during reassembly