Whirlpool Washer Switch

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling

2 position. Extra rinse.

Color: Black. Instruction sheet included.

This water level pressure switch monitors the tub's water level via an air hose and signals the washer when to stop filling and move to the next step. Replacing a failed switch restores accurate fills and reliable cycle operation.

• Senses tub water level through air pressure and communicates with the timer/control
• Shuts off inlet valves at the correct level to help prevent overfilling
• Allows the cycle to advance to wash, drain, and spin based on sensed level
• Common symptoms: overfilling/overflow, underfilling or no fill, cycle stuck at fill/sensing, no agitate or spin

• Disconnect power and turn off water supply before servicing
• Access the control console to remove the old switch; note wire locations for correct transfer
• Move the air hose to the new switch and ensure the hose is clear, undamaged, and snug at both ends
• Reassemble and run a test fill to verify proper shutoff and cycle progression

This pushbutton switch restores reliable on/off control for a specific function on your appliance. When the original switch wears out, the button may stop responding, work intermittently, or stick when pressed.

• Provides an electrical on/off signal to the control or component when the button is pressed
• Typical symptoms include no response when pressed, intermittent operation, or needing to hold the button to activate
• Physical signs can include a broken/sticking button or discolored/loose terminals
• Replacing the switch restores normal button feel and consistent operation

• Disconnect power from the appliance before servicing
• Access the control area to reach the switch and note its orientation
• Label and transfer wires one at a time; ensure snug spade connections without bending terminals
• Test operation before reassembling panels

Restore precise cycle selection with this rotary encoder cycle switch. Mounted behind the control knob, it sends your chosen setting to the washer's control, resolving unresponsive or erratic knob behavior so the correct cycle and indicators engage.

• Translates knob rotation into signals the main control uses to select a wash cycle
• Helps ensure the selected cycle registers accurately on the user interface
• Wear or internal faults may cause an unresponsive or erratic cycle knob
• May also lead to incorrect indicator lights, intermittent selection, or a no-start condition

• Disconnect power before servicing
• Pull the knob straight off; open the console to access the encoder
• Release locking tabs and transfer wiring one connector at a time; align the keyed shaft
• Reassemble and verify the indicators respond to knob rotation before running a load

This water level pressure switch senses the tub's water level via air pressure and signals the control to stop filling at the correct point, helping the cycle advance properly and guarding against overfilling.

• Monitors water level through the pressure hose and reports to the control
• Shuts off inlet valves when the target level is reached
• Allows the cycle to proceed and spin only when the tub is sensed empty
• Common symptoms of a failed switch include overfilling or underfilling, long fill, stopping during fill, not advancing, or water-level error codes

• Disconnect power and turn off water supplies before servicing
• Access the console/control area; move the wire harness and pressure hose to the new switch and secure it in place
• Inspect the pressure hose for kinks, cracks, or moisture; clear or replace if damaged to ensure accurate sensing
• Ensure an airtight hose connection, then run a test fill to verify proper shutoff and operation

This rotary on/off switch controls the dryer's Finish Guard (also called Wrinkle Guard/Wrinkle Shield) feature. Replacing it restores proper control of the post-cycle intermittent tumbling that helps reduce wrinkles, preventing the feature from being stuck on or off.

• Provides 2-position on/off selection for the Finish Guard/Wrinkle Guard function
• Failure can cause the feature not to engage or to stay on after the cycle ends
• Knob may feel loose or fail to click when the switch is worn
• Mounts in the control console and interfaces with the external selector knob

• Disconnect power before servicing
• Access through the control console; remove paneling as needed
• Transfer wires one at a time or photograph connections for reference
• Reinstall using the existing knob and mounting hardware

This Smart ATC temperature switch senses and helps regulate oven temperature for more consistent cooking. It replaces a failed switch to restore correct temperature feedback to the range control for accurate heating. What it does:

• Detects oven temperature and sends a signal to the control so heating elements cycle appropriately
• Helps correct issues where the oven runs too hot, too cold, or cycles erratically
• Works as part of the temperature control system—does not include the main control board
• Replaces a worn or failed temperature/A.T.C. sensor switch to restore proper temperature sensing

• One temperature switch (Smart ATC)

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Access typically requires removing the oven control panel or back panel; keep track of screws and wire connections
• Handle the switch and connector gently to avoid damage; verify wiring matches original before reconnecting

This water level pressure switch senses the washer tub's water height and signals the control to stop filling. Replaces a failed level sensor to help restore proper fill control and prevent incorrect water amounts. What it does:

• Monitors air pressure from the tub to detect water level and tells the control when to stop or continue filling
• Can cause symptoms such as incorrect fill levels, overfilling, underfilling, or interrupted cycles when faulty
• Works with the washer's control system to ensure cycles progress only when the correct water level is reached
• Requires checking the air hose and connections when diagnosing related issues

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Shut off the water supply and remove the necessary access panels to reach the switch
• Handle the switch and wiring carefully; note connector positions and routing of the air hose for correct reinstallation
• After installation, run a short test cycle and inspect the air hose for secure, leak-free connections

This pushbutton switch restores a single button on the appliance control panel so you can reliably send selection or command inputs to the control board. It replaces a worn, stuck or non-responsive panel button. What it does

• Acts as the user-facing pushbutton that completes the control input circuit when pressed
• Sends selection/command signals to the appliance control board or timer
• Common symptom fixer: button that won't register presses or responds intermittently
• Also used when a button is physically stuck, loose, or missing

• Disconnect power to the appliance before beginning service to avoid shock
• Access typically requires removing the control panel or overlay—retain screws and trim
• Verify connector orientation and seating; do not force connectors or terminals

This water level switch detects the washer's water height and signals the control to start and stop filling, helping maintain proper wash cycles and prevent overfilling. What it does:

• Senses water level via a pressure hose and tells the control when to stop filling.
• Can cause continuous filling, overfilling, or failure to advance cycles when faulty.
• Works with the washer's control board and pressure hose to regulate fill actions.
• Intermittent or no fill/no water level detection are common symptoms of failure.

• Disconnect power and water supply before beginning any repair.
• Carefully detach the pressure hose from the switch; replace with correct routing to avoid kinks.
• Inspect and replace a cracked or clogged pressure hose when present; verify hose connection is airtight.
• Test switch continuity with a multimeter per service instructions; refer to the service manual for wiring and diagnostic steps.