Need Help?
Call or text
Show parts
Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.
Mounting screw for refrigerator interior components like fan brackets, ice maker assemblies, and shelving. Replace if stripped, missing, or corroded.
Replaces a cracked, severed, or frozen ice maker fill tube and grommet. Delivers water from valve to ice maker. Includes tube, grommet, and plate.
Secures the auger shaft in the icemaker assembly. Replace if stripped, cracked, or loose, preventing proper ice transport from bin to dispenser.
Includes 12 retainer rings.
Protective enclosure for the ice crusher mechanism in your refrigerator's dispenser. Replace if cracked, broken, or damaged from ice jams or wear.
Includes 12 washers.
Usually ships within 4 - 14 days
Replacement pivot that supports and aligns refrigerator doors or drawers. Needed when original pivot is cracked, broken, or worn, causing misalignment.
This part is discontinued by the manufacturer and is no longer available for purchase.
Ice scattering everywhere? This deflector guides cubes or crushed ice down the chute into your glass. Replaces cracked or missing deflectors in 30 minutes.
Wire actuator for refrigerator dispenser mechanism. Connects dispenser lever to electrical circuit. Replace if bent, broken, or detached to restore lever.
The Ice Deflector Spring is an OEM replacement part for GE refrigerators. This spring is a crucial component of the ice dispensing system, specifically in selecting between crushed and whole ice cubes. It is designed to always force the diverter back i
Metal retainer spring secures trim panels and lightweight components in your refrigerator. Replace when worn, broken, or missing to restore snug fit.
Ice won't crush in your refrigerator? These auger blades move ice through the crushing mechanism. Common fix when crushed ice dispenses as cubes.
Fix ice dispenser jamming or not crushing ice with replacement auger blades. Common fix for ice crushing problems in side-by-side refrigerators.
Ice not crushing or dispensing properly? This refrigerator ice crusher auger blade assembly moves ice through the dispenser. Common DIY fix.
Mounting spacer maintains proper clearance between refrigerator panels, doors, or components. Replace if cracked, broken, or missing to restore fit.
Washer for refrigerator crusher blade assembly. Replaces cracked, worn, or missing washers in ice dispenser mechanism. Restores secure mounting.
Ice dispensing wrong type or jammed? This stationary blade assembly secures the blade for smooth ice crushing. Simple repair restores proper function.
Ice dispenser not working or crushed ice won't dispense? This crusher cover protects the ice crushing mechanism. Easy DIY repair with step-by-step video.
Ice dispenser not working or auger broken? This ice bucket auger moves ice from storage to the dispenser chute. DIY repair in 30-45 minutes with video.
Ice won't dispense from your refrigerator door? A cracked bucket or broken auger is often the cause. This assembly restores ice dispensing function.
This silicon controlled rectifier (SCR) is an electronic switching device used to control power to oven/stove heating circuits, helping the appliance regulate temperature and heat output for cooking performance. What it does:
Replaces a cracked, broken, or missing right-side glide bucket on your refrigerator door. Secures storage bins and allows smooth sliding on the rail.
The Glide Bracket is an OEM part for GE refrigerators. This left bracket supports the refrigerator drawer, allowing it to slide in and out smoothly for easy access to stored items.
Causes of a bad glide bracket can include regular wear and tear
This small guide sits at the icemaker fill area and manages the water stream. It directs incoming water into the fill cup and channels any excess safely away to help prevent splashing, leaks, and ice buildup inside the freezer.
Angle bracket for refrigerator internal mounting. Secures components in place. Replace if bent, broken, or missing to restore proper support and alignment.
Ice won't dispense or auger spins freely? The drive coupler connects the motor to the auger. Moderately easy DIY repair with pliers and patience.
Mounting screw fastens panels, brackets, and trim in refrigerators, dishwashers, and ranges. Replace missing, stripped, or rusty screws to secure parts.
Fix ice dispenser not crushing or dispensing ice with this refrigerator ice crusher motor. Direct replacement for GE and other brands. Moderate DIY repair.
10-18 hex washer screw for securing panels, trim, brackets, and components in appliances. Replaces lost, stripped, or corroded fasteners.
Wire harness assembly that connects the motor and solenoid in your refrigerator. Replace if wires are frayed, connectors are damaged, or harness is broken.
This solenoid saddle is a small mounting bracket that secures a refrigerator solenoid in the correct position. By preventing movement and misalignment, it helps the linked mechanism engage smoothly and consistently.
Fix a refrigerator that won't dispense water or make ice with this water inlet valve solenoid assembly. Direct replacement part for select models.
This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.
Ice dispenser only making crushed ice instead of cubes? This solenoid valve kit fixes the cube/crushed ice selector. Easy DIY repair with video guide.
Replaces a cracked or broken ice auger motor boot housing in your refrigerator's dispenser. Installs inside the ice bin to enclose the auger motor assembly.
Replaces damaged or cracked trim over your refrigerator dispenser. Restores clean appearance and hides internal components. Direct fit for dispenser opening.
This is a 220v international model icemaker.
Channels water from the fill tube into the icemaker mold. Replace if cracked, broken, or dislodged, causing water leakage or ice buildup in freezer.