Bosch Parts

This black replacement door handle restores a dishwasher's exterior grip and appearance, letting the door open and close securely. It matches factory fit and finish for compatible Bosch dishwasher models. What it does:

• Replaces a cracked, broken or missing door handle to restore normal door opening
• Provides a solid grip for pulling the dishwasher door open and closed
• Restores the appliance's exterior appearance when the original handle is damaged
• Fits the factory handle mounting locations and aligns with the door trim

• One black door handle

• Disconnect power to the dishwasher before starting any repair
• Support the door while removing fasteners to prevent it from closing unexpectedly
• Remove interior door panel or trim as required to access handle screws or clips
• Use manufacturer service manual or OEM instructions for step-by-step removal and reassembly

This sump clamp secures the dishwasher sump/drain assembly to the tub, keeping the seal and pump assembly held in place to prevent leaks and movement. It's a small but essential fastener for a watertight sump connection. What it does:

• Holds the sump/drain housing tightly against the tub to maintain a proper seal
• Prevents the sump assembly from shifting during operation, which can cause leaks or noise
• Helps stop water from leaking under the machine when the pump runs
• Supports proper alignment of the drain/pump components for reliable draining

• One sump clamp

• Disconnect power and water supply before starting any repair
• Access the sump area by removing the lower access panel or toe kick and tilting the machine as needed
• Inspect the sump seal/gasket and replace if cracked or damaged when replacing the clamp
• Tighten clip until secure but avoid forcing or deforming the sump housing; test for leaks after reassembly

This actuator lever assembly with springs replaces a worn or broken control lever to restore proper mechanical movement in the appliance. It helps the dispenser/latch mechanism operate smoothly for reliable everyday use. What it does:

• Transfers motion from a control cam or motor to the latch or dispenser linkage
• Restores proper engagement when a broken or fatigued lever prevents operation
• Helps stop intermittent or failed cycle starts caused by damaged mechanical linkage
• Works as a direct-fit replacement that re-establishes spring tension and lever action

• Disconnect power before accessing internal components to avoid shock or injury
• Basic hand tools usually required; maintain original screw/hardware if reusing
• Inspect surrounding linkages and replace damaged clips or fasteners as needed

This door latch cover is the exterior trim that fits over the dishwasher door latch, restoring a finished appearance and protecting the latch mechanism from spills and wear. It matches stainless-steel finishes and keeps the latch area clean. What it does:

• Covers and protects the door latch assembly from moisture and grime.
• Restores the dishwasher door's exterior appearance when dented, scratched, or missing trim.
• Helps prevent debris build-up that can interfere with latch engagement.
• Compatible with latch installations that use a snap-on or screw-attached cover.

• Remove power to the appliance before starting any repair to avoid electrical hazard.
• Remove the inner door panel or access trim per service instructions to reach latch area.
• Install by aligning the cover over the latch and securing with the original screws or clips; do not force or bend the cover.
• If metal damage or latch misalignment is present, inspect latch mechanism and replace if necessary.

A small spring-style hose clamp used to secure flexible appliance hoses to fittings and prevent leaks. Simple, durable replacement that restores a tight connection for water and drain lines. What it does:

• Compresses around a hose to hold it firmly on an inlet, outlet or drain fitting
• Helps stop leaks caused by loose or slipping hoses
• Keeps hoses seated during normal appliance operation and vibration
• Commonly used on dishwasher and washer drain or water hoses

• One hose clip / spring clamp

• Disconnect power and water supply before starting repairs
• Use pliers to expand the clamp for removal and reinstall; ensure hose is fully seated before releasing clamp
• Inspect the hose and fitting for damage; replace any cracked or brittle hose
• Do not overtighten or deform clamp when installing; replace if corroded or weakened

A 15 amp cartridge fuse that protects appliance electrical circuits from overcurrent, helping prevent damage to controls and components. Fits into inline fuse holders or boards where that specific fuse rating is required. What it does

• Interrupts circuit power when current exceeds 15 amps to protect wiring and electronics
• Commonly linked to symptoms like no power to controls, unresponsive display, or appliances that won't start
• Designed to be replaced when visibly blown or when continuity test fails
• Works as the exact rated safety fuse specified for compatible appliances

• One 15 amp cartridge fuse

• Disconnect all power to the appliance before accessing or replacing the fuse
• Replace with the identical fuse type and 15 amp rating only; do not substitute different ratings
• Handle carefully and mount fully seated in its holder or on the PCB as designed
• If the new fuse fails again immediately, stop — repeated failures indicate underlying electrical faults

This stainless steel cooktop control knob replaces a worn or damaged selector on electric Bosch cooktops, restoring a solid grip and accurate temperature control. Designed to match factory fit and appearance for a clean, functional finish. What it does:

• Replaces a damaged, faded, or loose control knob so you can safely select burner settings
• Provides a clear tactile stop for reliable temperature selection
• Restores the original appearance of the cooktop surface
• Helps prevent accidental knob movement caused by worn parts

• Turn power to the appliance off at the breaker before servicing to avoid electrical hazard.
• Pull off the old knob straight away from the shaft; align the new knob with the shaft and press on until fully seated.
• If the knob does not fit, verify shaft type and part number before forcing.

This carafe glass insert replaces a damaged or leaking coffee carafe glass and restores a safe, visible vessel for brewed coffee. The included gasket helps form a leak-resistant seal so the carafe functions as intended. What it does

• Holds brewed coffee and provides clear visibility of liquid level.
• Gasket helps seal the insert to prevent drips and leaks during pouring.
• Replaces cracked, chipped or shattered glass that can cause leaks or safety hazards.
• Restores safe use when the original carafe glass has visible damage.

• Allow the appliance and carafe to cool completely before handling broken glass.
• Handle glass carefully and wear gloves to avoid cuts when removing a broken insert.
• Clean mating surfaces and seat the gasket fully to ensure a proper seal before use.
• Hand wash the glass insert; inspect gasket for proper fit and damage before reinstalling.

This retaining clip secures small appliance components in place to prevent movement and ensure reliable part alignment. It provides a simple, durable hold that keeps assemblies stable during normal use and service. What it does:

• Holds panels, covers, or wiring harnesses in position to prevent rubbing or disconnection
• Maintains alignment of moving or attached components to reduce noise and wear
• Helps prevent intermittent electrical or mechanical failures caused by loose parts
• Commonly replaced when broken, cracked, or missing after service or impact

• One retaining clip

• Basic hand tools may be required; inspect surrounding parts before reassembly
• Wear gloves and power off and unplug the appliance before servicing
• Replace only with the correct OEM-designated clip to ensure fit and function

This dishwasher sump assembly houses the pump inlet and integrated ball check valve to route wash water to the drain while preventing backflow. Replaces worn or cracked sumps to restore proper draining and prevent leaks. What it does

• Collects and channels dishwasher wash water from the tub to the drain pump.
• Integrated ball check valve stops backflow into the sump, helping prevent standing water and odor.
• Restores proper drain function when the existing sump is cracked, clogged, or leaking.
• Compatible with common Bosch/BSH dishwasher pump systems that use a molded sump with ball valve.

• One sump with integrated ball check valve (single assembly only).

• Disconnect power and water supply before starting any repair.
• Access typically requires removing the dishwasher lower kickplate and possibly tilting the unit; support the unit and follow the OEM service manual.
• Inspect surrounding seals, hoses, and pump gaskets for wear and replace as needed.

This terminal block is the appliance wiring connector that secures incoming power and links internal circuits, restoring a safe, reliable electrical connection. Replaces a damaged or burned block to help prevent intermittent power or arcing. What it does

• Provides a secure connection point for incoming power leads and internal wiring
• Restores continuity when a cracked, corroded, or burned terminal causes loss of power
• Helps stop arcing, sparking, or overheating at the power entry point
• Used where multiple wires must be joined and fastened to the appliance chassis

• One terminal block

• Disconnect all power before inspecting or replacing the terminal block
• Verify wire locations and take photos or label wires before removal for correct reassembly
• Tighten connections to manufacturer torque spec—do not over-tighten screws
• If you see extensive burn or damaged wiring, replace damaged wires.

This is the left hinge cap. For right hinge cap use 00165295.

This door latch cover is a direct-fit replacement trim piece that protects and conceals the dishwasher door latch assembly while restoring a finished appearance. Keeps the latch area tidy and helps ensure the door closes cleanly. What it does:

• Covers and protects the door latch mechanism from debris and wear
• Helps the door latch engage and the door sit flush when closed
• Restores the appliance's cosmetic finish around the latch area
• Can address symptoms such as a loose-looking latch area or an unsealed door edge

• Disconnect power to the appliance before installing; follow lockout/tagout practices
• Basic hand tools (screwdriver or trim tool) are typically required to remove the old cover
• Align the new cover over the latch assembly and snap or fasten into place per OEM diagram
• If the latch mechanism or strike is damaged, replace those parts as needed for full repair

A reed switch door sensor that detects when the appliance door is closed so the control can start cycles. Replaces a failed magnetic sensor to restore reliable door-closed detection and normal operation. What it does

• Acts as a magnetic contact that signals the control when the door or lid is closed
• Helps prevent the appliance from starting if the door is open or not fully latched
• Common symptom fix for no-start, intermittent cycle start, or control not recognizing a closed door
• Works as the electrical switching element in the door/detector assembly

• One reed switch (single replacement sensor)

• Disconnect power to the appliance before replacing the part to avoid shock or damage
• Handle the switch and wiring gently; avoid bending or stressing terminals and solder joints
• Locate and access the door/detector area per your service manual or tech sheet; confirm connector orientation before installing