Bosch Parts

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

This is an electronic lock mechanism designed for the coin box on commercial-style washing machines. It secures the coin collection compartment to prevent unauthorized access. Replace this lock if the coin box no longer latches properly, the lock mechanism has failed electrically, or the key no longer engages the lock.

Plastic bushing that sits between the washer door hinge and pivot point. Replace when worn, cracked, or causing loose door alignment and noisy operation.

This driveshaft transmits motor torque to the appliance drum so the drum rotates smoothly. Replacing a worn or broken driveshaft helps stop excessive noise, wobble, scraping, or failure-to-spin symptoms. What it does:

• Transfers rotational force from the motor to the drum for normal operation
• Maintains drum alignment; a damaged shaft can cause wobbling or uneven rotation
• Failing shafts may cause loud squeaks, scraping noises, or prevent the drum from spinning
• Works with bearings, couplers and support assemblies—inspect related parts when replacing

• Disconnect power before starting work; follow all safety precautions
• Basic hand tools required; refer to the OEM diagram for disassembly steps
• Inspect and replace worn bearings, seals or couplers as needed to ensure proper operation
• If the shaft is seized or rusted, support the drum to prevent damage during removal

Flexible rubber seal between washer tub and door opening. Replace if you notice leaks, tears, mold, or water dripping during cycles. Confirm fit with model.

Color: stainless. It measures about 3-1/2 inches wide by 6 inches high.

Replacement front cover for dishwasher control module. Needed when plastic is cracked, broken, or switch actuators are worn or missing. Protects control board.

Front control panel fascia that houses and protects buttons and labels. Replace if your fascia is cracked, broken, or worn to restore proper appearance.

White plastic door handle for front-load washer. Provides a secure grip for opening the washer door. Replace if cracked, broken, or loose.

Dishwasher not draining or water pooling at bottom? A cracked sump disrupts water flow to the pump. This housing restores drainage and prevents leaks.

Right side door hinge plate for dishwashers. Secures the door hinge mechanism to the frame. Replace if cracked, broken, or damaged to restore proper fit.

The Impeller Jug is an OEM part for Bosch dishwashers. Located inside the wash chamber, the impeller jug is responsible for evenly distributing water throughout the dish rack during the wash cycle. It features strategically placed holes and channels that work with the spray arms to direct water flow and ensure all dishes receive thorough coverage. 

Symptoms of a bad impeller jug include:

• Incomplete cleaning even on short or heavy wash cycles  
• Dirty dishes remaining at the end of the cycle
• A buildup of food or grime deposits inside the wash chamber
• Off-balanced or excessive noise levels during washing

Causes of failure can be mineral or scale buildup inhibiting water flow, cracked or damaged casing allowing leaks, or worn impeller fins no longer efficiently dispersing water. Over time, hard water deposits and normal use can degrade performance. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers. 

This is the cap that seals the rinse-aid dispenser reservoir on the inside of the dishwasher door. It threads or snaps into place to keep rinse aid contained until it is dispensed during the rinse cycle. Replace this cap if rinse aid leaks out prematurely, the cap is cracked or warped, or dishes are coming out spotted due to improper rinse-aid dispensing.

This plastic cover caps the push button controls on your dishwasher's front panel. Replace if the cap is cracked, missing, or no longer securely covers the button mechanism underneath.

Connects your dryer exhaust to the vent hose for proper airflow. Replace if cracked, broken, or damaged from wear or improper installation.

Fix water leaking into your washer when off or during cycles. This dual inlet valve controls hot and cold water flow. Accessible from the top panel.