Bosch Parts

The Panel Facia is an OEM part for Bosch dishwashers. It is the front control panel of your dishwasher, providing a clean and polished look.

A bad panel facia can occur due to wear and tear over time, accidental damage, or exposure to moisture and cleaning agents. Signs of a faulty facia include cracks, discoloration, or a loose fit that compromises the aesthetic appeal of your dishwasher.

Symptoms of a bad panel facia include:

• Cracks or visible damage on the surface
• Discoloration or fading
• A loose or missing panel

Replace your damaged or worn-out panel facia with this genuine OEM Bosch part to restore the appearance of your dishwasher. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This thermostat with attached sensing cable detects and regulates appliance temperature to help maintain proper heating cycles and protect against overheating. It replaces a failed temperature control component so your appliance can heat correctly and safely. What it does:

• Senses internal temperature and sends a signal to the control to start or stop heating
• Helps prevent overheating by providing accurate temperature feedback
• Works as the temperature-sensing element used by the appliance control board

• Disconnect power before servicing to avoid electric shock
• Handle the sensing cable and probe gently; do not kink or pinch the capillary/sensor
• Verify proper routing and secure mounting of the sensor per the appliance's service instructions

This trim strip mounting clip secures the decorative door trim on dishwashers with short side panels, restoring a flush, stable front appearance and preventing the trim from rattling or coming loose. Ideal when the trim has shifted or separated. What it does:

• Secures the outer trim strip to the dishwasher door at short-side-panel mounting points.
• Keeps trim aligned and prevents rattling, sagging, or visible gaps.
• Restores the finished look of the dishwasher front after trim movement or damage.
• Works with the original trim assembly and mounting hardware to maintain proper fit.

• Always disconnect power to the appliance before accessing the door assembly and follow OEM service instructions.
• Access typically requires removing the inner or outer door panel or lower access panel; preserve existing screws and hardware for reassembly.
• Clip installs into the designated trim mounting location; confirm orientation before fastening and avoid over-tightening.
• Obtain the correct fasteners from the OEM parts list.

This dual water inlet valve controls water flow to appliance components like the dispenser and ice maker, restoring proper water delivery when the valve is functioning. It replaces a faulty or leaking inlet valve to help stop water issues. What it does:

• Opens and closes water flow to the appliance's water circuits (dispenser/ice maker) when signaled
• Commonly linked to no water dispensed or ice maker not filling
• Can be a source of slow fill or intermittent water delivery
• A leaking or stuck valve can cause visible leaks or water pooling

• One dual water inlet valve

• Shut off water supply and disconnect power before servicing
• Use basic hand tools; avoid overtightening connections to prevent damage
• Inspect inlet hoses and seals when replacing the valve

An integrated door switch for dishwashers that senses when the door is closed and allows the machine to start. Replacing a worn or damaged switch restores normal operation and helps prevent cycles from running with an open door. What it does:

• Detects door-closed position and tells the control board the door is secure
• Enables the dishwasher to start cycles only when the door is properly latched
• Prevents operation or pauses cycles if the door is open or not fully closed
• Common symptom: dishwasher won't start or stops mid-cycle when the door is opened

• Disconnect power to the appliance before attempting any service.
• Access typically requires removing the inner door panel or toe-kick; handle the door carefully to avoid damage.
• Replace the switch and reconnect wiring exactly as removed; ensure connectors are fully seated.
• After installation, restore power and ensure the door registers closed and the unit starts normally.

Regulator with o-ring.

The Drain Motor Assembly is an OEM part for Bosch dishwashers. The drain motor assembly is responsible for draining dirty water from wash cycles and filling the dishwasher with clean water for the next use.

Symptoms of a bad drain motor assembly can include:

• Dishwasher failing to completely drain wash water
• Continuous running or buzzing drain motor sounds
• Accumulation of standing water at the bottom

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Bushing included. To order bushing separately use 00165296. This is the right side hinge. For left side hinge use 00263115.

This small rubber gasket seals and cushions an M4 fastener to help prevent leaks and reduce vibration at attachment points. It's a compact replacement part used where a watertight or vibration-damping seal is needed. What it does:

• Creates a seal around an M4 screw or bolt to help prevent water intrusion
• Cushions fasteners to reduce vibration, noise, and metal-on-metal wear
• Restores a tightened fastener's proper sealing surface when the original gasket is worn
• Helps maintain appliance integrity around panels, brackets, or connections

• Power off and unplug the appliance before starting any repair.
• Confirm the gasket's size matches the fastener and seating area before installation.
• Install flat against the mating surface; tighten fastener snugly but avoid over-torquing which can deform the gasket.
• Handle small parts carefully and retain any removed hardware for reassembly.

This rear drum motor mounting bushing supports the motor shaft at the back of the tub, keeping the drum aligned and reducing wear. It restores smooth drum rotation and helps reduce noise and vibration when functioning properly. What it does:

• Centers and supports the motor shaft to maintain proper drum alignment.
• Cushions rotating components to reduce squealing, grinding, or scraping noises.
• Helps prevent excess drum wobble and uneven wear on the tub and bearings.
• Can stop intermittent rubbing or burning smells caused by a worn mounting surface.

• Disconnect power before starting and follow all safety precautions; service panels may have sharp edges.
• Access typically requires removing the dryer/heater assembly and drum.
• Inspect mating surfaces and surrounding components (shaft, bearing, seal). Replace any excessively worn parts to prevent repeat failures.
• Use only OEM-recommended parts and fasteners; do not force or press the part in without proper alignment.

The Regulator is an OEM part for Bosch ranges. This regulator controls gas flow to the burners, ensuring they receive the proper amount of fuel to achieve the desired cooking heat levels.

Causes of a bad regulator include cracks, jets becoming clogged over time, or damaged thermostatic components that improperly sense temperature.

Symptoms of a bad regulator include:

• Burners that will not ignite or light unevenly
• Inability to adjust burner flames precisely
• Burners that become too hot or too cool unexpectedly
• Yellow burner flames instead of blue

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

A sealing kit designed to replace worn seals in the dishwasher pump area to stop leaks and restore a watertight pump assembly. Ideal when seals fail and allow water to escape around the pump. What it does:

• Replaces worn or damaged pump seals to help stop leaks beneath the machine
• Restores the pump assembly's watertight seal for proper water circulation and drainage
• Helps prevent water damage to the cabinet and flooring caused by seal failure
• Commonly used when you find water under the dishwasher, visible leaks near the pump, or damp cabinet flooring

• One sealing kit

• Disconnect power and shut off the water supply before starting any repair
• Access usually requires removing the lower access panel and may require partial pump disassembly
• Keep track of small seals and O-rings during removal; inspect related parts for wear

This black replacement door handle restores a dishwasher's exterior grip and appearance, letting the door open and close securely. It matches factory fit and finish for compatible Bosch dishwasher models. What it does:

• Replaces a cracked, broken or missing door handle to restore normal door opening
• Provides a solid grip for pulling the dishwasher door open and closed
• Restores the appliance's exterior appearance when the original handle is damaged
• Fits the factory handle mounting locations and aligns with the door trim

• One black door handle

• Disconnect power to the dishwasher before starting any repair
• Support the door while removing fasteners to prevent it from closing unexpectedly
• Remove interior door panel or trim as required to access handle screws or clips
• Use manufacturer service manual or OEM instructions for step-by-step removal and reassembly

This actuator lever assembly with springs replaces a worn or broken control lever to restore proper mechanical movement in the appliance. It helps the dispenser/latch mechanism operate smoothly for reliable everyday use. What it does:

• Transfers motion from a control cam or motor to the latch or dispenser linkage
• Restores proper engagement when a broken or fatigued lever prevents operation
• Helps stop intermittent or failed cycle starts caused by damaged mechanical linkage
• Works as a direct-fit replacement that re-establishes spring tension and lever action

• Disconnect power before accessing internal components to avoid shock or injury
• Basic hand tools usually required; maintain original screw/hardware if reusing
• Inspect surrounding linkages and replace damaged clips or fasteners as needed