Bosch Parts

This door latch cover is the exterior trim that fits over the dishwasher door latch, restoring a finished appearance and protecting the latch mechanism from spills and wear. It matches stainless-steel finishes and keeps the latch area clean. What it does:

• Covers and protects the door latch assembly from moisture and grime.
• Restores the dishwasher door's exterior appearance when dented, scratched, or missing trim.
• Helps prevent debris build-up that can interfere with latch engagement.
• Compatible with latch installations that use a snap-on or screw-attached cover.

• Remove power to the appliance before starting any repair to avoid electrical hazard.
• Remove the inner door panel or access trim per service instructions to reach latch area.
• Install by aligning the cover over the latch and securing with the original screws or clips; do not force or bend the cover.
• If metal damage or latch misalignment is present, inspect latch mechanism and replace if necessary.

A small spring-style hose clamp used to secure flexible appliance hoses to fittings and prevent leaks. Simple, durable replacement that restores a tight connection for water and drain lines. What it does:

• Compresses around a hose to hold it firmly on an inlet, outlet or drain fitting
• Helps stop leaks caused by loose or slipping hoses
• Keeps hoses seated during normal appliance operation and vibration
• Commonly used on dishwasher and washer drain or water hoses

• One hose clip / spring clamp

• Disconnect power and water supply before starting repairs
• Use pliers to expand the clamp for removal and reinstall; ensure hose is fully seated before releasing clamp
• Inspect the hose and fitting for damage; replace any cracked or brittle hose
• Do not overtighten or deform clamp when installing; replace if corroded or weakened

This carafe glass insert replaces a damaged or leaking coffee carafe glass and restores a safe, visible vessel for brewed coffee. The included gasket helps form a leak-resistant seal so the carafe functions as intended. What it does

• Holds brewed coffee and provides clear visibility of liquid level.
• Gasket helps seal the insert to prevent drips and leaks during pouring.
• Replaces cracked, chipped or shattered glass that can cause leaks or safety hazards.
• Restores safe use when the original carafe glass has visible damage.

• Allow the appliance and carafe to cool completely before handling broken glass.
• Handle glass carefully and wear gloves to avoid cuts when removing a broken insert.
• Clean mating surfaces and seat the gasket fully to ensure a proper seal before use.
• Hand wash the glass insert; inspect gasket for proper fit and damage before reinstalling.

A replacement flip tine for the dishwasher lower rack that restores folding rack supports so you can load dishes of different sizes. Bright silver finish matches common rack coatings for a discreet repair. What it does

• Replaces a single lower-rack flip tine used to fold down and support dishes, bowls and glasses.
• Restores the rack's ability to flip tines up or down for flexible loading.
• Helps stop dishes from shifting during the wash cycle when a tine is broken or missing.
• Fits into the lower rack's tine socket and functions with the existing rack hardware.

• One silver lower-rack flip tine (single piece).

• Slide or snap the tine into the lower rack tine socket until it seats; no special tools usually required.
• Inspect surrounding rack coating and mounting clip before installing; replace damaged clips or rack parts if needed.
• Handle edges carefully; wear gloves to avoid cuts on metal rack parts.
• Disconnect power to the appliance before doing any repairs that require more than simple hand installation.

This retaining clip secures small appliance components in place to prevent movement and ensure reliable part alignment. It provides a simple, durable hold that keeps assemblies stable during normal use and service. What it does:

• Holds panels, covers, or wiring harnesses in position to prevent rubbing or disconnection
• Maintains alignment of moving or attached components to reduce noise and wear
• Helps prevent intermittent electrical or mechanical failures caused by loose parts
• Commonly replaced when broken, cracked, or missing after service or impact

• One retaining clip

• Basic hand tools may be required; inspect surrounding parts before reassembly
• Wear gloves and power off and unplug the appliance before servicing
• Replace only with the correct OEM-designated clip to ensure fit and function

This dishwasher sump assembly houses the pump inlet and integrated ball check valve to route wash water to the drain while preventing backflow. Replaces worn or cracked sumps to restore proper draining and prevent leaks. What it does

• Collects and channels dishwasher wash water from the tub to the drain pump.
• Integrated ball check valve stops backflow into the sump, helping prevent standing water and odor.
• Restores proper drain function when the existing sump is cracked, clogged, or leaking.
• Compatible with common Bosch/BSH dishwasher pump systems that use a molded sump with ball valve.

• One sump with integrated ball check valve (single assembly only).

• Disconnect power and water supply before starting any repair.
• Access typically requires removing the dishwasher lower kickplate and possibly tilting the unit; support the unit and follow the OEM service manual.
• Inspect surrounding seals, hoses, and pump gaskets for wear and replace as needed.

This is the left hinge cap. For right hinge cap use 00165295.

This door latch cover is a direct-fit replacement trim piece that protects and conceals the dishwasher door latch assembly while restoring a finished appearance. Keeps the latch area tidy and helps ensure the door closes cleanly. What it does:

• Covers and protects the door latch mechanism from debris and wear
• Helps the door latch engage and the door sit flush when closed
• Restores the appliance's cosmetic finish around the latch area
• Can address symptoms such as a loose-looking latch area or an unsealed door edge

• Disconnect power to the appliance before installing; follow lockout/tagout practices
• Basic hand tools (screwdriver or trim tool) are typically required to remove the old cover
• Align the new cover over the latch assembly and snap or fasten into place per OEM diagram
• If the latch mechanism or strike is damaged, replace those parts as needed for full repair

A reed switch door sensor that detects when the appliance door is closed so the control can start cycles. Replaces a failed magnetic sensor to restore reliable door-closed detection and normal operation. What it does

• Acts as a magnetic contact that signals the control when the door or lid is closed
• Helps prevent the appliance from starting if the door is open or not fully latched
• Common symptom fix for no-start, intermittent cycle start, or control not recognizing a closed door
• Works as the electrical switching element in the door/detector assembly

• One reed switch (single replacement sensor)

• Disconnect power to the appliance before replacing the part to avoid shock or damage
• Handle the switch and wiring gently; avoid bending or stressing terminals and solder joints
• Locate and access the door/detector area per your service manual or tech sheet; confirm connector orientation before installing

This spur gear is a direct-drive replacement gear that transfers rotary motion between motor and transmission components, restoring correct gear engagement and part movement in compatible appliances. What it does:

• Replaces a worn or stripped drive gear to restore proper mechanical engagement
• Helps eliminate slipping, erratic part movement, or loss of driven function
• Can stop grinding or clicking noises caused by damaged gear teeth
• Works as a direct mechanical link between motor/drive components and the driven assembly

• Disconnect power and water before any disassembly
• Requires disassembly of the drive/transmission housing; refer to OEM service manual for steps
• Inspect mating gears and shafts for wear—replace any damaged parts to prevent repeat failure
• Use only recommended lubricants per OEM guidance; do not force-fit or modify the gear

This door latch mechanism secures the appliance door and completes the door-switch circuit so the unit can operate. It replaces a worn or damaged latch to restore proper door closure and reliable operation. What it does:

• Engages and holds the door closed during cycles so the appliance can run.
• Activates the door switch/contact that signals the control board the door is closed.
• Commonly used when the door won't stay closed, the appliance won't start, or the latch feels loose or broken.
• Fits into the door frame and mates with the striker/handle to keep the seal tight.

• One door latch mechanism

• Disconnect power (unplug or switch off breaker) before servicing to avoid electrical shock.
• Access usually requires opening the door panel or removing the inner door; keep track of screws and clips.
• Handle carefully to avoid damaging the latch tabs or wiring; test door operation before reassembling fully.
• If wiring or mounting points are damaged, replace those parts as needed rather than forcing the latch.

This inner door is the interior panel for a dishwasher door that protects internal components and provides a finished inside surface. Replacing a damaged inner door restores proper sealing and appearance. What it does:

• Forms the interior surface of the dishwasher door and helps contain water during cycles
• Protects wiring, insulation, and electronics housed inside the door
• Helps maintain a proper seal to prevent leaks and improve wash performance
• Addresses symptoms like visible door damage, interior rust, dents, or moisture inside the door cavity

• Disconnect power and water supply before starting any repair
• Removing the outer door panel or control panel may be required;
• Keep fasteners and trim organized for reassembly; some clips or screws may be needed

This float switch lever is the actuator that moves the dishwasher's tub float to operate the water-level/flood-sensing switch, helping the appliance detect overfill and control fill/drain cycles. Replaces a worn or broken lever to restore proper float activation. What it does:

• Transfers movement from the tub float to the float switch so the machine senses water level correctly
• Commonly needed when a cracked or detached lever prevents the float from engaging the switch
• Can stop overfill-safety trips or no-fill symptoms caused by a non-responsive float assembly
• Works with the existing float and float switch; restores mechanical linkage function

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove lower access panels or tub components as required to reach the float assembly
• Inspect surrounding clips and the float for damage; replace any broken hardware
• Tighten securely but avoid over-torquing; test float movement and switch activation before reassembly