Bosch Parts

This float switch lever is the actuator that moves the dishwasher's tub float to operate the water-level/flood-sensing switch, helping the appliance detect overfill and control fill/drain cycles. Replaces a worn or broken lever to restore proper float activation. What it does:

• Transfers movement from the tub float to the float switch so the machine senses water level correctly
• Commonly needed when a cracked or detached lever prevents the float from engaging the switch
• Can stop overfill-safety trips or no-fill symptoms caused by a non-responsive float assembly
• Works with the existing float and float switch; restores mechanical linkage function

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove lower access panels or tub components as required to reach the float assembly
• Inspect surrounding clips and the float for damage; replace any broken hardware
• Tighten securely but avoid over-torquing; test float movement and switch activation before reassembly

This door handle replaces a worn or broken appliance door grip to restore a secure, comfortable surface for opening and closing. Designed to match the original fit and appearance for easy cosmetic repair. What it does:

• Provides a sturdy grip for opening and closing the appliance door
• Replaces cracked, loose, or cosmetically damaged handles
• Restores proper leverage to reduce stress on the door latch and hinges
• Helps improve the look of the appliance by replacing a worn handle

• One door handle

• Refer to your appliance model's service manual for step-by-step removal and installation instructions
• Installation typically requires basic hand tools; disconnect power (and water if applicable) before servicing
• Handle may attach with screws or snap-fit clips—keep removed fasteners for re-use unless replacements are provided

This water level regulator controls the appliance's water fill by sensing and regulating pressure/level for proper operation. Replacing a failing regulator restores correct fill behavior and helps prevent over- or under-fill conditions. What it does:

• Senses water level/pressure and signals the fill system to start or stop water flow
• Prevents overfilling by stopping the inlet when the correct level is reached
• Helps avoid underfilling that can cause poor wash or rinse performance
• Resolves symptoms like continuous filling, no fill, or erratic water levels

• Water level regulator

• Disconnect power and turn off the water supply before attempting replacement
• Handle electrical connections and hoses carefully; note wiring positions for reassembly
• Inspect hoses and seals for damage and replace if cracked or brittle
• Test the appliance through a short cycle after installation to ensure proper fill and operation

This fastening ring secures a rotating or stationary component in place to help prevent movement and vibration. It restores proper fit and alignment so assemblies run quietly and components stay locked in position. What it does:

• Holds shafts, bearings or housings in position to prevent axial movement
• Helps stop rattling, wobble or misalignment caused by a loose retaining component
• Maintains a secure mechanical connection between mating parts
• Used wherever a snap/retaining ring is required to lock a component on a shaft or in a bore

• Disconnect power and water before beginning any repair
• Use the correct pliers or tools for snap/retaining rings to avoid deformation
• Verify the ring matches the OEM part number and seating location before installation

This rubber gasket seals appliance openings to help prevent water and air leaks and restore proper door/tub sealing. It replaces a worn or damaged seal to reduce leaking and maintain normal appliance performance. What it does

• Creates a watertight/airtight barrier between mating surfaces to prevent leaks.
• Helps maintain operating temperature and efficiency by sealing the door/tub.
• Common symptom: visible water around the door or base during use.
• Common symptom: cracked, flattened, or distorted seal material that no longer compresses.
• Works as a direct replacement for the matching OEM seal when damaged or worn.

• One gasket as shown on the product page.

• Turn off power and water supply to the appliance before starting any repair.
• Remove the old seal carefully, clean the mounting channel of debris and residue, and inspect the mating surface.
• Press the new gasket evenly into the channel, starting at one corner and working around to ensure full seating without twists.
• Test the door closure and run a short cycle to confirm there are no leaks; re-seat if necessary.