Bosch Parts

Replacement push button for your dishwasher's control panel. Installs on the front console. Needed when your button is cracked, broken, or missing.

Threaded spacer for wall oven door handles. Installs between handle and door to maintain proper spacing. Replace if cracked, stripped, or missing.

Display screen blank, dim, or showing only dots? This washer display module control board restores cycle status visibility and front panel control.

This replacement lid is the outer cover used to protect internal components and help contain water and debris. It restores a finished appearance and helps the appliance operate without interference from loose or damaged tops. What it does:

• Covers and protects internal components from splashes, dust, and debris
• Helps maintain proper sealing and prevents items from falling into the machine
• Restores the appliance's finished appearance after damage or wear
• Can reduce rattles or interference caused by a cracked or warped lid

• One replacement lid

• Disconnect power and shut off water before servicing
• Handle carefully to avoid chipping or scratching painted surfaces
• Typical installation uses existing fasteners; inspect mounting points and replace hardware if damaged

Fix washer overfilling or underfilling issues with a water level pressure switch replacement. Controls water amount during wash cycles. Moderate DIY repair.

Replacement silverware basket holds and organizes forks, knives, and spoons in your dishwasher. Replaces cracked, broken, or missing cutlery holders.

Telescopic tube for canister vacuums. Connects between the hose and floor tool. Replace if cracked, broken, or plastic connector is damaged.

Split broiler pan for wall ovens. Installs in broiler compartment. Replace if cracked, warped, or heavily stained to restore cooking performance.

Replaces the outer door panel on your dishwasher. Needed when the existing panel is dented, scratched, discolored, or you want a different finish.

This genuine OEM replacement part is a pulley assembly for dryers. Sometimes called an idler arm, the pulley assembly keeps the dryer drive belt under tension as the belt wraps around the dryer drum. If the dryer is no longer spinning properly and is making a lot of noise, the pulley assembly may need to be replaced. Luckily this repair is a relatively simple process.To remove the old dryer pulley assembly, start by making sure the dryer is unplugged. Remove the lint screen from the top of the dryer. Remove the two Phillips screws by the lint screen opening. Depress the clips that hold the top cover down. Lift the top cover and keep it in an upright position. Disconnect the wire harness to the switch that separates the connector. Remove the screws on the front panel. Lift the panel forward and set it to the side. Next, lift the drum and locate the pulley assembly under the drum. Lift the belt off the motor pulley to remove the assembly. Set the new pulley assembly in the same position as the old one and make sure everything is aligned. Rotate the drum to make sure it rotates smoothly. reinstall the panels.This replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador dryers.

This cotton insulation piece provides noise- and heat-damping for the appliance cabinet area, helping reduce operating sound and limiting heat transfer around the tub. Designed to replace worn or damaged insulation for a snug fit and quieter operation. What it does:

• Reduces operating noise by adding a sound-dampening layer around the tub area
• Helps limit heat transfer from the heater/tub to surrounding panels
• Provides a protective barrier to reduce vibration-related noise
• Restores the original insulation barrier when the old material is compressed or torn

• One cotton insulation panel, white, 46 dB variant

• Disconnect power and water supply before beginning any service
• Handle the insulation gently to avoid tearing; wear gloves and a dust mask if needed
• Remove access panels and old insulation, then position and secure the new piece in the same orientation
• Reinstall panels and restore power; test for proper operation and reduced noise

This dispenser door is the outer cover for the dishwasher detergent cup, providing a secure compartment for powder or tablet detergent until the wash cycle releases it. Restores proper detergent release and keeps the cup sealed during fill and wash. What it does:

• Covers and seals the detergent cup so detergent stays dry until the cycle releases it
• Pops open at the correct time so detergent dispenses into the wash
• Replaces cracked, warped, or otherwise damaged doors that won't latch or open
• Helps prevent detergent from dissolving prematurely or leaking into the tub

• Disconnect power and water to the appliance before servicing
• Remove the inner door panel or access the dispenser per the service manual to replace the door
• Handle plastic parts carefully to avoid damage; use proper hand and eye protection

If your cooktop won't heat or heats unevenly, this heating element restores proper cooking temperatures. Direct replacement for worn or burned-out elements.

2 included - Front load