Bosch Parts

Replacement lid plug cap for blender jars. Seals the fill opening on top of the blender lid. Order new if yours is cracked, broken, or missing.

Color: White

This mechanical door latch secures the dishwasher door during operation so cycles can run safely and the unit can seal properly. It replaces a worn or broken latch to restore reliable door closure and cycle starts. What it does:

• Physically holds and locks the door closed during wash cycles
• Triggers or maintains the door-closed state so the control will allow the cycle to start
• Commonly replaces units that are cracked, bent, or no longer latching
• Resolves symptoms like a door that won't stay closed, a dishwasher that won't start, or intermittent cycle interruptions

• Disconnect power to the appliance before beginning any repair
• Remove the inner door panel to access the latch; keep fasteners organized
• Inspect surrounding strike and mounting tabs for damage before installing

Front cover for dishwasher pump housing. Replaces cracked, broken, or missing pump housing covers. Installs on the front of the circulation pump assembly.

Replacement drum drive belt for your washer. Transfers motor power to rotate the drum during wash cycles. Replace if drum won't spin or belt is frayed.

Jet holder assembly secures the orifice that meters gas flow to your cooktop burner. Replace if cracked, stripped threads, or missing nut components.

This threaded spacer or screw is used to secure the door handle to the front of a wall oven door. It threads through the handle mounting holes and provides proper standoff distance between the handle and the door panel. Replace this part if the oven door handle feels loose, wobbles, or if the original spacer is stripped or missing.

Display screen blank, dim, or showing only dots? This washer display module control board restores cycle status visibility and front panel control.

Fix washer overfilling or underfilling issues with a water level pressure switch replacement. Controls water amount during wash cycles. Moderate DIY repair.

This is a frying pan designed for use inside a wall oven or range. It sits on the oven rack and is used for stovetop-style cooking tasks such as frying or searing within the oven cavity. Replace this pan if it is warped, the coating is damaged or peeling, or if it no longer sits flat on the rack.

Replaces the outer door panel on your dishwasher. Needed when the existing panel is dented, scratched, discolored, or you want a different finish.

This genuine OEM replacement part is a pulley assembly for dryers. Sometimes called an idler arm, the pulley assembly keeps the dryer drive belt under tension as the belt wraps around the dryer drum. If the dryer is no longer spinning properly and is making a lot of noise, the pulley assembly may need to be replaced. Luckily this repair is a relatively simple process.To remove the old dryer pulley assembly, start by making sure the dryer is unplugged. Remove the lint screen from the top of the dryer. Remove the two Phillips screws by the lint screen opening. Depress the clips that hold the top cover down. Lift the top cover and keep it in an upright position. Disconnect the wire harness to the switch that separates the connector. Remove the screws on the front panel. Lift the panel forward and set it to the side. Next, lift the drum and locate the pulley assembly under the drum. Lift the belt off the motor pulley to remove the assembly. Set the new pulley assembly in the same position as the old one and make sure everything is aligned. Rotate the drum to make sure it rotates smoothly. reinstall the panels.This replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador dryers.

This cotton insulation piece provides noise- and heat-damping for the appliance cabinet area, helping reduce operating sound and limiting heat transfer around the tub. Designed to replace worn or damaged insulation for a snug fit and quieter operation. What it does:

• Reduces operating noise by adding a sound-dampening layer around the tub area
• Helps limit heat transfer from the heater/tub to surrounding panels
• Provides a protective barrier to reduce vibration-related noise
• Restores the original insulation barrier when the old material is compressed or torn

• One cotton insulation panel, white, 46 dB variant

• Disconnect power and water supply before beginning any service
• Handle the insulation gently to avoid tearing; wear gloves and a dust mask if needed
• Remove access panels and old insulation, then position and secure the new piece in the same orientation
• Reinstall panels and restore power; test for proper operation and reduced noise