Parts for Lg WM1355HR: Control Panel / Dispenser Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This Leg Adjusting Wrench is a simple tool used to turn and secure appliance leveling legs so washers and dryers sit flat and operate quietly. It makes adjusting legs faster and helps reduce rocking and vibration. What it does:

• Fits over standard appliance leveling legs to raise or lower each corner
• Helps stabilize machines to prevent rocking and uneven operation
• Reduces vibration and noise caused by unlevel appliances
• Useful when installing, moving, or re-leveling washers and dryers

• Turn legs slowly and adjust one corner at a time until the appliance sits level.
• Unplug the appliance (and shut off gas supply for gas dryers) before performing major moves or checks.
• Use caution to avoid pinching fingers when lowering legs; keep hands clear of pinch points.
• Check for damaged feet or mounting hardware and replace as needed.

Excessive noise or debris inside your washer? This rear cover panel shields internal components and maintains airflow. Straightforward DIY fix.

Secures internal washer components and maintains proper alignment. Replace when brackets are worn, broken, or causing rattling. Confirm fit with your model number.

Secures washer drum during moving or transport. Immobilizes internal components to prevent damage. Replace if missing, lost, or needed for relocation.

Replace your washer's outer tub assembly if cracked, damaged, or leaking. This structural component houses the inner drum and seals the wash system.

Supports the inner drum for smooth rotation during wash and spin cycles. Replace when you hear grinding, loud noise, or excessive vibration. Confirm fit with your model number.

Supports smooth drum rotation in your washer. Replace if you hear loud roaring or grinding noises during spin cycles. Confirm fit with your model number.

Washer won't spin or makes grinding noises? The motor rotor bolt secures the rotor to the motor shaft. Requires a 17mm socket for installation.

Seals between inner and outer tubs to prevent water leaks during wash cycles. Replace if you notice leaks or after bearing replacement. Verify fit.

This balance weight stabilizes the washer drum to reduce vibration and keep the washer steady during spin cycles. Replacing a worn or damaged weight restores smoother operation and reduces shaking and noise. What it does:

• Adds mass to the washer frame/drum assembly so the tub stays balanced during spin
• Helps prevent excessive vibration, banging, and movement during high-speed spins
• Reduces noise caused by an unbalanced load or damaged weight
• Supports proper drum alignment to avoid premature wear on bearings and suspension parts

• One balance weight

• Always unplug the washer before starting any repair to avoid electrical shock
• Support the drum/tub when removing or installing the weight to prevent component damage
• Reuse or replace any mounting hardware only if explicitly specified by the manufacturer
• If vibration persists after replacement, inspect suspension, shock absorbers, and mounting points

Holder assembly for washer and washer-dryer combo units. Secures internal components in position. Replace if cracked, broken, or missing to restore stability.

This replacement refrigerator door gasket seals the door to keep cold air inside, helping restore proper cooling and reduce frost, condensation, and energy loss from a damaged or worn seal. What it does:

• Creates an airtight seal around the refrigerator door to maintain internal temperature.
• Prevents warm air infiltration that can cause frost buildup and uneven cooling.
• Reduces condensation and helps improve compressor efficiency when sealing properly.
• Common symptoms of a failing gasket: visible cracks or gaps, cold air leaks, frost or moisture buildup, and higher energy use.

• Remove the old gasket and clean the door flange before installing the new seal.
• Press the gasket evenly into the door channel; some models use retaining clips or screws—model-specific instructions.
• Check that the gasket seats uniformly with the door closed and make minor adjustments as needed.

Motor harness wiring for washers. Connects motor to control board. Replace if wires are damaged, frayed, connectors broken, or harness is worn out.

Replace your washer's door inner frame to restore proper fit and alignment of the door liner and trim. Essential when the frame is cracked or damaged.

Replacement door handle for washer and washer-dryer combo units. Restores grip for opening and closing. Replace when cracked, broken, loose, or missing.

Fix DE door error codes or doors that won't latch with this washer door latch hook. Simple 15-minute DIY repair with video guide. Secures door during cycles.

If your washer fills slowly, overfills, or fills when off, the water inlet valve may need replacement. Simple DIY repair that stops leaks fast.

Fix washer IE error or no water flow issues with this water inlet valve. Controls hot or cold water flow into wash drum. 15-minute DIY repair.

Mounts to the washer's lower frame to secure components and maintain alignment. Replace if bracket is cracked, broken, rusted, or missing hardware.

Replace a broken, rusted, or missing leveling leg assembly. Installs at the base to stabilize your washer, reduce vibration, and adjust height.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This inlet hose supplies fresh water from the household line to the dishwasher. Replace a damaged or leaking hose to help restore proper filling and prevent water leaks during operation.

• Channels water from the supply valve to the dishwasher's inlet
• Common failure signs: leaks under or behind the unit, fill errors, slow or no fill
• Helps resolve intermittent water supply issues caused by a kinked or cracked hose

• Unplug power and shut off the water supply before starting
• Place a towel or pan to catch residual water when disconnecting
• Check for leaks after installation and tighten connections as needed

Fix leaks or poor water flow with a new washer inlet hose. This part channels household water supply into your machine for proper filling and operation.

This part may be black or gray in color.

Door boot seal bellows for front-load washers. Creates watertight seal between drum and door. Replace if torn, cracked, moldy, or leaking during wash cycles.

Heater assembly for washer dryer combos. Installs in the drying system to generate heat. Replace if cracked, corroded, or damaged to restore proper drying.

Inlet hose for washers. Connects water supply to machine. Replace if cracked, leaking, kinked, or worn. Essential for proper water flow to drum.

Fix standing water, loud pump noise, or continuous filling in your washer. This drain pump motor assembly restores water removal. Moderate DIY repair.

Drain hose carries used water from washer to household drain. Replace if cracked, leaking, deteriorated, or damaged to prevent water overflow issues.

Does not come with a hose or filter. These have to be purchased separately

Washer won't drain or shows OE error? This drain pump assembly removes water during spin cycle. Moderate DIY repair with video guide available.

Water leaking from filter area or drain error? This washer pump filter traps lint and debris. Easy DIY fix with video guide—most install in minutes.

This rotor position sensor (Hall sensor) tracks the direct-drive motor's rotor position and speed so the control can commutate the washer motor accurately. Replacing a failed sensor can restore proper wash/agitate and spin performance. What it does:

• Detects rotor position and speed from the stator assembly
• Sends timing feedback to the control for correct motor start, direction, and speed
• Supports smooth agitation and spin ramp-up/ramp-down
• Failure may cause: no spin or agitation, cycle stalling/pausing, or an LE motor error code

• 1 rotor position sensor assembly

• Unplug the washer and shut off water; wear protective gloves
• Access the motor at the rear of the tub; remove the back panel if needed
• Remove the rotor and stator; support the stator to protect wiring, then unclip/unscrew and replace the sensor
• Align the sensor correctly and seat the connector fully before reassembly and testing

This rotor assembly is the rotating half of your washer's direct-drive motor. It mounts to the rear of the tub and, working with the stator, spins the drum for wash and spin cycles to restore smooth operation.

• Couples with the stator to drive the inner tub during wash and spin
• Helps resolve no- or slow-spin complaints
• Can address a drum that won't turn or turns intermittently
• May reduce grinding/clicking from the rear caused by damaged rotor magnets

• Unplug the washer and turn off water supply before servicing
• Access from the rear; remove the center bolt and pull the rotor straight off the shaft
• Magnets are strong—keep fingers clear; align splines/keyway on reinstallation
• Tighten the center bolt securely and inspect the stator and sensor while open

This hinge spring restores proper tension to the door so it opens and closes smoothly and stays aligned. Replacing a fatigued spring helps prevent sagging or slamming and supports a consistent, reliable door close.

• Provides the return tension/counterbalance for the door hinge mechanism
• Assists smooth opening/closing and helps the door stay properly aligned when latched
• Helps maintain consistent closing force over time
• Failure symptoms include: door drops quickly, won't stay aligned or fully closed, weak/squeaking spring action

• Disconnect power before service; allow any hot surfaces to cool
• The hinge and spring are under tension—support the door and release/install tension carefully
• Note spring orientation and hole positions before removal; match them on installation
• Access may require removing trim or the door; keep fasteners organized for reassembly

Supports suspension springs that stabilize the washer drum, reducing vibration and noise during operation. Replace if drum shakes excessively or hits sides. Verify fit with your model number.

Replace your washer's damaged, frayed, or missing power cord assembly. Restores safe electrical connection from wall outlet to machine inlet.

The Pump Hose is an OEM replacement part for LG washing machines. It is a flexible tube that connects the pump assembly to the internal tub and spins through the detergent dispenser area. The pump hose is responsible for circulating and removing water during the wash and rinse cycles. 

Symptoms of a bad pump hose include:

• Leaks or water not fully draining from the washer 
• Slow or inefficient filling and draining of water  
• Pump running loudly or continuously
• Wet areas under or around the washer

Causes of failure can be cracks or splits developing in the tubing from repeated bending and flexing over time, or blockages restricting water flow.

It is also compatible with some Kenmore models.

Pivot hanger assembly that supports and stabilizes washer components. Replace if worn, damaged, or causing misalignment to restore smooth movement.

Fix DE error codes and door lock failures with this washer door lock switch. Most DIYers complete this repair in under an hour with our video guide.

Secures rubber hoses to fittings with constant spring tension to prevent leaks. Replace when rusted or weakened to maintain a tight seal. Confirm fit.

Secures rubber hoses to fittings with constant spring tension to prevent leaks. Replace when rusted or weakened to maintain a tight seal. Confirm fit.

The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.

Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.

Symptoms of a bad clamp include:

• Water leaking from hose connections
• Hoses coming loose or detaching during operation
• Visible rust or damage on the clamp
• Poor water flow or pressure issues

This OEM LG part is also compatible with Sears/Kenmore models.

Secures washer hoses to pumps, tubs, and drain fittings to prevent leaks. Replace when weakened, rusty, or damaged to maintain tight connections.

Fix washer leaks with this hose clamp. Secures hoses to pumps and valves, preventing water leaks and disconnections during wash cycles. Simple repair.

Forms a watertight barrier between washer tub and front panel. Replace if leaking, torn, or harboring odors. Confirm fit with your model number.

Replace your washer's door boot seal if you notice water leaks around the door or visible cracks in the rubber. Maintains watertight seal on front-load washers.

Air chamber dome for washer pressure systems. Installs on the tub assembly to regulate water level sensing. Replace if cracked, damaged, or missing.

Fix washer not filling or slow fill issues. This water inlet hose connects your home supply to the washer inlet valve. Simple DIY install restores flow.

Connector hose for washers and washer-dryer combos. Links water supply lines or internal components. Replace if cracked, leaking, or disconnected.

Leaking washer water line? This connector hose seals your appliance water line to internal plumbing, stopping leaks and restoring water flow. Simple fix.

Replaces worn or broken shock absorbers that stabilize the drum in your washer. Installs at the base of the tub to dampen vibrations during spin cycles.

Locking pin for shock absorber.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.