Parts for Lg DLEX7800VE: Control Panel / Plate Assy Parts

This washer tub assembly is the stationary outer tub that surrounds the spin basket and contains the wash water. Replacing a cracked or damaged tub helps stop leaks and restores proper clearance for smooth, quiet washing and spinning.

• Creates a watertight chamber around the basket to hold wash and rinse water
• Maintains proper basket clearance; damage can cause rubbing or scraping sounds
• Provides connection points for hoses and water-level components
• Common signs it may be needed: leaks from the tub area, visible cracks or warping, persistent out-of-balance/spin errors, or internal scraping/grinding noises

• Disconnect power and water; shut off supplies and safely drain remaining water
• This is a major repair—allow time and consider a second person to help lift/support the tub
• Transfer model-specific parts from the original tub to the new tub as needed; reinstall all clamps, bolts, and sensors securely
• After reassembly, level the washer, and run a test cycle to check for leaks

A replacement front panel assembly that restores the appliance's exterior console and control area for a factory-finish look. Replaces a cracked, faded, or damaged outer console so buttons and display mount securely. What it does:

• Replaces the outer front console and provides the mounting surface for control buttons and display
• Restores cosmetic finish and alignment when the original panel is cracked, warped, or broken
• Helps eliminate rattles or loose trim caused by damaged panel edges or broken clips
• Works with existing controls and electronics

• One front panel assembly (outer console) as pictured

• High-level replacement: remove top/control housing and detach retaining clips/screws; save hardware for reinstallation
• Handle panel carefully to avoid scratching the finish or damaging mounting tabs
• Disconnect power before starting and follow appliance-specific disassembly steps in the service manual

The Heater Assembly is an OEM replacement part for LG dryers. It is a critical component responsible for generating the heat necessary for drying clothes efficiently and effectively.

Symptoms of a bad heater assembly:

• Dryer not producing enough heat or failing to dry clothes completely
• Excessive drying times or inconsistent drying performance
• Visible damage or breaks in the heating element coil
• Burning odors or smoke emanating from the dryer during operation

Causes of a bad dryer heater assembly can include mechanical failure, electrical malfunctions, or simply reaching the end of its lifespan due to repeated heating and cooling cycles.

This OEM LG part is also compatible with Sears/Kenmore dryer models.

Fix a blank or unresponsive dryer display with this display power control board assembly. Restores touch controls and button functions when the interface fails.

The Dryer Drum Baffle is an OEM part for LG dryers. This baffle is attached to the inside of the dryer drum and is designed to help lift and tumble clothes during the drying cycle. 

Causes of a bad dryer drum baffle can include wear and tear from regular use, physical damage from heavy or sharp objects, or becoming loose due to vibration over time. 

Symptoms of a bad dryer drum baffle include:

• Thumping or banging noises during the drying cycle
• Clothes not tumbling properly, leading to uneven drying
• Loose or rattling baffle inside the drum
• Visible damage or breakage on the baffle

This OEM LG part is also compatible with some Kenmore models.

This main printed circuit board (power control board assembly) controls core appliance functions and electrical power distribution for the control system. Replacing a faulty board restores responsive controls and reliable power management. What it does:

• Regulates power to the appliance control circuits and coordinates electronic functions.
• Processes user inputs and sends signals to motors, valves, heaters, and display modules.
• Common symptoms of a failing board: appliance won't power on, unresponsive controls, erratic behavior, or persistent control-related error codes.
• Use only the exact replacement board to avoid compatibility and safety issues.

• Disconnect power (unplug or switch off circuit breaker) before service.
• Take photos or label wiring connectors to ensure correct reassembly.
• Avoid touching circuit traces or components; handle board by edges and ground yourself to prevent static damage.

The Belt is an OEM replacement part for LG dryers that is responsible for connecting the motor to the drum to allow it to tumble. Over time, dryer belts can stretch, wear out, or even break, leading to a drum that won't turn and clothes that don't dry properly.

Symptoms of a bad Dryer Belt include:

• The dryer motor running but the drum not turning.
• A squealing or thumping noise coming from the dryer.
• The dryer not starting at all.

Causes of failure can include regular wear and tear from the dryer's operation, overloading the dryer beyond its capacity, which puts extra strain on the belt, or a misalignment that causes uneven wear. A damaged belt can prevent your dryer from functioning correctly, leading to inefficiency in drying clothes and potential motor damage due to unnecessary strain.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Hi Limit Thermal Fuse is an OEM part for LG dryers. This fuse is a safety device that protects the dryer from overheating by cutting off power to the heating element if the dryer’s temperature exceeds a safe limit. It ensures that the dryer operates within safe temperature ranges, preventing potential fire hazards.

Replace the hi limit thermal fuse if it becomes faulty due to wear and tear, a buildup of lint, or exposure to high temperatures over time. A malfunctioning fuse can compromise the dryer’s ability to regulate heat properly.

Symptoms of a bad hi limit thermal fuse include:

• The dryer not heating
• The dryer shutting off unexpectedly during a cycle
• No response from the dryer when attempting to start a cycle
• Extended drying times due to lack of heat

This OEM LG part is also compatible with Sears/Kenmore models.

Replaces a cracked, broken, stripped, or missing control knob on your dryer or washer. Restores secure grip and proper engagement with the control shaft.

Replace your dryer drum seal when clothes take longer to dry or you notice lint buildup. Maintains heat efficiency and prevents air leaks. Confirm fit with your model number.

The Hi Limit Thermostat Assembly is an OEM part for LG dryers. This thermostat monitors and regulates the temperature within the dryer to prevent overheating, ensuring safe and efficient operation. It acts as a safety device that shuts off the heating element if the dryer exceeds a certain temperature, protecting the appliance and your home from potential fire hazards.

Over time, the hi limit thermostat can fail due to wear and tear, electrical issues, or repeated exposure to high temperatures. If the thermostat becomes faulty, it can lead to improper temperature regulation within the dryer.

Symptoms of a bad hi limit thermostat include:

• The dryer overheating
• The dryer not heating at all
• The dryer shutting off mid-cycle
• Extended drying times due to inconsistent heating

This OEM LG part is also compatible with Sears/Kenmore models.

Thread-forming fastener that secures panels, brackets, and internal components. Replace this screw if it's missing, stripped, or damaged during repairs.

Front trim decor panel that restores the finished appearance of your dryer door assembly. Replaces cracked, scratched, faded, or missing decorative trim.

Replace your dryer drum assembly if clothes aren't tumbling, you hear scraping noises, or the drum won't rotate. Moderate DIY repair in 1-2 hours.

This replacement top plate assembly is the upper cooktop panel for your range. It provides a flat, secure surface for burner components and protects the chassis below from heat, spills, and everyday wear.

• Forms the cooktop surface and mounting points for burner components
• Shields internal wiring/valves from spills, heat, and debris
• Damage can cause burners or grates to sit unevenly or create sharp edges/gaps
• Restores appearance and proper support when the original is dented, warped, or rusted

• Disconnect power; shut off gas and allow the appliance to cool
• Remove grates, burner caps and heads; disconnect igniter wires as needed
• Remove mounting screws, lift off the old panel, and set the new assembly in place
• Wear cut-resistant gloves and verify proper burner operation after reassembly

This upper plate is the replaceable trim/cover that fits inside the top of the microwave cavity to protect internal components and help direct airflow. Replacing a damaged plate restores proper coverage and reduces debris buildup. What it does

• Covers and protects internal microwave components at the top of the cavity
• Helps maintain proper airflow and part alignment inside the oven
• Prevents food and debris from contacting internal wiring and electronics
• Reduces rattling or vibrations caused by a warped or loose plate
• Visible cracks, warping, or burn marks are common signs it needs replacement

• One upper plate as pictured

• Disconnect power at the wall and allow the oven to fully power down before servicing
• Remove fasteners or clips holding the old plate, align tabs, then secure the new plate with the original hardware
• Do not operate the microwave with covers removed; complete the repair

LED light illuminates your dryer drum for easy viewing during operation. Replace when light dims, flickers, or burns out. Verify fit with your model.

Fix improper airflow or loose connections in your dryer with this connector nozzle. Restores correct routing and reduces leaks. Direct-fit replacement.

Dryer duct assembly that connects the drum to the blower housing. Replace if cracked, damaged, or has torn foam seals around openings.

The Roller Kit is an OEM part for LG dryers. This 4 roller kit includes replacement drum support rollers, which are essential for allowing the dryer drum to rotate smoothly during operation. The rollers are designed to provide stable support for the drum, minimizing noise and ensuring efficient drying performance. 

Over time, drum rollers can wear out due to continuous use, exposure to heavy loads, or lack of proper lubrication. When the rollers become damaged or worn, they may develop flat spots, lose their smooth surface, or begin to squeak. These issues can lead to improper drum rotation or increased strain on other dryer components.

Symptoms of a bad Roller Kit include:  

• Loud squeaking, rumbling, or thumping noises during operation  
• The dryer drum not spinning or rotating unevenly  
• Excessive vibrations while the dryer is running  

This OEM LG part is also compatible with Sears/Kenmore.

This is an authentic OEM drum support roller sourced directly from the manufacturer for use in clothes dryers. During the drying cycle, the drum turns and tosses the clothes around to distribute heat. This drum support roller holds the drum in place as it rotates. Over time, the heat from the dryer can lead to the roller becoming worn. If the dryer is making squealing sounds or thumping when operating, the support roller is worn out and should be replaced. Before replacing the drum support roller, make sure the power is disconnected from the dryer. Remove the top and front panel of the dryer to reach the drum. The idler pulley and dryer belt are underneath the drum; remove these and then take the drum out of the unit and set it aside. Remove the mounting bracket holding the worn drum support roller. Remove and replace the worn roller. While the dryer is apart, inspect the remaining support rollers. Reverse the steps used and put the dryer back together. Power the dryer and make sure the drum turns.This is a black and white, rubber and metal part that is individually sold. It does not come with assembly hardware. This drum support roller is designed for dryers manufactured by LG, Kenmore, and General Electric.

A manufacturer-configured replacement component designed to restore the appliance's original factory settings and functions. Use this part when a model-specific, pre-configured module is required to return correct operation. What it does:

• Provides the factory-specific configuration and setup programmed by the manufacturer
• Restores functions controlled by the module when configuration or programming is corrupted
• Resolves symptoms such as appliance not starting, control panel unresponsive, or intermittent/erratic operation linked to configuration errors
• Ensures compatibility with model-specific features when the appliance requires a pre-configured assembly

• Disconnect power to the appliance before starting any work
• Handle electronics carefully; observe electrostatic discharge (ESD) precautions for circuit boards or modules
• Match connectors and mounting locations to the original part; do not force connectors

Dryer door hinge connects the door to the cabinet frame. Replace if cracked, broken, or worn causing misalignment or door sagging. Installs with 3 screws.

Restore smooth, aligned door movement with this refrigerator door hinge assembly. A worn or bent hinge can cause sagging and poor sealing; replacing it helps the door close properly so your fridge maintains consistent performance. What it does:

• Allows the door to pivot smoothly on the cabinet
• Helps keep the door aligned for proper gasket contact and sealing
• Replaces worn or bent hinge components to restore correct door operation
• Typical symptoms: door sagging or rubbing, difficulty closing, uneven gasket contact, squeaks/clicks when opening or closing

• One hinge assembly

• Unplug the refrigerator; shut off water supply to the unit
• Support the door and use a second person to prevent dropping or misalignment
• Note/mark hinge positions and transfer any spacers or caps from the original hinge as needed
• After installation, verify even gasket contact and adjust leveling before tightening fasteners fully

Dryer lint filter screen traps lint and debris during drying cycles. Replace if cracked, damaged, or lost to maintain airflow and efficiency.

This replacement holder secures a small appliance component in place to restore proper alignment and reduce vibration. It's a direct-fit bracket designed to hold components steady and prevent movement that can cause noise or malfunction. What it does:

• Keeps the associated component firmly mounted to its chassis or support
• Prevents rattling, misalignment, or intermittent contact caused by a damaged or missing holder
• Helps maintain proper operation of the component it supports
• Common symptoms: visible crack or break in the holder, loose or shifting component, or new noise from the area

• One replacement holder as shown

• Disconnect power and/or water supply before beginning any repair
• Inspect surrounding parts for damage before installing the new holder
• Basic hand tools are typically required; avoid overtightening fasteners

Small trim cap that covers unused access holes on your dryer cabinet. Replace if cracked, broken, missing, or worn to protect internals and maintain a clean finish.

The Screw is an OEM part for LG dryers. This screw secures the front panel to the outer housing, ensuring a properly assembled unit.

Causes of a bad screw can include stripping of threads from over-tightening, loss of the screw from repeated access to internal components, or damage such as cracking from dropping or other impact.

Symptoms of a bad front panel screw include:

• Loose, detached, or missing front panel assembly
• Accessibility issues opening or closing the dryer door
• Reduced stability of the overall dryer cabinet structure

This OEM LG part is also compatible with some Kenmore models.

Fix a dryer door that won't stay closed or latched with this door lock assembly. Restores secure door closure for safe operation. Simple DIY repair.

Note: Does not include moisture sensor bars. For the moisture sensor bars, order 2 of part# 6500EL3001A.

The Guide Cover is an OEM part for LG dryers. The part allows dust and debris to exit the dryer drum while preventing small clothing items from slipping through.

Causes of a bad Guide Cover can include accumulation of lint and debris that can restrict airflow, physical damage from handling or excessive use, and general wear that can compromise the fit and effectiveness of the cover.

Symptoms of a bad Guide Cover include:

• Increased drying times due to poor airflow.
• Unusual noises from lint hitting the fan or other components.
• Overheating of the dryer.
• Visible damage or misalignment of the cover that affects performance.

This OEM LG part is also compatible with Sears/Kenmore.

Precision mounting screw for dryers and laundry centers. Replaces missing, stripped, or damaged screws that secure panels, brackets, and assemblies. Restores stability.

This safety interlock assembly secures the washer door and signals the control when it's safe to run a cycle. Replacing a faulty unit helps restore proper locking and start functions to prevent interruptions and error codes.

• Locks the washer door and confirms it is closed to allow the cycle to start
• Sends door-closed/locked status to the control throughout the cycle
• Helps prevent the door from opening during spin or when water is present
• Common symptoms: won't start, won't lock/unlock, door error (dE) messages, cycle stops mid-wash

• Disconnect power before servicing; wear cut-resistant gloves
• Access the lock at the door opening; remove the mounting screws and disconnect the harness
• Transfer connectors to the new assembly, align, and secure without overtightening
• Ensure the door strike aligns smoothly with the new lock before testing

Guides and secures the lint filter in place within your dryer. Replace if cracked, broken, or missing to properly hold the lint screen assembly.

Guides and secures the lint filter in place within your dryer. Replace if cracked, broken, or missing to properly hold the lint screen assembly.

Distortion spring that applies tension within the dryer mechanism. Replace if fatigued, broken, or missing to restore proper tension and assembly function.

Secures brackets, panels, and covers on your dryer. Replace missing, stripped, or damaged screws to keep components aligned and prevent rattling.

The Dryer Moisture Sensor Bar is an OEM part for LG dryers. It plays a critical role in detecting the moisture level of clothes during the drying cycle, enabling the dryer to adjust the drying time automatically. This ensures efficient operation, preventing over-drying, which can damage fabrics and increase energy consumption.

Symptoms of a bad Dryer Moisture Sensor Bar include:

• Clothes remaining damp after a complete drying cycle
• The dryer continually running without stopping
• Inconsistent drying results, with some clothes over-dried and others still wet

Causes of a bad moisture sensor bar can stem from a buildup of lint and fabric softener residue, which insulates the sensor and impairs its ability to accurately detect moisture. Additionally, wear and tear or damage from loading and unloading can affect its functionality.

Regular cleaning and maintenance are recommended to ensure that your LG dryer operates efficiently and preserves the life of your clothes.

Dryer won't auto dry or cycles run too long? This moisture sensor wire harness connects sensor bars to control. Restores accurate dry cycles. DIY-friendly.

Hole cap for dryers. Covers unused openings in the dryer cabinet or control panel. Replace if cap is cracked, broken, missing, or no longer fits securely.

This damper assembly mounts at the microwave's exhaust outlet to direct airflow outside and block backdraft when the fan is off. Replacing a cracked or warped damper restores venting performance and helps reduce drafts and rattling noise.

• Opens with blower airflow and closes when off to help prevent outside air from entering through the duct
• Directs steam, smoke, and cooking odors to the exhaust path
• Helps reduce drafts/backdraft when the fan is not running
• Common failure signs: weak venting, flap stuck open/closed, or rattling/flapping noises

• Disconnect power at the breaker; if over-the-range, support the unit per manufacturer instructions
• Remove the vent grille/top cover to access the outlet and take out the old damper; reuse existing hardware as needed
• Match the new damper's orientation to the original so the flap opens with airflow and moves freely
• Beware sharp sheet-metal edges; wear cut-resistant gloves and test the fan after reassembly to confirm proper operation

Secures the door hinge to your dryer cabinet for proper alignment and smooth operation. Replace if the door sags, rubs, or won't stay open. Confirm fit with your model number.

Secures the dryer door hinge to the cabinet frame. Replace this mounting bracket if it's cracked, broken, or worn to restore proper door alignment.

This holder is a small mounting bracket that secures internal components in place, helping prevent movement and vibration for reliable operation. It's a simple replacement part that restores proper fit and stability. What it does:

• Secures and supports nearby components or assemblies to prevent shifting
• Reduces vibration and rattling that can cause noise or wear
• Helps maintain correct alignment for connected parts to operate smoothly
• Restores original component retention after damage or loss of the bracket

• Disconnect power to the appliance before beginning any repair
• Basic hand tools may be required; handle small parts carefully to avoid loss
• Inspect surrounding clips and fasteners; replace any that are damaged

This is the rear tub drum for the washer's drum assembly; it supports the inner drum and helps keep loads balanced so the washer can tumble and spin properly. Use this part to restore stable drum rotation and reduce rubbing or banging noises. What it does:

• Supports the inner wash basket and maintains proper alignment during spin cycles
• Keeps the drum centered to prevent rubbing against the cabinet or seal
• Helps reduce loud banging, wobbling or excessive vibration during operation
• Works with the tub seals, bearings and suspension to maintain smooth rotation

• One rear tub drum

• Disconnect power and water before beginning any repair
• This is a major drum component; expect to remove the outer cabinet and other assemblies to access it
• Support the inner drum while separating components; bearings, seal and hardware may need inspection or transfer

Complete dryer door assembly that mounts to the front panel. Replace if your door is cracked, broken, warped, or won't seal properly against the frame.

Decorative guard panel for dryers. Covers and protects internal components while providing a finished appearance. Replace if cracked, broken, or missing.

Dryer won't start or stops mid-cycle? This door strike hook secures the door latch, engaging the switch so cycles can begin and run properly.

This frame assembly is the outer trim that surrounds the appliance door, restoring appearance and securing the door components for a finished, stable fit. It helps prevent gaps and keeps the door edges aligned. What it does:

• Replaces a cracked, warped, or damaged outer door frame that can affect door fit and appearance
• Restores a flush seal around the door edge to reduce light/air gaps and improve closure
• Provides the mounting surface for door components and retains their alignment
• Helps return the appliance to factory appearance after panel or glass replacement

• Disconnect power to the appliance before beginning any repairs
• Handle glass and trim carefully to avoid damage or injury; wear gloves and eye protection
• Basic hand tools (screwdrivers) are typically required; follow the OEM service manual for disassembly/reassembly

Fix a dryer door that won't stay closed or pops open with a new door hinge. Restores smooth pivoting and proper alignment. Basic DIY repair.

Dryer door sagging, rubbing, or won't close properly? This door hinge restores smooth opening and secure latching. Straightforward 15-minute fix.

Mounting bracket that secures and stabilizes the dryer door hinge assembly. Replace if cracked, broken, or causing door misalignment and sagging.

Secures the door hinge assembly to the cabinet for proper door support and alignment. Replace when the hinge area is cracked, worn, or damaged.

Replace your dryer's worn, cracked, or broken door handle. Restores secure grip for opening and closing. Direct fit for original mounting points.

Replace your broken or cracked dryer door handle assembly. Installs on the outer door panel for smooth opening and closing. Ideal for worn handles.

Frame assembly for dryers. This structural component forms the main support structure of the dryer cabinet. Replace if cracked, damaged, or worn.

This door gasket forms a watertight seal between the appliance's tub opening and the door, keeping wash water contained during operation. Replacing a worn seal helps stop leaks and protects floors and nearby cabinetry. What it does:

• Creates a tight, water-resistant seal around the door opening
• Replaces a torn, cracked, flattened, or deformed gasket that can leak
• Common symptoms: drips from the door area, puddles at the front corners, visible damage or mildew on the seal
• Restores proper door compression and helps prevent moisture/steam from escaping

• 1 door gasket

• Disconnect power and turn off the water supply before servicing
• Remove the old gasket and thoroughly clean the channel and mating surfaces
• Seat the new gasket evenly; ensure it is fully pressed into its channel (some models use retaining bands or clips—transfer and reinstall as removed)
• Close the door to check for uniform contact, then run a short cycle to verify no leaks

Fix loose wiring or unstable electrical connections in your dryer with this connector bar. Secures and routes wiring to keep components aligned. Easy install.

Vertical connector bar for dryer drum assembly. Replace if cracked, bent, or broken. Structural part that connects vertical components inside cabinet.

This replacement locker handle restores a secure grip and reliable latch operation on the appliance door or access panel. It replaces a cracked, loose, or missing handle so the door opens and closes smoothly. What it does:

• Provides a firm handhold for opening and closing the door or access panel
• Secures the door latch area to help maintain proper closure
• Replaces broken, cracked, or worn handles that are hard to grip
• Helps reduce rattling or loose-feeling door operation

• One locker handle

• Disconnect power to the appliance before beginning any repair
• Remove any trim or access panels as needed; use basic hand tools
• Handle may attach with clips or screws — keep hardware organized for reassembly
• Test door operation after installation; if fit feels incorrect, check part number and orientation

Fix a dryer door that won't latch or stay closed with this door hook locker. Simple repair that restores proper door closure in about 15 minutes.

Fix dryer drum rattling or misalignment with this coil spring. Essential suspension component for smooth operation. Moderate DIY repair in 30-45 minutes.

Cover cap for dryers. Installs on the dryer cabinet or control panel to conceal screws or openings. Replace if cracked, broken, or missing.

Small trim cap that snaps over exposed screws and mounting holes on your dryer. Replace if cracked, broken, or missing to restore a clean finish.

This customized screw secures appliance panels and components for a reliable fit, helping maintain proper alignment and reduce vibration or rattling. Designed as a direct replacement to restore original fastening where the correct screw is required. What it does:

• Fastens panels, brackets, or components to prevent movement and vibration
• Restores secure mounting when a screw is missing, stripped, or damaged
• Helps stop rattling or intermittent contact caused by loose hardware
• Matches the OEM style for correct fit and function when replacing a lost or worn fastener

• Disconnect power to the appliance before performing any repairs
• Use the proper screwdriver or driver bit to avoid stripping the screw head
• Do not overtighten; snug until secure to avoid damaging threads or components
• Keep small parts away from children and pets during installation

Secures and supports dryer panels and structural components to restore proper alignment. Replace if cracked, broken, or worn to stop panel rattling.

This replacement cap for a dryer restores the original protective cover that secures and seals drier components, helping keep lint and debris out and maintaining normal operation. Use it when the original cap is cracked, missing, or damaged. What it does:

• Covers and protects internal dryer components from lint and debris buildup
• Helps maintain proper airflow and reduces risk of trapping lint in moving parts
• Prevents loose parts from rattling or causing vibration-related noise
• Common symptom: visible cracks, missing cap, excessive lint accumulation, or unusual rattling

• Disconnect power (and gas supply for gas models) before starting any repair.
• Basic hand tools may be required; handle plastic parts carefully to avoid damage.
• Reassemble panels and verify operation; inspect for proper fit and clearance.

Fix loud banging, grinding noise, or poor drying performance with a new dryer blower wheel. Restores proper airflow through drum and exhaust vent.

Adapt your gas dryer for propane with this LP conversion kit. It provides the correct orifice and regulator adjustments needed so the burner fires properly on LP fuel, helping ensure safe operation and consistent drying performance after a fuel change.

• Converts a compatible gas dryer from natural gas to liquid propane (LP)
• Helps ensure proper burner flame characteristics on LP
• Appropriate when moving to a home with propane or changing utilities
• Symptoms can include weak heat, improper flame, or sooting

• Disconnect power and shut off gas before servicing
• Installation and regulator/orifice adjustments must be performed per the service manual
• After installation, leak-check all connections and verify proper burner operation
• Do not attempt conversion without the correct kit for your specific model

Blower housing assembly for dryer that channels heated air from the drum to the exhaust. Replaces a cracked or damaged housing to restore proper airflow and help the dryer dry more efficiently and quietly. What it does:

• Channels heated air from the drum to the exhaust and supports the blower wheel.
• Restores airflow when a damaged or cracked housing is restricting ventilation.
• Commonly used to address reduced drying performance and longer dry times.
• Can also resolve unusual rattling or grinding noises coming from the lower front of the dryer.

• Disconnect power (and gas, if applicable) before beginning work; wear eye protection and gloves.
• Remove access panels and disconnect vent/ducting per your model's service instructions to reach the blower housing.
• Inspect the blower wheel and surrounding seals/gaskets while the housing is out; replace damaged components as needed.
• Reassemble all panels and venting securely and test the dryer for proper airflow and operation after installation.

Duct assembly channels air from dryer drum to blower and exhaust. Replace if cracked, warped, or missing to restore proper airflow and prevent lint bypass.

This guide assembly is a replacement slide guide that helps support and align moving components for smooth operation and reliable engagement. It restores proper tracking and reduces wobble or binding in the mechanism. What it does:

• Provides stable support and alignment for a sliding component to prevent mis-tracking and uneven movement
• Reduces noise, sticking, or binding caused by worn or damaged guides
• Helps maintain proper clearance and engagement of the moving part
• Matches OEM fit and mounting points for direct replacement

• Turn off and unplug the appliance before beginning any repair to avoid electrical shock
• Remove any obstructing panels or components to access the guide
• Inspect mating parts (slides, rails, fasteners) and replace any damaged hardware to ensure correct fit

This adjustable leveling leg screws into the dryer base to support and stabilize the cabinet. Replacing a worn or missing foot helps level the appliance, reduce vibration and noise, and keep it steady on uneven floors.

• Provides threaded height adjustment to properly level the dryer
• Stabilizes the cabinet to minimize rocking, vibration, and walking
• Replaces a broken, worn, or missing foot
• Common symptoms: dryer wobbles, is hard to level, or makes rattling/vibration noise

• Disconnect power; shut off gas supply for gas models
• With a helper, carefully tilt or raise the dryer for access
• Unscrew the old leg; thread the new leg into the base by hand, then adjust with a wrench until the dryer sits level and stable
• Ensure all legs contact the floor and the dryer does not rock

Dryer holder clip secures components in place during operation. Replace if broken, loose, or missing to prevent rattling and ensure proper part alignment.

The Dryer Thermistor is an OEM part for LG dryers, designed to monitor and help regulate the temperature within the dryer by providing feedback to the control board about the temperature inside the drum. This allows the dryer to adjust its heat settings accordingly, preventing overheating and ensuring clothes are dried evenly and safely.

Symptoms of a bad Dryer Thermistor include:

• Clothes not drying properly or taking longer than usual to dry.
• The dryer repeatedly stopping during a cycle.
• Error messages appearing on the dryer's display panel.
• The dryer getting too hot or not heating enough.

Causes of a bad Dryer Thermistor can include a buildup of lint and debris affecting its ability to accurately sense temperature, wear and tear over time, or electrical issues within the dryer's circuitry.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Dryer Blower Thermostat is an OEM replacement part for LG dryers. It plays a role in regulating the operation of the blower motor, which is responsible for circulating hot air throughout the dryer during the drying cycle.

Causes of a bad dryer blower thermostat can include electrical malfunctions, physical damage, or simply wear and tear over time.

Symptoms of a bad dryer blower thermostat include:  

• The dryer not heating up properly or taking longer to dry clothes
• The blower motor failing to turn on or running continuously
• Inconsistent or inadequate airflow during the drying cycle
• Error codes or fault indicators related to the thermostat or blower motor

This OEM LG part is also compatible with Sears/Kenmore models.

Protective cover shields internal wiring and electrical terminals in your dryer. Replace if cracked, broken, or missing to prevent accidental contact.

Safety cover cap for dryers and laundry centers. Protects internal components and covers exposed areas. Replace if cracked, broken, or missing.

Fix dryers that won't start, stop mid-cycle, or display error codes with this wire harness assembly. Connects control board to motors and sensors.

The Motor Bracket is an OEM part for LG dryers. This bracket securely holds the dryer motor in place. It maintains proper alignment and spacing of the motor to allow for smooth operation of the tumble cycle.

Causes of a bad motor bracket can include cracks or breaks developed over time from repeated use and vibration, or damage due to impact or improper installation.

Symptoms of a bad motor bracket include:

• Excessive noise or grinding sounds emanating from the motor area
• The dryer not rotating or tumbling clothes properly
• Increased movement or shaking of the motor
• Poor airflow and inefficient drying performance

This OEM LG part is also compatible with some Kenmore models.

Hardware screws and nuts for installing a dryer side vent kit. Replace missing or stripped fasteners when reconfiguring exhaust outlet direction.

The Drum Motor Assembly is an OEM part for LG dryers. It serves as the powerhouse that drives the drum, enabling it to tumble clothes during the drying cycle. This essential component ensures your dryer operates smoothly, providing the necessary torque for consistent and efficient drying performance.

Causes of failure might include wear and tear from prolonged use, overload from trying to dry heavy loads, electrical issues like short circuits, or physical damage to the motor components. 

Symptoms of a bad Drum Motor Assembly include:

• The dryer drum fails to turn, even though the dryer powers on.
• Unusual noises, such as humming or buzzing, indicating the motor is struggling.
• The dryer stops unexpectedly during cycles or won't start at all.
• Decreased drying efficiency or clothes taking longer to dry due to inconsistent drum speed.

This OEM LG part is also compatible with Sears/Kenmore.

This clamp secures hoses, tubing or wiring to the appliance frame to help prevent rubbing, vibration and routing issues. It restores a solid attachment point so lines stay in place during normal use. What it does:

• Holds a hose, tubing or wire bundle in place to prevent chafing and abrasion
• Keeps components routed away from moving parts and hot surfaces
• Reduces rattling or vibration caused by loose lines
• Helps maintain safe, reliable connections by preventing strain on fittings

• Disconnect power and shut off water before servicing
• Use basic hand tools; avoid over-tightening which can pinch hoses or wires
• Inspect adjacent hoses/wires for wear and replace if damaged
• Take photos before removal to ensure correct reinstallation

This micro switch is a compact, snap-action electrical switch that sends an on/off signal when a lever, latch, or paddle is moved. Replacing a worn switch restores reliable detection and control response for the affected function.

• Converts mechanical movement into an electrical open/close signal to the control
• Commonly used for lever/paddle actuators, latches, or interlock detection within the appliance
• Safe symptom clues: no response when actuated, intermittent operation, or a function stuck on/off
• Physical clues: weak or absent "click" when pressed, heat discoloration or damage at terminals

• Disconnect power before servicing; if the product is connected to a water line, close the supply valve
• Note wire positions and terminal labels (COM/NO/NC); transfer wires one at a time to matching terminals
• Match the actuator orientation and mounting position to the original for proper operation
• After installation, verify continuity with a multimeter and test function before reassembly

Maintains tension on your dryer's drum belt for smooth rotation. Replace if pulley wheel is cracked, shaft worn, or assembly moves excessively during operation.

Idler pulley maintains tension on the dryer belt. Replace if worn, cracked, or causing belt slippage. Installs between motor and drum support system.

This replacement screw secures appliance components in their proper position. Use it to restore a tight, rattle-free fit when the original fastener is missing, stripped, or corroded. What it does:

• Fastens brackets, panels, or trim to keep assemblies aligned and secure
• Helps prevent vibration, rattling, and gaps from loose hardware
• Restores proper attachment when a screw is lost, worn, or damaged
• Common symptoms: loose panel/handle, misalignment, rattling, or a missing screw

• Disconnect power; shut off water or gas before service
• Match location to the original; start threads by hand to avoid cross-threading
• Use the correct driver bit; do not overtighten (especially into plastic)
• If the original hole is stripped, repair threads before installing the new screw

Self-tapping screw secures panels, brackets, and components inside your appliance. Replace stripped, corroded, or missing screws to restore secure fit.

Stationary platform that sits inside the dryer drum to hold shoes, delicates, and other items in place during air drying. Replaces damaged or missing racks.

This connector nozzle attaches to the appliance's nozzle assembly to route fluid through the system and help maintain a sealed connection. It replaces a worn or cracked nozzle connector to restore proper flow and reduce leaks. What it does:

• Provides a secure connection point for the nozzle assembly, directing fluid through the correct pathway
• Restores a sealed joint to prevent drips or steady leaks at the nozzle area
• Helps eliminate flow interruptions caused by a cracked, split, or damaged connector
• Works as a direct-fit replacement when the original connector is broken or degraded

• One connector nozzle

• Turn off power and shut off the water supply before starting any repair
• Remove only the components necessary to access the nozzle area; use basic hand tools
• Check seals and adjoining hoses for wear and replace if needed to ensure a leak-free connection

Dryer not steaming or refreshing clothes? This water inlet valve controls the steam cycle. Fixes mineral buildup and flow issues. Moderate DIY repair.

Accessory assembly for dryers. Installs on the exterior or interior to provide additional functionality. Replace if cracked, broken, or missing.

Fix leaks or poor water flow with a new washer inlet hose. This part channels household water supply into your machine for proper filling and operation.

This pipe connector joins appliance water tubing to the inlet assembly, restoring a secure, leak-resistant connection so the dispenser or ice-making system can get a steady water supply. Ideal when fittings are cracked or worn. What it does:

• Creates a watertight connection between supply tubing and the appliance inlet/valve
• Stops leaks caused by cracked, split, or loose fittings at the tubing junction
• Restores proper water flow to dispensers and ice makers when a bad connector is the cause
• Helps prevent water pooling and potential damage from slow leaks

• Turn off water supply and disconnect power before replacing the connector
• Inspect tubing ends for damage and trim squarely if needed before installing
• Use correct tools and tighten fittings per manufacturer guidance; do not overtighten
• After installation, restore water and power and check carefully for leaks

If your washer won't fill with water or leaks during fill cycles, a damaged inlet hose is often the cause. This hose restores proper water flow.

The Venting Kit is an OEM part for LG dryers. This part offers flexibility and efficiency in dryer installation and setup, this kit enables side or bottom venting of the appliance, facilitating optimal use of space in your laundry area. It's ideal for situations where the traditional rear venting is not feasible or preferred. 

Causes of venting system issues can include blockages, incorrect installation, or the use of incompatible parts, leading to reduced efficiency and potential safety hazards, such as overheating or fire risks.  

Symptoms of a bad or improperly installed venting system include:

• Extended drying times
• Excessive humidity or heat in the laundry area
• Unusual noises during operation
• Accumulation of lint in and around the dryer

This OEM LG part is also compatible with some Kenmore models.