Craftsman Chainsaw Parts

This chainsaw fuel cap assembly is made from high-quality plastic. Durable threads keep this chainsaw fuel cap assembly working for years of use. You place one end in the fuel tank while the screw cap covers the nozzle. This keeps your gas from spilling out and causing possible damage or injury. You can’t cut down a tree or slice up some firewood with gas leaking everywhere. This also leads to harming the environment around you. Chainsaws fuel caps can swell. The rubber seals may leak after a certain amount of use. The cord attaching the cap to the insert may break, allowing the cap to be lost. Replacing the chainsaw fuel cap assembly can correct these problems. Pliers or a wrench may be needed to remove the old fuel cap assembly. This genuine OEM chainsaw fuel cap assembly was manufactured for use with Craftsman chainsaws. It is also compatible with Poulan and Poulan Pro chainsaws.

This air filter is a genuine MTD part, sold individually. This air filter can be used as a replacement part for a chainsaw. The purpose of an air filter for a chainsaw is to block out debris from entering the interior workings of the appliance, which can protect the small engine from damage over time.The air filter of a chainsaw might have to be replaced at some point during the standard lifespan of the appliance if the component is punctured, torn, ripped, scraped, eroded, or otherwise damaged. If external materials can easily pass through the air filter from general wear and tear with long-term use or as the direct result of a collision, the component should be removed and replaced by this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.This is an OEM part sourced directly from the manufacturer. It is sold individually. This air filter is compatible with the following outdoor appliance brands: MTD and Craftsman.

The clutch connects to the crankshaft of the chainsaw engine. The crankshaft turns the up and down motion of the pistols into a rotation, which turns the drum and makes the chain go around. As the inner drum of the clutch starts to wear out, it puts more and more pressure on the springs, causing them to break. So, without a properly functioning clutch, the engine will run, but the blade will not turn. Replace the chainsaw clutch assembly using our genuine OEM part sourced directly from the manufacturer. A socket wrench and a screwdriver will be needed. Start by removing the chain brake cover to gain access to the clutch. Remove the chain and bar and then bind the piston in place. From there, use a screwdriver to remove and replace the clutch. This part is compatible with Poulan or Craftsman brand products. Sold individually.

This is an OEM replacement starter pulley kit designed for use with gas chainsaws. The starter pulley assembly replaces the components of your recoil starter that may fail due to normal wear and tear. The pulley and return spring react to the pull of the starter rope and then engage the flywheel. This is what fires the chainsaw engine. If the starter rope is not reacting or the flywheel is not engaging, there may be an issue with the starter pulley assembly. This repair can be completed with a screwdriver and pliers and doesn’t take a lot of time. This starter pulley kit is a genuine product from Husqvarna, and it is designed for use with Poulan, Jonsered, and Husqvarna engines and outdoor power equipment. This kit includes the plastic pulley, return spring, hub, and two screws for securing the unit. The housing, rope, and starter grip will be sold separately if replacements are needed.

This is a replacement chain brake that is designed as an identical part for select chainsaws. The chain brake is a safety component that covers the bar connection and helps to prevent injuries due to broken or loose chains. This piece is exposed to a lot of potential impact damage and debris, which can affect how well it works. The cover can become cracked or otherwise damaged. Without the chain brake cover, the saw will be unsafe to operate. In some cases, models may not operate at all until the chain brake is replaced. This genuine part will provide an exact fit for compatible saws. This OEM chain brake is manufactured by Poulan and compatible with more than 60 chainsaws from Poulan and Husqvarna. The chain brake is a high-quality part that is made of durable metal and plastic and it is sold as an individual piece. The hardware to install this part is sold separately. It is important to install the chain brake with the appropriate hardware and using the right tools so that it can be engaged to stop the chain in the event that it breaks or comes loose. Always disengage the spark plug or disconnect the power supply before performing equipment repairs.

Combustion engines operate because of the chambers that seal in the tiny explosions caused by fuel, air and a spark. The pistons are part of the process of taking power from those explosions, and the piston rings seal the combustion chamber so that all of the gases created remain inside of the engine's crankcase. This replacement piston ring will ensure that a chainsaw's engine can do that, as well as maintaining the right amount of oil between the piston and the cylinder wall. An OEM replacement part, this piston ring works with Craftsman and Husqvarna chainsaws, among others. It will require a wrench set, screwdriver and a pair of pliers to make the replacement. Sold individually.

Chainsaws generate a great deal of heat and friction, but the oil pump systems that keep the situation under control. They do this through the use of chainsaw bar oil poured into a reservoir. It remains in the reservoir until the throttle is engaged which then cues the pump to spray oil out of a port and smear it on the bar and chain to reduce friction and heat. The use of the oil pump is crucial, and this OEM oil pump assembly is a full replacement for times when a chainsaw is not getting adequate oil on the bar. It works with Poulan, Craftsman, Poulan Pro, and others. This project requires only wrench and screwdriver sets to perform the repair. It ships as an individual kit ready for full replacement of the original oil pump.

This part is a replacement engine pulley. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part can be used to replace a broken, defective, or damaged engine pulley on lawn mowers.The engine pulley is what drives the equipment's transmission belt. If this pulley is worn or malfunctioning, the blades of the mower or tractor will not rotate properly, if at all. Thus, this part should be replaced in order for the equipment to function properly. It's important when working on or near an engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this engine pulley, the appropriate owner's manual and equipment diagrams should be utilized.As an authentic replacement part, this engine pulley is suitable for use on several models of lawn mowers and lawn tractors manufactured by Husqvarna, Poulan, and other brands. This is a genuine part made of high-quality, durable materials and is sold individually.

This spark plug is a genuine MTD part, sold individually. This deck assembly can be used as a replacement part in a chainsaw. The spark plugs ignite when supplied with a mixture of fuel and air, powering the equipment.If the spark plug has been damaged due to exposure to the elements, general wear and tear, or an accidental collision with a hard object, it should be removed and replaced by this genuine OEM replacement part in accordance with the proper set of instructions sourced from a relevant appliance manual or handbook.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This spark plug is compatible with the following outdoor appliance brands: MTD and Craftsman.

This replacement part is a fuel filter. This is a genuine replacement part made by MTD. This fuel filter is responsible for ensuring that the fuel in the tank stays clean from debris and other objects that might enter the area. A new fuel filter might be needed if there is dirt, debris, or other objects in the fuel tank. This can mean that the fuel tank is no longer effective and should be replaced. Work gloves are recommended during this repair as fuel might stain the hands during the job. Be sure the engine is completely turned off before attempting to start this repair. This fuel filter is also sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use.

This part is a replacement screw. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part can be used to replace a defective or misplaced screw in a variety of lawn equipment. This screw is a high-quality piece of standard hardware with multiple different uses. Screws are essential for securing parts of the equipment, but can easily become lost, stripped, or otherwise damaged. If screws are missing, it can affect the functionality of the equipment. A Phillips head or flat head screwdriver can be used to install this screw. It's important when working on or near any engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this screw, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this screw is suitable for use on several models of lawn equipment manufactured by Husqvarna, Poulan, and other brands. This is a genuine part made of high-quality, durable metal and is sold individually.

This is a genuine OEM lawn and garden equipment screw that is used in various types of machines. It is a tapping screw that may have several applications depending on the exact equipment in question. A hex key screw is responsible for providing a secure hold for various components. It is made of durable metal, but also exposed to high heat and constant vibrations which can lead to wear, damage, or even breaking. The screw should always be replaced with an OEM replacement. This genuine OEM tapping screw is manufactured by Poulan. It is designed to be used in select outdoor power equipment units from the brand. It can also be used in compatible models from Paramount, Weed Eater, Jonsered, and Husqvarna. It fits trimmers, chain saws, and hedge trimmers from these brands. The tapping screw is sold individually and does not include any additional hardware or parts. A Torx screwdriver or hex key will be required to replace this tapping screw. Be sure to wear gloves when performing engine repairs and allow the machine to cool completely before starting work.

This is a replacement chainsaw retaining ring. The sprocket is commonly attached to the gear drive shaft in chainsaws with a retaining ring. If the original retaining ring becomes damaged, the chainsaw will not operate properly.Needle-nose, snap ring, or retaining ring pliers may be required to remove the old, damaged retaining ring. To install the new retaining ring, snap ring or needle-nose pliers should be placed into the small holes located on the new retaining ring. Then, slightly open the pliers to pull back the retaining ring's arms, opening up the ring center. Careful attention should be paid while opening the retaining ring to avoid overstretching. Overstretching the retaining ring would lead to the sprocket not correctly attaching to the chainsaw's gear drive shaft. Finally, with proper sizing, the retaining ring can be placed over the wheel grove, attaching the sprocket to the drive shaft.This retaining ring is an OEM part that is sourced directly from the manufacturer. This retaining ring is designed to replace damaged rings in Poulan, Poulan Pro, Husqvarna, and Craftsman chainsaws. The retaining ring is sold individually.

Carburetors mix fuel with air to ensure the engine gets just the right amount of combustion. It works when idling and when in operation, and a chainsaw carburetor requires an adapter. This reduces vibration to the carb and isolates heat to help keep the carburetor cool. This carb adapter kit will connect the carburetor to the cylinder and uses a gasket on either side that can fail and require replacement. Because plastic can be used for a carb adapter, it can crack and lead to failure. This OEM carb adapter kit is meant for Craftsman, Poulan and Husqvarna chainsaws, and will work in many different models. Replacing it will require the use of a wrench set, socket set, pliers, and screwdriver. As noted, gaskets may also be needed, but this part is sold individually and includes only the chainsaw carb adapter.