Craftsman Chainsaw Parts

This is a replacement chainsaw retaining ring. The sprocket is commonly attached to the gear drive shaft in chainsaws with a retaining ring. If the original retaining ring becomes damaged, the chainsaw will not operate properly.Needle-nose, snap ring, or retaining ring pliers may be required to remove the old, damaged retaining ring. To install the new retaining ring, snap ring or needle-nose pliers should be placed into the small holes located on the new retaining ring. Then, slightly open the pliers to pull back the retaining ring's arms, opening up the ring center. Careful attention should be paid while opening the retaining ring to avoid overstretching. Overstretching the retaining ring would lead to the sprocket not correctly attaching to the chainsaw's gear drive shaft. Finally, with proper sizing, the retaining ring can be placed over the wheel grove, attaching the sprocket to the drive shaft.This retaining ring is an OEM part that is sourced directly from the manufacturer. This retaining ring is designed to replace damaged rings in Poulan, Poulan Pro, Husqvarna, and Craftsman chainsaws. The retaining ring is sold individually.

Carburetors mix fuel with air to ensure the engine gets just the right amount of combustion. It works when idling and when in operation, and a chainsaw carburetor requires an adapter. This reduces vibration to the carb and isolates heat to help keep the carburetor cool. This carb adapter kit will connect the carburetor to the cylinder and uses a gasket on either side that can fail and require replacement. Because plastic can be used for a carb adapter, it can crack and lead to failure. This OEM carb adapter kit is meant for Craftsman, Poulan and Husqvarna chainsaws, and will work in many different models. Replacing it will require the use of a wrench set, socket set, pliers, and screwdriver. As noted, gaskets may also be needed, but this part is sold individually and includes only the chainsaw carb adapter.

The clutch assembly is located in the clutch drum and connected to the drive shaft of the motor. This part is what allows the engine to idle without actually driving the cutter on lawn and garden equipment. The clutch is constantly engaged, so it can wear out over time and eventually need to be replaced. It may also become damaged in a direct impact or incident. If the clutch assembly fails, this could impact the ability of the engine to idle properly or even to remain running once it's started. This replacement part can offer an exact fit for compatible engines. This OEM clutch assembly is manufactured to high standards by Poulan and is designed to be compatible with various machines from Poulan, Weed Eater, Jonsered, and Husqvarna. The clutch assembly is a replacement part for various trimmers and pruners from the brands listed above. Replacing the clutch will require a wrench, screwdriver, pliers, and socket set. Be sure to cool the engine completely and wear gloves when doing repairs on lawn and garden equipment for safety.

This is an OEM replacement chainsaw bar plate for select brands and models of chainsaws. The chainsaw bar plate is responsible for holding the chainsaw guide bar in place and providing a secure foundation to reduce vibrations, while also spacing the bar from the chassis. The plate itself can become loose over time, or can even become damaged and lead to things like oil leaks from a loose chain. If the bar plate is in disrepair or not functioning correctly, it should be replaced immediately. this genuine replacement part can provide an exact fit for compatible saws. This OEM bar plate is manufactured by Poulan and will fit a number of chainsaws from the brand Craftsman, as well as those from Husqvarna and Jonsered. This durable part is made from high-quality metal and can be replaced with only a few tools. The plate is sold individually as a single unit. Hardware is not included and will have to be purchased separately if it is required. Always wear gloves and disconnect the spark plug before beginning repairs on chainsaws.

This part can be used to replace a deteriorating or leaking oil pick-up in chainsaws. An oil pick-up is essential for a smooth-running piece of equipment, as it supplies oil to the engine. Over time, oil pick-ups can become worn, which can cause leaks and prevent the engine from receiving the necessary supply of oil to operate properly. This part is manufactured from high-quality, durable plastic and non-corrosive metal. This assembly pick-up oil tank is a genuine OEM replacement part that has been sourced directly from the manufacturer. This replacement assembly pick-up oil tank fits various different models of Husqvarna and Poulan chainsaws. Please note this part is sold individually.

This replacement part is a trigger and lockout kit intended for use in chainsaws. This is a genuine replacement part made by Husqvarna. Trigger and lockout kids are situated next to the handle at the top of the appliance. This part is one method of protecting the user from anything that can be harmful when using a chainsaw. It is made of durable plastic and metal. A new trigger and lockout kit might be needed if the current one is damaged or broken in any way. It is not unusual for this part to require replacement after years of normal use. Be sure the appliance is completely powered down and cooled off before attempting to replace this part. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with chainsaws made by Husqvarna.

This replacement oil tank for a pole pruner or chainsaw is an authentic OEM replacement part. The inner workings of an engine consist of many moving parts. These parts are mostly made of metal and they thrash about against each other to produce and transfer energy. Engines use oil to lubricate these parts so that they do not rub and create friction as this would cause the engine to overheat. This oil tank lets operators quickly top up their engines with oil without having to take apart the inner mechanics. Oil tanks are made of durable reinforced plastic but it is still possible to bang, dent, or even puncture them. Should this happen, oil will leak from the tank and the engine will be starved of lubrication. For safety purposes, it is important to immediately replace a broken oil tank. To do so, use a wrench to remove the old tank and install the new part with the same bolts. This oil tank is compatible with Poulan and some Husqvarna appliances, and as a high-quality replacement part, it comes sourced from its original manufacturer. This part includes an oil tank and oil tank cap but it does not include an oil line.

This authentic OEM part is a replacement momentary switch meant for a chainsaw or edge trimmer. Also known as a kill switch, a momentary switch acts as a safety measure to immediately shut off the appliance's motor. If the user begins to lose control of the appliance, they can simply hit the momentary switch and the engine will disengage even if it is not currently in the off position. This helps to prevent accidents and bodily harm. When engaged, the engine requires a five second waiting period before it can restart. Over time and through repeated use, switches can naturally become worn out. They may also be damaged if knocked against something hard on accident. Replacing this switch will require a screwdriver to access the switch located in the handle of the appliance. Once accessed, the switch can easily be replaced by detaching the wires and inserting the new part. Be sure to follow the user's manual as this process will vary depending on the appliance. This part is sourced directly from its original manufacturer and will work with Poulan and Weed Eater appliances. This part ships individually.

This replacement part is a line guide, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. This line guide is small but aids in creating straight lines while cutting the grass in many different lawn mowers. A new line guide might be needed if the user notices the current one is not working properly. If the cutting lines of grass are not as straight as normal there might be an issue with the line guide inside of the machine. Be sure to wear working gloves while replacing this part as it is typically found near the blades of the appliance. This small part is sold as a single piece. This part is a genuine OEM part sourced directly from the manufacturer. Be sure to reference the specific owner's manual for more information on how to replace this part.

This is a tank cap assembly that is used on many models of chainsaws. It is located on the fuel tank and is designed to ensure all fuel stays within the container. A retainer is included with the tank cap assembly to prevent dropping the cap and allowing dirt and debris into the fuel tank. An O-ring is used to seal the cap in the proper position. Tank caps can be damaged or lost, which can lead to dirty fuel, so the part will need to be replaced.Before replacing the tank cap assembly, make sure the chainsaw is off and the engine is cool. Place the chainsaw on its side and unthread the original tank cap assembly if it is still present. Pull the retainer from the fuel cap. Replacing the cap requires no special tools, but a pair of work gloves can be helpful. Take the new tank cap assembly and place the retainer into the tank. Thread the new cap on and tighten it before use.This part is made to be compatible with Poulan and Craftsman chainsaws. This tank cap assembly is an authentic OEM part that is priced as an individual part. It is directly obtained from the manufacturer.

This replacement part is an insert transfer and is intended for use in a variety of lawn equipment. This is a genuine replacement part made by Husqvarna. Insert transfers are small but very important to many different appliances like chainsaws. These parts reduce friction inside of the motor and piston. Without this part the engine could become damaged.A new insert transfer might be needed if the user hears noises coming from the equipment that are not normal. If there is excess heat coming from inside the appliance this might also be the cause. It is common that insert transfers become stripped overtime due to normal wear and tear. Be sure the equipment is completely powered down and cooled off before attempting to repair an appliance. For more detailed instructions on how to install this specific part, see the owner's manual. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of lawn equipment made by Husqvarna.

This is a fuel filter and hose that fits several different models of chainsaw. It's located near the fuel tank and works to prevent dirt, debris, and water from entering the combustion chamber of the chainsaw. It removes the impurities that are in the fuel before any of them can reach the carburetor. If the filter is clogged, the hose is kinked, or either of the components is otherwise damaged, it will need to be replaced.A sputtering noise when starting the chainsaw could indicate that the fuel filter and hose are damaged. It can also cause difficulty starting, or uneven idling. If the problem is severe, the chainsaw may have little power while it is being used or might not turn on at all. When replacing this part, make sure the chainsaw is powered off and the spark plug has been removed. The fuel filter and hose can be removed from the fuel tank and replaced to get the chainsaw to run again.This fuel filter and hose is a genuine OEM replacement part directly sourced from the manufacturer. It comes as an individual part. It is designed to be used with compatible Craftsman and Poulan chainsaws.

This starter cup assembly is a genuine Husqvarna part, sold individually. This starter cup assembly can be used as a replacement part in a string trimmer. The purpose of the starter cup assembly in a string trimmer is to rotate the flywheel with the purpose of powering on the small engine of the string trimmer; the starter cup assembly is a key component of the pull-start mechanism of a string trimmer.If the starter cup assembly suffers from puncturing, tearing, scraping, cracking, denting, eroding, or warping to the point of reduced efficacy, the starter cup assembly should be removed and replaced by this genuine OEM replacement part. Always unplug the appliance before performing any kind of repair or replacement.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This starter cup assembly is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, Poulan, and Poulan Pro.

This genuine OEM replacement ignition module is a type of electric switch used to send signals to the ignition cable and create a spark to fire up the engine in a gas-powered chainsaw. When the ignition coil creates a high-voltage charge, it triggers the spark plugs to create a spark and ignite some fuel so the engine will start. The ignition is usually one of the first things to check if an appliance's engine does not start, after checking for fuel and then the spark plugs. If the spark plugs are fine, though, the problem is likely to do with another part of ignition, namely the ignition module. As it is located near a high-voltage region of the ignition, the switch can fry and will need to be replaced. Using a pair of pliers, a screwdriver, and a wrench set, switch out the faulty ignition module and test the engine to see if it starts. This replacement ignition module is compatible with Craftsman chainsaws and does not include any addition hardware. As a high-quality part, it comes sourced directly from the original manufacturer.