Crosley Gasket & Seal

Note: For faucet adapter

The Freezer Door Gasket is an OEM replacement part for Frigidaire refrigerators. It creates a seal around the freezer door to maintain a consistent temperature by keeping cold air in and warm air out. This helps ensure proper freezing conditions and prevents energy loss.

Over time, gaskets can degrade due to wear, exposure to extreme temperatures, or cleaning with harsh chemicals. A damaged or worn gasket may fail to seal properly, affecting the freezer's efficiency and potentially leading to increased energy consumption.

Symptoms of a bad gasket include:

• Frost or ice buildup inside the freezer
• Difficulty keeping the freezer door fully closed
• Warm air entering the freezer, causing temperature fluctuations
• Increased energy bills due to inefficient operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Seal is an OEM replacement part for Whirlpool dryers. It creates a tight seal between the dryer door and the drum, preventing heat and moisture from escaping during the drying process. It helps maintain the proper temperature inside the dryer, allowing your clothes to dry quickly and evenly.

Symptoms of a faulty door seal include:

• Heat escaping from around the dryer door
• Excessive moisture or lint buildup
• Extended drying times

A bad door seal can occur due to regular use, wear and tear, or accidental damage. If you notice issues such as heat escaping from around the dryer door, excessive moisture or lint buildup, or clothes taking longer to dry than usual, it may be time to replace the door seal.

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This replacement seal restores a tight barrier between mating parts in your appliance, helping contain moisture at the joint. A fresh seal prevents leaks and supports proper performance when the original is worn, cracked, or compressed. What it does:

• Creates a moisture-tight seal between components to contain water at the connection
• Helps prevent drips, pooling, or seepage around the joint
• Replace if the seal is cracked, torn, flattened, deformed, or brittle
• Symptoms can include dampness at the joint, small leaks, or a loose fit

• 1 seal

• Disconnect power and shut off water supply before servicing
• Note the seal's orientation during removal to ensure correct placement
• Clean and dry mating surfaces; remove old residue or debris for a proper seal
• Seat the new seal evenly without twisting; verify full, uniform contact before reassembly

The Gasket-FIP  is an OEM part for Whirlpool refrigerators, ensures an airtight seal around the door, preventing cold air from escaping and warm air from entering. This component contributes to the refrigerator's energy efficiency and cooling effectiveness, maintaining the optimal internal temperature to keep your food fresh longer. 

Causes of a bad Gasket-FIP can range from normal wear and tear, accidental damage, or deformation due to improper cleaning methods or exposure to extreme temperatures.  

Symptoms of a bad Gasket-FIP include:

• Noticeable gaps between the gasket and the refrigerator door or frame
• Condensation or frost buildup near the door edges
• The refrigerator working harder to maintain its internal temperature, potentially leading to increased energy bills
• The door not closing as smoothly or firmly as it should

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This refrigerator door gasket seals the door to the cabinet to keep cold air in and moisture out. Replacing a worn or deformed gasket restores a reliable seal, steadier temperatures, and more efficient performance.

• Creates an air-tight seal around the door perimeter
• Helps maintain correct temperatures and reduce frost or condensation
• Supports proper door closing and overall cooling efficiency
• Replace if the gasket is torn, cracked, warped, hardened, or leaves gaps; if the door pops open; or if you see moisture/frost along the door edge

• Disconnect power; remove items from the door bins for access
• Pull the old gasket from the retainer; transfer/loosen corner screws if applicable
• Warm the new gasket (hot water or low-heat hair dryer) to relax it; seat the lip evenly, corners first
• Close the door and check for uniform contact; adjust with gentle heat and by leveling/hinge alignment if needed; allow up to 24 hours for the gasket to fully conform

This refrigerator door gasket replaces a worn seal to restore a tight, even closure around the door. A proper seal keeps cold air in and moisture out, helping maintain temperature, reduce frost, and minimize run time. What it does:

• Forms a tight seal between the door and cabinet frame
• Helps maintain set temperatures and reduce moisture intrusion
• Resolves frost or condensation at the door and frequent compressor cycling
• Common signs: torn, cracked, or warped gasket; gaps; door not sealing smoothly

• Includes: 1 door gasket

• Disconnect power before servicing; remove or secure contents for safety
• On many models, loosen the inner-liner screws or pull the old gasket from the retainer/channel to remove
• Warm the new gasket (warm water or low heat from a hair dryer) to relax shipping folds
• Seat corners first, then press the rest into the retainer; verify seal with a paper-slip test and adjust as needed

This door gasket seals the refrigerator/freezer door to help maintain proper temperature and reduce energy loss. A direct-fit replacement that restores the magnetic seal for better cooling performance. What it does:

• Re-establishes a tight seal around the door to keep cold air in and warm air out
• Helps reduce frost buildup and moisture inside the compartment
• Improves cooling efficiency and may reduce excessive run time from a failing seal
• Stops drafts and prevents food spoilage caused by a poor door seal

• One door gasket

• Clean the door frame and remove old gasket before installing the new one
• Warm or flex the gasket as needed for easier positioning; ensure the magnetic seal seats evenly around the perimeter
• Check hinge alignment and door closing after installation to confirm a complete seal
• Follow appliance power-off and safety precautions; refer to the appliance manual for model-specific instructions

This evaporator cove seal is the replacement gasket that helps keep the evaporator compartment sealed for efficient cooling and proper defrost drainage. It restores the evaporator cove barrier to help maintain temperature consistency. What it does:

• Seals the evaporator cove to limit air exchange between the evaporator area and the fresh food/freezer compartments
• Helps direct defrost water to the drain path and reduce water pooling inside the appliance
• Reduces frost buildup and cold-air loss around the evaporator area
• Commonly replaced when you see frost/ice buildup, interior water leaks, or uneven cooling

• Disconnect power before starting any repair to avoid shock or injury
• Remove shelves/food and allow the appliance to defrost if ice is present before replacing the seal
• Inspect the evaporator cover and mating surfaces; clean and dry surfaces for a proper seal
• Seat the seal evenly around the cove; avoid overstretching or sharp tools that could damage the gasket