Crosley Gasket & Seal

Kit contains 2 pads, 1 right glide, 1 left glide, and instruction sheet. Support brace no longer included.

This gray door gasket restores a tight seal around the freezer door opening so cold air stays in and warm, humid air stays out—helping maintain proper temperature and reduce frost buildup when the original seal is worn or damaged. What it does:

• Seals the perimeter of the freezer door to prevent air leaks
• Helps minimize frost/ice accumulation and moisture around the door
• Supports consistent interior temperatures and performance
• Common signs of failure: tears, warping, gaps, frost buildup, sweating/condensation, and poor door sealing

• 1 gray door gasket

• Unplug the appliance before servicing
• Warm the new gasket (soak in warm water or gently heat) to relax folds for easier installation
• Install starting at the corners; ensure the gasket fully seats in the retainer all the way around
• After installation, check seal tension around the door; use low heat to help the gasket conform if needed

The Gasket is an OEM part for Frigidaire washing machines. This part is located between the front and rear outer tubs and prevents water leaks by maintaining a watertight seal between them. The gasket acts as a barrier to ensure that water used during the washing process remains contained within the inner tub, preventing it from seeping into the washing machine's surrounding components.  

Causes of a bad gasket can include regular wear and tear, exposure to harsh detergents, or deterioration over time.  

Symptoms of a bad gasket include:

• Water leaking from the outer tub area
• Visible cracks or deterioration in the gasket material
• The washing machine not holding water properly
• Increased noise or vibration during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Length: Approx. 82 1/2"

Right hand side. Used most Admiral, Crosley, Norge, and Magic Chef dryers. Includes glide and felt pad.

This door seal replaces a worn or damaged gasket around the oven door, creating a tight barrier between the door and the front frame. A fresh seal helps the appliance heat efficiently and maintain steady cooking temperatures. What it does:

• Seals the gap between the door and oven frame to minimize heat loss
• Helps the oven preheat faster and hold set temperatures more consistently
• Replace if the gasket is torn, brittle, flattened, or frayed
• Common signs include heat escaping around the door edge and longer cook times

• 1 door seal

• Disconnect power and allow the oven to cool completely before beginning
• Open the door and carefully remove the old seal, noting its routing and attachment points
• Clean the mating surface to remove debris for a proper seal
• Install the new seal evenly without stretching; ensure all ends and anchors are fully seated

This freezer door gasket replaces a worn or deformed seal to restore a tight, even closure on the freezer door. A proper seal keeps cold air in and humid air out, reducing frost buildup and temperature swings.

• Creates an air-tight seal between the freezer door and cabinet to contain cold air
• Helps maintain correct temperature and efficiency; reduces frost/ice around the door perimeter
• Symptoms of failure: tears, cracks, warping, gaps, or door not closing fully
• Presents as frost buildup, moisture/condensation, or warm spots in the freezer

• Disconnect power to the refrigerator before servicing
• Let the new gasket relax (lay flat; warm gently with hot water or a hair dryer) for easier fit
• Remove the old gasket from the retainer/channel; on screw-retained styles, loosen (do not remove) liner screws as needed
• Seat the new gasket evenly, starting at the corners; use gentle heat to smooth wrinkles and ensure a uniform seal all around

This tub cover seal fits between the outer tub and the tub cover/splash guard on compatible washers. It keeps wash water and suds contained, helping prevent leaks from the top of the cabinet during agitation and spin.

• Forms a watertight barrier between the outer tub and the tub cover/splash guard
• Helps prevent splash-over and top-rim leaks during wash and spin
• Maintains proper containment of water and suds inside the tub assembly
• Common failure signs: water leaking from the top area, wet streaks down the outer tub, visible cracks, hardening, or flattening of the seal

• Disconnect power and shut off water supply before servicing; wear gloves and eye protection.
• Access the tub cover per service instructions; release the retainer ring/clips to remove the cover and old seal.
• Clean and dry all mating surfaces; remove residue so the new seal seats evenly.
• Lightly moisten the new seal, install uniformly around the rim, reinstall the cover/retainer, and run a short test with water to check for leaks.

The door seal forms the primary gasket around the door opening on horizontal-axis machines, creating a tight barrier that keeps contents contained and prevents gaps that can lead to leaks, odors, and poor performance. What it does

• Seals the perimeter of the door opening to contain wash water and suds
• Helps the door close flush and maintain a consistent, leak-free seal
• Common symptoms: water leaking at the door area, visible tears or cracks in the seal, persistent mildew/odors around the gasket, or a door that won't seal properly

• 1 door seal

• Disconnect power and shut off water supply before servicing
• Remove the front panel/retaining bands as needed to access the seal
• Note orientation and drain holes at the bottom; press the seal fully into its groove all the way around
• Reinstall retainers, ensure the door closes flush, and run a short test to check for leaks

This coupler gasket creates a tight, leak-resistant seal at a coupler connection point, helping maintain proper operation of the assembly. Replace when the original gasket is worn, cracked, or flattened to prevent drips and seepage.

• Forms the seal between a coupler and its mating component
• Helps prevent water seepage and air intrusion at the joint
• Supports correct flow/pressure through the connection
• Common symptoms: drips at the fitting, moisture around the coupler, or needing to over-tighten to stop leaks

• Disconnect power and shut off water supply before servicing
• Relieve line pressure and place a towel to catch residual water
• Clean mating surfaces; seat the gasket squarely in the coupler recess
• Tighten fittings evenly; restore service and check for leaks

This sump gasket seals the connection between the dishwasher tub and the sump/pump assembly. Replacing a flattened or cracked gasket restores a watertight barrier to help stop leaks from the base and protect floors and cabinetry.

• Creates a seal between the tub and sump to contain wash water
• Helps prevent leaks during fill, wash, and drain cycles
• Replace if the gasket is cracked, brittle, deformed, or compressed
• Common symptoms: water under the dishwasher, dripping from the base, moisture around the toe-kick

• Disconnect power and shut off the water supply; pull the dishwasher out if needed for access
• Access the sump area (often by removing the lower rack, spray arm, and filters); note gasket orientation
• Clean mating surfaces; seat the gasket evenly without twists. Do not use sealants unless specified by the manufacturer
• Reassemble and run a short test cycle while inspecting for leaks

The Evaporator Cover Gasket seals the perimeter of the freezer's evaporator cover to prevent air leaks that can lead to frost, moisture, and temperature swings. Replacing a worn gasket helps restore proper airflow and consistent cooling.

• Seals the evaporator cover to the liner to maintain directed airflow and contain cold air
• Helps prevent frost or ice buildup around the cover and on nearby air passages
• Can help address symptoms like temperature inconsistencies, poor cooling, or excess moisture caused by air leaks
• Replaces a torn, flattened, or missing gasket to ensure a tight cover fit

• Disconnect power before servicing; wear cut-resistant gloves
• Remove freezer shelves/bins and the evaporator cover to access the gasket
• Clean mating surfaces; press the new gasket fully into place with no gaps or twists
• Ensure air vents are unobstructed, reinstall the cover securely, then restore power

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

Located between the console and door

This seal-damper is the gasket that fits around a refrigerator's air damper to help keep compartments properly separated and maintain intended airflow. Replacing a torn or compressed seal helps reduce uneven cooling and drafts. What it does:

• Seals the air damper opening to limit unwanted air exchange between compartments
• Helps maintain stable temperatures by preventing cold or warm air leakage
• Common symptom fix: reduces uneven cooling or warm spots near the damper area
• Also helps reduce excess frost or condensation that can form from persistent air leaks

• Disconnect power to the appliance before starting any repair and remove nearby food/shelves for access
• Access the damper housing per your model's service instructions, remove the old seal, and seat the new seal onto the damper frame or mounting groove
• Clean the mounting surface of debris or old adhesive so the new seal sits flat; use gentle pressure to fully engage the seal
• If the damper housing is cracked or the seal does not seat properly, replace the damper assembly.

This fresh food door gasket seals the refrigerator compartment door to keep cold air in and warm air out. Replacing a worn gasket restores a tight seal, improves temperature stability, and helps prevent condensation and frost around the door.

• Seals the perimeter of the fresh food (refrigerator) door to limit air leaks
• Helps maintain proper interior temperature and efficiency
• Typical symptoms of failure: door not closing or sealing fully; visible tears, gaps, or warping
• May cause moisture, sweating, or frost near the door gasket area

• Disconnect power before servicing
• Warm and relax the new gasket (soak in warm water or use low heat) to ease installation; do not overheat
• Clean the door's gasket channel; install starting at the corners and ensure even seating all around
• Close the door and check for uniform contact; use a paper-slip test to confirm the seal