Crosley Pump

The Filter Assembly is an OEM part for Whirlpool dishwashers. This component is responsible for trapping food particles and debris, preventing them from recirculating during the wash cycle and ensuring that dishes come out clean. 

Causes of a bad filter assembly can include accumulated debris, regular wear from repeated use, or damage from harsh cleaning agents. A compromised filter can reduce the dishwasher’s cleaning performance and lead to buildup inside the machine.

Symptoms of a bad filter assembly include:

• Dishes not being cleaned properly
• Unusual noises during the wash cycle
• Slow drainage or standing water in the dishwasher
• Visible damage or clogging of the filter

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Drain Pump is an OEM replacement part for Frigidaire front load washers. Located inside the base of the washing machine tub, it actively pumps out water through the drain hose after each cycle completion. Efficient drainage is vital for preventing standing water issues.

Causes of a bad drain pump can include mineral or scale buildup within the pump chamber or impeller over time. The water valve may fail to open fully, blocking drain flow. Bearings may wear, causing the impeller to jam.

Symptoms of a bad drain pump are:

• Incomplete water draining after the cycle
• An accumulation of water remaining in the tub
• Leaking from the base
• Error codes could indicate drainage problems.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore.

The Water Pump is an OEM replacement part for Whirlpool washing machines. It plays a crucial role in circulating water throughout the wash cycles and draining the used water from the tub.

Symptoms of a bad water pump include:

• Washer not draining properly, leaving standing water in the tub
• Loud grinding or humming noises during the spin or drain cycles
• Leaks around the pump or connected drain hose
• Error codes or indicators related to drainage or pump issues

Causes of a bad water pump can include clogs or obstructions in the pump impeller, worn-out pump seals or bearings, or electrical malfunctions preventing the pump from operating correctly. Foreign objects or debris can also contribute to pump failure.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This dishwasher wash impeller mounts on the circulation pump to drive water through the spray arms. A worn or damaged impeller can cause weak spray, poor cleaning, or noise; replacing it restores proper wash pressure. What it does:

• Moves water from the circulation pump through the filter and spray arms for effective cleaning
• Maintains proper wash pressure and spray action during the cycle
• Common fix for poor cleaning, spray arms not turning, or weak/no water circulation
• May reduce grinding or rumbling noises caused by broken or stripped impeller blades

• Includes 1 wash impeller

• Disconnect electrical power and shut off the water supply before servicing
• Remove the lower rack and spray arm; take off filters/sump cover to access the impeller
• Note impeller orientation; transfer any spacers as found and secure the impeller without overtightening
• Reassemble, check for leaks, and verify spray arm rotation after a test cycle

The Sump Cover and Filter is an OEM part for Frigidaire dishwashers. Located inside the bottom of the tub, it seals off and protects the drainage sump where debris collects after each wash cycle. The attached mesh filter screens out particles that could otherwise clog drain lines.

Causes can involve mineral buildup that blocks the filter mesh over time, cracks in the plastic housing exposing the sump, or a missing or damaged filter that fails to trap solids.

Symptoms of a bad sump cover and filter include:

• Standing water inside the bottom of the dishwasher tub
• Reduced drainage or water removal after cycles complete
• Floating debris trapped near the drain pump area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
 

This is a circulation pump motor for dishwashers. It controls the main pump of the appliance.The pump is directly responsible for removing extra water from the dishwasher after use. When a dishwasher's circulation pump motor goes bad, the main indicator is usually leaking from the appliance. There will be a noticeable amount of water emerging from the bottom of the machine whenever the cycle is engaged. Unplug the dishwasher from its main power source and water hookup. Remove the dishwasher from its space in the counter. Remove all necessary entry plates to access the interior of the dishwasher. There is a metal bracket holding the current motor in. Unscrew the two screws that secure the bracket and remove this component. Remember which way the motor is oriented before removing it. Unplug the power cable connecting the motor to the dishwasher. Put the two new sealing rings on the new pump motor. Repeat these instructions in reverse to install the new part.This Frigidaire dishwasher circulation pump motor is a genuine OEM replacement part sourced directly from Frigidaire. The pump motor is sold individually. This part is compatible with Frigidaire, Kenmore, Westinghouse, and Gibson appliances.

This drain pump assembly actively removes water from the washer tub during drain and spin cycles, helping prevent standing water and cycle interruptions. Replacing a worn pump restores proper draining and reliable cycle completion.

• Pumps water from the tub through the drain hose to the household drain
• Common symptoms: no drain or slow draining, water left in tub, cycle stops due to drainage issues
• May present with unusual pump noises (buzzing/grinding) or leaks at the pump housing
• Restores proper water evacuation to allow cycles to finish

• Unplug the appliance and turn off water supply before servicing
• Expect residual water—use towels or a shallow pan when removing hoses
• Access the pump (front lower or rear panel varies by model); disconnect wiring and hoses, and transfer any brackets/grommets from the old pump if needed
• Clear the drain filter, sump, and hose of debris; then test for leaks after installation

Seal included. This sump housing assembly includes a 32.17 millimeter hole for the thermistor. If the hole for the thermistor is 31-31.5 millimeters you will need to order WP8534882.

This replacement filter traps debris and contaminants within your appliance's system to help protect internal components and maintain proper performance. Swapping a clogged or damaged filter can restore flow/airflow, reduce odors and buildup, and support efficient operation. What it does:

• Captures grease, lint, dust, or food particles to prevent recirculation and protect internal parts
• Supports proper airflow or fluid flow for ventilation, circulation, or drainage
• Helps minimize odors and residue caused by a saturated filter
• Typical signs it's due: visible tears/warping, heavy buildup, restricted airflow/venting, lingering odors

• 1 filter

• Disconnect power before servicing and allow any hot surfaces to cool
• Note the filter's orientation and any tabs/clips; install the new filter the same way
• Clean the surrounding housing or channel before installation
• Do not operate the appliance without required filter(s); follow your model's maintenance schedule

This small check ball helps control water flow inside the refrigerator's water/ice system to prevent backflow and ensure proper filling. It restores reliable water seating where valves or distributor ports use a ball-style check. What it does:

• Acts as a one-way seal to stop water from flowing backward into the supply line or valve bore
• Helps the ice maker and dispenser fill correctly by allowing water in but not back out
• Common symptom: intermittent or incomplete ice maker fills
• Common symptom: slow or continuous dripping from dispenser or valve area

• Shut off water supply and unplug the appliance before starting
• Small part — handle carefully and note orientation/seat before removal
• Inspect valve bores and seals for debris; clean area before installing new check ball

The Volute with Seal is an OEM part for Whirlpool dishwashers. This part directs water flow within the dishwasher's pump, ensuring efficient circulation and pressure during the wash cycle. The seal helps to prevent leaks by maintaining a tight closure between the volute and other pump components.

Common causes of a bad volute with seal include wear and tear from regular use, damage from debris or hard water deposits, and seal degradation due to age or chemical exposure.

Symptoms of a bad Volute with Seal include:

• Water leaking from the pump area
• Decreased washing performance
• Unusual noises from the pump during operation
• Visible cracks or damage to the volute or seal

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement part is a dishwasher pump and motor assembly. The dishwasher pump and pump motor circulate water through the dishwasher's spray arm. When the spray arms aren't spraying properly, this could mean that it's time for a new pump and motor assembly. Luckily replacing this part is a relatively simple process.Start by making sure the dishwasher is unplugged. After that shut off the water supply going to the dishwasher. Then disconnect the drain line from the garbage disposal or sink drain. Open the dishwasher door and pull out the bottom dish rack. Remove the upper dishrack from its track. Release the spray arm on the bottom of the washer. Then proceed to release the feed tube clips. Using a nut driver remove the bottom access panel and tow panel. Pull them out to remove them. Remove the power cable from the junction box, and disconnect the supply line from the inlet valve. Proceed to pull the dishwasher out of the counter. Tilt the dishwasher on its side and pull the hose from the drain pump. Remove the wire harness from the pump. Disconnect wires from diverter motor and circulation motor. Once complete, proceed to tilt the dishwasher upright and remove the pump and motor assembly from the bottom of the dishwasher. Replace with the new assembly.This replacement part is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.

This chopper assembly replaces the food-chopping component in compatible countertop food processors, restoring even chopping and diced results. It helps get blades turning and keeps food processing performing as intended. What it does:

• Spins and chops food inside the processor bowl for consistent results
• Restores proper cutting when chopping is uneven or not happening
• Helps eliminate food buildup that causes noisy or inefficient operation
• Works with the existing drive coupling to transfer motor power to the blades

• Disconnect power and remove the processor bowl and lid before servicing
• Handle blades carefully — they are sharp; wear cut-resistant gloves
• Ensure the part seats fully on the drive coupling and locks into place before use
• Test operation with small amounts of food after reassembly; stop immediately if unusual noise or resistance occurs

Seal not included