Crosley Refrigerator Door Stop Or Cam Riser

This refrigerator door closer restores smooth, positive door action. When worn, the door can click, bind, or swing open. Replacing it helps the door seal properly to maintain temperatures and limit frost or moisture.

• Provides cam action at the bottom hinge for smooth opening and a positive close
• Helps pull the door shut during the last inches of travel to maintain gasket contact
• Typical wear symptoms: popping/clicking at the lower hinge, door that won't stay closed, or poor sealing
• Visual clues include flat spots, grooves, or cracks on the cam surface

• Disconnect power and remove items from the door for safety and to reduce weight
• Lift the door off the bottom hinge; transfer/install the closer in the same orientation as the original
• Reassemble, then verify the door self-closes and the gasket seals evenly
• Use care not to pinch or distort the door gasket during reinstallation

This door closer plate is a hinge component that helps your refrigerator door swing closed and seal properly. Replacing a worn plate restores smooth door action and supports a reliable seal to help maintain interior temperatures.

• Guides the hinge/cam for self-closing action and a consistent door stop
• Helps the door close fully and stay shut to protect the gasket seal
• Common symptoms include clicking/grinding at the hinge, door drifting open, or misalignment
• A weak seal from incomplete closing can contribute to frost or condensation

• Unplug the refrigerator; turn off the water supply
• Remove items from the door and support the door to prevent strain on the hinge
• Remove hinge cover and fasteners, separate the hinge as directed by your manual, and replace the closer plate; align with the mating cam
• Reassemble, level/align the door, and verify smooth closing and gasket contact

This hinge bearing supports the freezer door on the hinge pin so it swings smoothly and stays aligned. Replacing a worn bearing can stop scraping or sagging and help restore proper door movement and sealing.

• Provides a low-friction surface between the hinge pin and door
• Helps maintain correct door height and alignment for a reliable seal
• Wear symptoms include squeaking/scraping, door drop or wobble, and difficulty closing
• Replace if the original bearing is cracked, flattened, or missing

• Disconnect power and remove items from the freezer door before starting
• Support the door; remove hinge cover and fasteners, then lift the door off the hinge pin
• Slide the old bearing off the hinge pin and install the new bearing in the same orientation
• Reassemble, then check door alignment and gasket contact; adjust as needed

This white door stop limits how far the door swings open, helping protect hinges and nearby surfaces. Replace a worn or missing stop to restore the intended opening range and smooth, controlled door movement.

• Limits door swing to prevent overextension and impact
• Helps protect door hinges and surrounding cabinetry
• Restores proper opening range when the original stop is cracked or missing
• Common signs: door opens too wide, door hits adjacent surfaces, visible broken/missing stop

• Disconnect power and clear items from the door before service
• Support the door to prevent strain on the hinges
• Remove hinge cover and fasteners as needed, swap the stop, and reassemble
• Open and close the door to verify proper swing and gasket seal

This door stop replaces the small bumper that cushions and limits the door's travel so the door closes smoothly and avoids hard impacts. It restores normal door movement and reduces noise from slamming or catching. What it does

• Acts as a bumper/stop to limit how far the door opens or closes
• Cushions the door to prevent hard impacts and reduce noise
• Helps keep the door aligned and prevents catching or uneven closing
• Commonly replaced when the stop is worn, cracked, missing, or deformed

• One door stop

• Disconnect power (unplug or switch off breaker) before starting any repair
• Removal/installation typically requires basic hand tools and access to the door hinge/stop area
• Align the new stop in the same position as the old one and secure per the appliance's hinge/trim layout
• Reuse the original fasteners unless replacements are specified

This door closer with cup mounts on the hinge to control the door's final closing motion. It restores smooth, consistent closing and helps the gasket seal evenly to maintain proper temperatures.

• Provides hinge cam action that pulls the door closed during the last few inches
• Helps keep the door aligned so the gasket seals evenly around the cabinet
• Reduces slamming and prevents the door from drifting or popping back open
• Common symptoms of wear: clicking/grinding at the hinge, sagging or rubbing, poor self-closing, or moisture/frost near the door

• Unplug the refrigerator and remove items from the door to reduce weight
• Support the door; remove hinge cover and fasteners, then lift the door off to access the closer components
• Match the original orientation; install the new closer and cup on the hinge/door seats
• Reinstall and align the door; tighten hinge screws and verify smooth self-closing and gasket contact