Crosley Refrigerator Hinge Parts

This hinge supports and pivots the washer lid so it opens and closes smoothly. Replacing a worn or broken hinge restores proper alignment and helps the lid close securely without binding or rubbing.

• Provides the pivot point for the lid to open and close
• Keeps the lid aligned with the top panel
• Wear symptoms include wobble or sagging, squeaks, binding, or visible cracks/bending
• Misalignment may prevent the lid switch/latch from engaging properly

• Unplug the washer before servicing; have a helper support the lid
• Remove the mounting screws, noting hinge orientation for reassembly
• Transfer and reuse original screws/trim as applicable; do not overtighten
• Test lid alignment and operation before fully tightening the fasteners

This lower hinge bracket mounts at the bottom of the cabinet to support and align the refrigerator door. Replacing a bent or worn bracket helps restore smooth door operation and a consistent gasket seal to help reduce air leaks.

• Provides the mounting base for the lower hinge/pin at the bottom of the cabinet
• Supports the door's weight to keep it level and properly aligned
• Helps the door open and close smoothly without scraping or binding
• Typical symptoms: door sagging or misalignment, difficulty closing, gaps at the gasket, squeaks/scraping near the lower hinge, or visible bracket damage

• Disconnect power; remove items from the door and support the door to prevent dropping
• Mark hinge/bracket locations for alignment; remove bottom hinge cover and mounting screws
• Transfer hinge pin and any spacers from the old bracket if applicable; install the new bracket and tighten screws securely
• Rehang and align the door; confirm full gasket contact and smooth door swing

A replacement center hinge pin that secures the refrigerator door at the center hinge assembly to restore proper pivoting and alignment. Use this pin to correct door sag or uneven closing caused by a worn or bent hinge pin. What it does

• Secures the door to the center hinge so the door can pivot smoothly.
• Restores proper door alignment and helps the door seat evenly against the cabinet.
• Commonly used to address door sag, rubbing, uneven gaps, or difficulty closing.
• Works as a direct replacement for the center hinge pivot in the hinge assembly.

• Always disconnect power to the appliance before servicing to avoid electrical hazards.
• Support the door and follow the appliance manufacturer's hinge removal steps before removing or installing the pin.
• Inspect surrounding hinge components (bushings, brackets) for wear while replacing the pin; replace as needed.

A non-metal shim used to stabilize and level your appliance for quieter, more reliable operation. Simple, low-profile support that helps correct minor height and balance issues so doors and drawers align and appliances sit securely. What it does:

• Adds thin, non-metallic spacing under feet or frame to correct slight height differences
• Helps stop rocking or tipping that can cause noise, vibration, or misaligned doors
• Supports even weight distribution to reduce uneven wear on adjustable legs
• Useful when adjusting leveling feet can't fully correct a gap or tilt

• Place shim under the appliance foot or frame where additional height or support is needed
• Re-check appliance level and stability after installing; add/remove shims as required
• Use with care to avoid creating instability; pair with proper leveling adjustments

This door hinge restores smooth, controlled door movement and a tight, secure close. Replace a bent or worn hinge to correct doors that sag, bind, or won't stay closed, helping your appliance seal properly and perform as designed.

• Supports and guides the door through its full range of motion
• Helps keep the door aligned so the gasket compresses evenly for a proper seal
• Controls closing action and stop position to protect the door and frame
• Common symptoms: door won't close flush, sags, pops open, or moves roughly/squeaks

• Disconnect power at the breaker and allow the appliance to cool completely before servicing
• Support the door; follow the service manual for door removal. Engage hinge locks or use retaining pins if equipped
• Transfer any screws/brackets from the old hinge to the new and install on the correct side if the design is side-specific
• Ensure the latch engages and the gasket seals uniformly all around

A small replacement closure shim that helps align and secure a closure/trim piece on select appliances, restoring proper fit and reducing rattles, rubbing, or gaps for quieter, more reliable operation. What it does:

• Positions and supports the closure/trim so panels and doors close evenly.
• Helps stop rubbing, misalignment, or minor gaps that can cause noise or poor sealing.
• Serves as a non-electrical spacer/aligner where the original shim has worn or broken.
• Useful when cosmetic trimming or closure pieces feel loose or shift during use.

• Disconnect power to the appliance before starting any repair or accessing panels.
• Access location may require removing the related trim, panel, or door—refer to the appliance diagram or service manual.
• Handle small plastic parts carefully; align the shim before fastening to avoid breakage.