Estate Dishwasher Parts

This pump outlet seal sits on the discharge side of the dishwasher pump to keep the outlet connection watertight. Replacing a worn seal helps stop leaks and keeps wash water contained during the cycle. What it does:

• Seals the joint at the pump outlet to prevent water leakage
• Helps maintain proper circulation by keeping the pump discharge airtight/watertight
• Common symptoms of failure include water under the unit, drips near the pump area, or a flattened/cracked/hardened old seal

• 1 pump outlet seal

• Disconnect power and shut off the water supply before servicing
• Remove the toe-kick/lower access panel to reach the pump area; place a towel or pan to catch residual water
• Note seal orientation; clean mating surfaces before installing the new seal
• Seat the seal evenly; reassemble and run a short test to check for leaks

The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.

Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.

Symptoms of a bad power cord include:

• The dishwasher not turning on or completing cycles
• Warm or hot power cords during operation
• Frayed, cracked, or exposed copper wiring

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

This base heater assembly restores the oven's lower heating function in select convection microwaves. It delivers bottom radiant heat for baking and crisping so the unit can preheat properly and brown foods evenly.

• Supplies bottom heat during convection, bake, or crisp cycles
• Works with the control and temperature sensor to reach and maintain set temperature
• Common symptoms of a failed heater may include no heat in convection mode, very long preheat, or poor browning/crisping
• Visible damage to the element or tripping a circuit breaker may also indicate a shorted heater

• Disconnect power before servicing. Microwaves contain high-voltage components that can retain a charge even when unplugged
• Allow the unit to cool completely; access typically requires removing the outer cover or lowering an over-the-range unit
• Note wire locations and routing before removal; transfer any brackets, shields, or screws from the original assembly
• Route wires exactly as original and avoid pinching; confirm clearances before reassembly and test a convection preheat

Left hand hinge. For right hinge use WP8066056

This lower spray arm assembly circulates wash water from the pump to clean dishes on the lower rack. The integrated shield helps direct water flow and protect the arm from debris, restoring consistent wash coverage.

• Distributes high-pressure water across the lower rack for effective cleaning
• Shield design helps prevent debris intrusion and improves spray pattern
• Common failure signs: poor lower-rack cleaning, noisy or restricted rotation, cracked or warped arm, clogged spray holes
• Also addresses leaking or splashing caused by a damaged or misaligned arm/shield

• Disconnect power and turn off water supply before servicing
• Remove lower rack; lift off old arm assembly per model design
• Clear any debris from pump outlet and sump before installing
• Ensure the new arm spins freely and is fully seated; test for smooth rotation

Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.

Supplies water to the spray arm.

Goes from pump to exterior drain hose.

Overfill control.

This rack adjuster assembly restores secure support and adjustable height for the dishwasher's upper rack. Replacing a worn or broken adjuster helps keep the rack level and sliding smoothly for easier loading and consistent wash performance. What it does:

• Supports and locks the upper rack at the selected height
• Allows smooth in-and-out movement when intact
• Helps prevent the upper rack from dropping, tilting, or feeling loose
• Common failure signs: rack won't raise/lower, falls off track, binds or feels rough

• One rack adjuster assembly

• Disconnect power to the dishwasher; shut off water supply
• Pull out the upper rack and remove end caps/stops before lifting the rack off the rails
• Release the old adjuster's locking tabs and install the new assembly in the same orientation
• Reinstall rack stops and test rack height adjustment and movement before restoring power

This replacement door spring maintains proper tension so the door opens smoothly and doesn't drop. Replace a weakened or broken spring to restore controlled, balanced door movement and everyday usability. What it does:

• Provides tension to balance the door's weight during opening and closing
• Helps prevent the door from slamming open or falling unexpectedly
• Common fix for a door that feels heavy, drops open quickly, or won't hold a mid-position
• Replaces springs that are stretched, fatigued, or broken

• 1 door spring

• Disconnect power before servicing; springs are under tension—use gloves and eye protection
• Note the spring's routing and hook positions; take a photo before removal
• Use pliers to release and attach the spring carefully to avoid sudden release
• Some models use two springs; replace both for even tension if applicable

Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679

This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.

• Connects water tubing between components within the appliance's water system
• Helps maintain a tight, leak-resistant seal at the joint
• Restores proper water flow when a tube or connector is damaged
• Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel or pan to catch any residual water
• Note routing and orientation before removal to ensure correct reassembly
• After installation, restore water and check all connections for leaks

Seal included. This sump housing assembly includes a 32.17 millimeter hole for the thermistor. If the hole for the thermistor is 31-31.5 millimeters you will need to order WP8534882.

This thermal fuse protects your appliance by opening the circuit if temperatures climb beyond a safe limit, helping prevent wiring or control damage. When it blows, the unit may lose all power or stop mid-cycle. What it does:

• Cuts power when overheating is detected to protect internal components
• Helps prevent damage from shorted heaters, motors, or wiring faults
• Common symptoms: no power, won't start, shuts off during operation, no lights/display
• A blown fuse reads open (no continuity) and must be replaced—it is not resettable

• 1 thermal fuse

• Disconnect power before servicing to avoid electrical shock
• Access the fuse location per your model's service information; note wire orientation and mounting
• Replace one-for-one; do not bypass or up-rate the fuse. Identify and correct the overheating cause before restoring power.

Color: White. Includes 125 caps used to cover damaged tips on your dishracks. For blue order 12022. For grey order 676458. To attach these tine tips you will need to order the dishrack white touch-up paint WP676453.