Estate Washer Parts

I purchased part #85753076A, Whirlpool Fabric Softener Dispenser. Popped off the top from the agitator and popped on the fabric softener dispenser. It took me less than a minute and it works perfectly! No more missing the rinse cycle!!! Read more

I could not find specific online instructions for this job. Here are some tips. 1. Unplug the washer. 2. Unscrew the dial on the broken timer. 3. Gently pry up the thin plastic place-indicator plate (the thing with the arrow under the dial) with two flathead screwdrivers. 4. Unscrew the two hex screws holding the old timer in place. 5. Unscrew the phillips-head screws holding the console in place and flip up the console. 6. Remove the electrical connector from the bad timer, and remove the bad... Read more

I diagnosed the problem, identified faulty parts, and replaced those components. Read more

• Will not agitate
• Will not drain
• Won't start
• Timer will not advance

Ordered new lid switch and plunger. Watched help videos and installed new parts, Washer works like new. Read more

The repair guy was going to charge me upwards of $225 to replace the timer in my washer, if in fact it was the timer. I decided with Christmas just a month away that there had to be a better way. After speaking with one repairman, and then searching on the internet, I found out the problem with my Kenmore washer was probably the timer. Sears was going to charge me a lot to ship the timer and they wouldn't allow me to return it if after replacing it, it wasn't the problem. So, I got back on... Read more

• Will not fill with water

I replaced it and the new one fit perfectly. reassembled and fired it up. Worked as desired, like new... Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

Replaced clutch assembly, gearcase input shaft seal and motor coupler. When I disassembled the washer I realized the shaft seal on the top of the gearcase was leaking and not the input shaft seal. So had to order more parts before I could finish this job. Altogether I replaced agitator dogs, both seals on the gearcase, the clutch assembly and the motor coupler. Agitator dogs replacement is a very easy job, no tools required, takes less that 5 minutes and made a huge difference with how well... Read more

Replace front legs and rear legs took about 30 minutes. Made sure rear legs had lithium grease applied ran a load of wash very little Vibration nothing compared to before legs were installed and balanced the machine with a level. Read more

I searched for parts on the internet regarding the make and model of my washer. Appliance Parts Pros not only had the part on a very user friendly website, but also had a well done video that made fixing the problem a breeze. Much appreciated and will buy from here from now on. Highly recommend! My local parts store did not have the part and would have to order it anyway. Read more

Separated oven door by removing screws. Inserted handle and secured with clips, and reassembledo door with screws provided. In served broiler handle and snappedal into place. Read more

I ordered the male and female door latching parts. Read more

• No heat or not enough heat

I ordered the parts through AppliancePartsPros.com. They were delivered the next day. I installed them and the dryer works great. Read more

• Will not stop filling with water
• Will not fill with water

Reviewed troubleshooting tips and identified problem as "water level switch". Watched repair video, which was very helpful. Ordered part on a Sunday, which arrived the following Tuesday. Repair was easy the fix was successful. Read more

Replaced ignitor with a new one. Should have tested old one before installing. New one did not work either. Traced problem back to defective thermo fuse by testing with a multimeter and found circuit open. Bought a new fuse and replaced. Ignitor cycling as designed now. Apparently fuse failed due to excessive heat. I will also replaced dryer vent hose and and clean out vent line. Read more

I replaced the cycle switch, fixing the lack of heat. The timer switch replacement fixed the auto cool down. I watched a cycle switch replacement on Youtube, demonstrating removal of the top console, which answered the only question I had about the repair. The timer switch was a hundred bucks. The only thing to be said about that is that it was a lot cheaper than a repairman or replacing the dryer. Read more