Frigidaire Range Burner & Related Parts

This medium crown burner sits on the gas cooktop/range burner to shape and distribute the flame for even heating. Replacing a worn or damaged crown restores reliable ignition and a consistent flame pattern on the medium-output burner.

• Distributes gas evenly around the burner for steady, uniform heat
• Works with the igniter for reliable lighting when properly seated
• Helps protect burner ports from spills and debris
• Helps with uneven or yellow flames, delayed ignition, inconsistent lighting, or visible cracks/warping

• Disconnect power and shut off gas; allow the surface to cool completely
• Remove the old crown and clean the mating surfaces
• Align the new crown with any locator pins/notches and seat it flat; if screws are present on your model, tighten gently and evenly
• Restore gas/power and test for proper ignition and flame pattern

The Cap-Burner is an OEM replacement part for Frigidaire cooktops. It is a component located at the top of each burner element on the cooktop. The cap-burner sits directly over the burner element to distribute and maintain heat levels evenly across the heating surface. 

Causes of a bad cap-burner can include warping or distortion from excessive heat exposure over time. Wet or sticky messes can also lead to clogging or blockages.

Symptoms of a bad cap-burner include: 

• Uneven or inefficient heating of pots and pans placed on the burner surface
• Hot spots or areas of excessively high heat 
• Burner elements that do not ignite or power on as expected
• Smoke or burning smells coming from below the cap-burner

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

The Surface Burner Cap is an OEM part for Frigidaire ranges. It fits over the surface burner, providing a protective cover while ensuring proper gas flow and flame distribution.

A bad surface burner cap can be caused by wear and tear, damage, or improper cleaning. When the burner cap becomes faulty, it can result in issues such as uneven flames, inefficient heating, or difficulty in maintaining a consistent temperature.

Symptoms of a bad surface burner cap include:

• Uneven or flickering flames
• Difficulty in reaching desired temperatures
• Excessive gas odor during burner operation

Replace your faulty surface burner cap with this genuine OEM Frigidaire part to restore your cooktop. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This sealed gas burner provides the primary cooking flame for compatible ranges, restoring even, reliable heat for stovetop cooking. Replace a worn or damaged burner to regain proper ignition and consistent simmer-to-boil performance. What it does

• Produces a controlled 14K BTU cooking flame for standard burner heating (per OEM listing)
• Replaces cracked, warped, or corroded burner surfaces that cause uneven cooking
• Helps address ignition failures, weak or irregular flames, and gas flow inconsistencies
• Fits into the burner bowl and works with factory burner caps and grates to seal heat and prevent spills

• One sealed burner (14K) as shown

• Turn off and disconnect the appliance from gas and electricity before servicing
• Handle carefully to avoid bending the burner tube or damaging the mounting tabs
• Use basic hand tools; confirm correct orifice and alignment when reinstalling

This black burner skirt fits around a 5K simmer burner ring to restore proper appearance and support the cooktop surface. Replaces cracked or damaged skirts to keep the burner area sealed and looking finished. What it does:

• Provides the decorative and protective trim around a 5K (5000 BTU) simmer burner
• Helps keep spills and debris from entering the burner cavity
• Restores even contact and alignment for the burner assembly
• Commonly replaced when the skirt is cracked, warped, or missing

• One black burner skirt (5K)

• Turn off and disconnect power and gas supply and allow all surfaces to cool before servicing
• Remove burner caps and grates per your model's service instructions to access the skirt
• Handle carefully to avoid bending or cracking; hand tools usually sufficient

This burner cap fits over a gas range surface burner to help direct the flame for even cooking and protect the burner head from spills and debris. Replacing a damaged cap restores proper flame shape and improves cooktop performance. What it does:

• Centers and shapes the gas flame for consistent heating across cookware.
• Protects the burner head from food, grease, and moisture that can impair ignition.
• Can resolve uneven or distorted flame appearance and reduce burner noise caused by damaged caps.
• Works with the corresponding burner base and cap seating system for safe burner operation.

• Turn off the range and ensure all components are cool before handling.
• Remove the old cap, clean the burner head of debris, then set the replacement cap into proper position—no tools usually required.
• Follow the appliance manufacturer's service instructions and safety warnings when servicing gas components.

A small replacement cap used to protect and secure a connection or component on compatible Frigidaire appliances. Restores a finished fit and helps prevent dirt, moisture, or accidental dislodging of the covered part. What it does:

• Covers and protects an exposed connection or assembly point
• Helps keep debris and moisture out of the covered area
• Secures the underlying component to reduce movement or accidental release
• Restores the appliance's original appearance at the capped location

• Disconnect power to the appliance before replacing any parts; shut off water supply if working near water lines
• Remove the old cap by gently prying or pulling straight off; avoid twisting to prevent damage
• Press the replacement cap firmly into place until fully seated and flush with surrounding surfaces