Frigidaire Wall Oven Parts

The Surface Element is an OEM part for Frigidaire electric ranges. As the key heating component on the cooktop, the surface element produces heat through resistance when electrical current flows through it.

Causes can be normal wear over time exposed to heat cycles, damaged or degraded internal components, corrosion of terminals or wires, or surface damage from improper cleaning.

Symptoms of a bad surface element include:

• Slow or uneven heating
• Burning or scorching of cookware easily
• Element that will not heat at all or only reaches low temperatures
• Frayed, cracked, or broken wiring at the element terminal

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Main Control Board is an OEM part for Frigidaire ranges. As the central processing unit, it coordinates bake/broil elements, lights, timers and sensory systems. Located inside the control panel area, this board continuously monitors range functions and relays information to the control display.

Causes can be splash or spill damage, power fluctuations over time, or inherent component failures due to age and usage. With proper replacement, full range functionality is restored.

Symptoms of a bad control board include:

• Knobs or buttons not working on the control panel
• Elements failing to heat properly
• Erratic temperature display readings
• Inability to preheat or maintain set oven temperatures
• Control locks that prevent range operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This spark module powers the surface-burner ignition on gas ranges and cooktops. It generates high-voltage pulses to the electrodes so the burners spark and light when a knob is turned, restoring quick, consistent ignition.

• Sends high-voltage pulses to each surface burner igniter when a burner switch is turned on
• Centralizes spark for multiple burners; a failure often affects more than one burner
• Common symptoms: no clicking/spark on any burners, multiple burners won't light, weak or intermittent spark, continuous clicking from the ignition system
• Helps restore reliable lighting without using matches

• Disconnect electrical power and shut off gas before servicing
• Note wire locations; transfer leads one at a time to matching terminals on the new module
• Mount securely in the original position and ensure proper grounding
• After installation, verify spark at each burner before restoring full operation

This replacement thermostat is a temperature-sensitive switch used in select cooking appliances. It opens or closes at a fixed setpoint to control or limit heat, helping protect components and restore dependable operation of the affected circuit. What it does:

• Senses temperature at its mounting point and opens/closes electrical contacts at a designed setpoint
• Controls power to a heating or related circuit (such as an element or fan) to maintain safe operation
• Helps prevent overheating and protects internal components
• Failure can cause no heat, heat that shuts off prematurely, or a related circuit that won't turn on/off

• 1 thermostat

• Disconnect power to the appliance before servicing
• Access location varies by model; refer to your service manual for exact placement
• Move wires one at a time from the old part to the new to maintain correct connections
• Reinstall in the same orientation; ensure firm mounting for proper temperature sensing and secure electrical connections

The Door Handle Kit is an OEM replacement part for Frigidaire ovens and ranges. These handles provide safe access to the oven interior.

Causes of a bad handle kit can include normal wear over time of moving parts, accidental damage from impact or mishandling of the oven door, or issues with the latching mechanism.

Symptoms of a bad oven door handle kit include:

• Loose, sluggish, or difficult operation of handles
• Handles detaching from oven door
• Inability to fully open or close the oven door
• Problems with door sealing or staying closed securely

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Restore reliable lighting. This ignitor wire harness carries power from the ignition control to the ignitor, replacing cracked or shorted wires that cause weak/no spark or glow so your burner or oven can ignite consistently.

• Provides the dedicated electrical path between the ignition control and the ignitor
• Replaces heat-brittled, cut, or shorted leads to maintain proper insulation
• Helps address: burner or oven won't ignite, intermittent ignition, ignitor won't spark or glow
• Visual clues can include scorched insulation or corroded connectors

• Disconnect power and shut off gas; allow the appliance to cool completely before servicing
• Note original routing and connections; move one connector at a time to avoid cross-wiring
• Route wires away from sharp edges and hot surfaces; secure with original clips/ties
• Ensure all connections are fully seated, then restore power/gas and test ignition

This surface burner mounts on the cooktop and directs gas to produce a steady, controllable flame. Replace a worn or clogged burner to restore fast ignition and consistent heat from your range's top burner positions.

• Mixes and distributes gas to create the surface cooking flame
• Works with the spark igniter/electrode for reliable lighting
• Helps maintain an even flame pattern and stable heat
• Symptoms can include weak or uneven flames, yellow tips, delayed ignition/repeated clicking, or a burner that won't light

• Disconnect power and shut off the gas supply before servicing
• Remove the grate and burner cap, then lift off the old burner; clean the mounting surface
• Align the new burner with the igniter/electrode and locator features; ensure it sits flat and centered
• Reassemble, restore gas/power, and test for proper ignition and a clean, stable flame

The Frigidaire Range Control is an OEM component specifically designed for Frigidaire ranges. Located on the control panel, the range control houses all interactive buttons and knobs to operate the cooktop burners and oven. 

Causes of failure include damage from excess moisture, cracks developing from repeated tightening/loosening of knobs, or wear of electronic switches impacting responses.

Symptoms of a bad range control include:

• Unresponsive or inaccurate oven/stovetop controls  
• Inability to power on or adjust temperatures
• Faulty burners failing to ignite or flame improperly
• Loose, damaged, or missing knobs hindering the use

This OEM component is also compatible with Crosley, RV, and some Kenmore-branded ranges and ensures a straightforward repair experience.

This is a surface burner head for a gas range/cooktop. It distributes gas from the orifice to the burner ports, helping deliver an even flame and reliable ignition when the original head is clogged, damaged, or corroded.

• Channels gas through precision ports to create a stable, even cooking flame
• Works with the burner cap and igniter for quick, consistent lighting
• Typical symptoms: burner won't light or takes multiple clicks, uneven/yellow flames, weak flame, or popping/flare-ups
• Physical issues may include blocked ports, heavy corrosion, or a warped/stripped casting

• Disconnect power and shut off gas; let the cooktop cool completely
• Lift off the burner cap; remove mounting screw(s) if present and lift off the old head
• Clean mating surfaces/orifice area; set the new head squarely and secure with existing hardware
• Restore gas and power; verify proper ignition and flame pattern

This replacement control knob restores reliable, precise control of your range. It presses onto the control shaft so you can select heat or temperature settings and replaces cracked, stripped, or missing knobs for everyday, dependable use.

• Attaches to the control stem to turn the switch or valve
• Lets you set burner levels or oven temperature, depending on the control
• Common failure signs: cracked knob, stripped insert, loose fit, missing knob, or difficulty turning the control
• Helps ensure the control can be turned fully to Off and desired settings

• Disconnect electrical power; for gas ranges, also shut off gas supply if working near valves
• Pull the old knob straight off the control stem; do not pry against the panel
• Align the new knob with the stem orientation and press straight on until fully seated
• Verify smooth operation and proper alignment with Off before use; do not force

This replacement switch restores reliable on/off signaling for a specific circuit in your appliance, helping the intended function operate consistently and safely. It's a direct-fit part used in select cooking appliances where a mechanical/electrical switch is required. What it does:

• Opens and closes an electrical circuit when actuated to control a designated function (such as a light, interlock, or enable signal), per model design
• Helps the control system detect a condition (e.g., a door position) to allow or inhibit operation
• Resolves issues like a light that won't turn on/off, "door open" messages when closed, or functions that start/stop unexpectedly
• Replaces a worn, stuck, or intermittently failing switch that causes inconsistent operation

• One switch

• Disconnect power before servicing; this part carries live voltage during operation
• Access the switch at its mounting location
• Move wires one at a time from the old switch to the new to maintain correct terminal positions; ensure snug, clean connections
• Test function before reassembly to confirm proper actuation and operation

The Broil Element is an OEM replacement part for  Frigidaire electric ranges. It is an electric heating component located at the top of the oven used for broiling food. The broil element generates intense radiant heat from above, allowing food to brown and crisp up while also cooking from direct heat exposure. It is crucial for the broil cooking function. 

Symptoms of a bad broil element include:

• The broil feature failing to get the oven hot enough or working inconsistently
• Discoloration, rusting, or other signs of deterioration on the element  
• Tripping of the circuit breaker or thermostat when using broil
• Food not browning or crisping up as expected under the broiler

Causes can be standard wear and tear over many heating and cooling cycles or damage from cleaning products or spatters inside the oven.

This OEM Frigidaire replacement part is also compatible with some Electrolux, Westinghouse, and Kenmore electric ranges.

This terminal block kit restores a secure, heat-resistant connection point for your appliance's incoming power. Replacing a damaged block helps prevent intermittent power loss and further heat damage from loose or burnt terminals.

• Provides an insulated junction for incoming power leads
• Restores a tight, reliable connection between supply wires and internal wiring
• Helps resolve no power, intermittent power, or visible heat damage at the terminal area
• Replaces cracked, melted, or burned blocks to protect wiring and performance

• Disconnect power at the breaker and verify no voltage is present before servicing
• Label/photograph existing wiring; move one conductor at a time to the new block and tighten terminals securely
• Inspect the cord and wire ends; replace any burnt, brittle, or damaged conductors or lugs before reassembly
• Reinstall covers/strain relief as applicable and verify connections are secure before restoring power

The Rocker Switch is an OEM part for Frigidaire ranges and ovens. It is responsible for turning the interior oven light on and off. The light switch allows visibility of the oven cavity for viewing food during the cooking process.

Causes can include normal wear and tear over time, exposure to heat inside the oven cavity, or accidental damage.

Symptoms of a bad oven light rocker switch include:

• The oven light failing to illuminate when the door is opened
• The light remaining on even when the door is closed
• An inconsistent or flickering oven light
• The switch itself becoming loose, cracked, or non-responsive

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Color: White.

This oven bake element supplies the lower-oven heat for Bake cycles. Replacing a failed element restores proper preheating and consistent temperatures so your electric range or wall oven bakes reliably again. What it does:

• Provides radiant heat from the bottom of the oven during Bake
• Helps the oven reach and maintain the set temperature
• Failure symptoms can include: no heat in Bake, very slow preheating, uneven baking, or the element not glowing
• Visible damage such as breaks, blisters, or burned spots indicates replacement is needed

• One bake element

• Disconnect power at the breaker before servicing
• Remove oven racks; unfasten the element's mounting screws, then gently pull the element forward and transfer the wires one at a time
• Reuse existing mounting hardware; ensure terminals are fully seated and not contacting the oven cavity
• Restore power and test Bake; the element should heat evenly