General Electric Dishwasher Parts

NOTE: The clamps no longer come with the connector hose. The part number for the clamp is WD01X10322.

Dishwasher won't start, stops mid-cycle, or won't dry? The control module manages timing and powers all cycles. Moderate DIY repair restores function.

Replacement touch pad that restores your dishwasher's control interface. Needed when buttons are unresponsive, worn, hard to read, or the overlay is cracked.

Includes 12 screws.

This hex washer-head screw is used in dishwashers to secure panels, brackets, and other hardware. Replacing a missing or corroded fastener restores a tight, stable installation and helps stop looseness or vibration during cycles.

• Fastens dishwasher panels, brackets, trim, or mounts to the cabinet/frame
• Replaces lost or stripped hardware after service or installation
• Helps address loose or rattling panels and minor misalignment
• Stainless steel construction per OEM spec for moisture-prone environments

• Disconnect power and water supply before servicing the dishwasher
• Wear gloves; sheet metal edges can be sharp
• Start threads by hand to avoid cross-threading; tighten with an appropriate driver
• Do not overtighten, especially when threading into plastic

Lower rack roller and stud assembly for dishwashers. Mounts to the bottom rack to allow smooth sliding in and out. Replace if broken, cracked, or missing.

Cap assembly for dishwasher door. Installs on the interior door panel to seal openings. Replace if cap is missing, cracked, or broken during shipping.

Covers the electrical junction box where the power cord enters your dishwasher. Replace if cracked, broken, or missing to protect wiring connections.

A replacement clamp that secures hoses or wiring to keep lines routed and stable, helping prevent rubbing, leaks and noise. Restores a reliable hold for tubing and harnesses so the appliance runs quietly and safely. What it does:

• Holds hoses, tubing or wire harnesses in place to reduce movement and chafing.
• Helps prevent leaks and water line abrasion caused by loose fittings.
• Reduces rattling or vibration from unsecured lines or cables.
• Keeps routing organized so adjacent components aren't stressed or worn.

• Disconnect power before servicing the appliance; shut off water supply when working on water or drain lines.
• Remove the old clamp and position the replacement so it fully engages the hose or harness, avoiding twists.
• Use appropriate hand tools (pliers or screwdriver) and secure the clamp evenly; avoid overtightening.
• Inspect surrounding hoses and wiring for damage while installing; replace any components that show wear.

A replacement electronic control module that manages the appliance's cycle functions and user commands, restoring reliable control and timing when the original module fails. Replaces a faulty control assembly to help return normal operation. What it does:

• Controls cycle timing, power distribution, and signals between sensors and the user interface.
• Replaces a failing control when the appliance won't start, is unresponsive to button presses, or stops mid-cycle.
• Works as the central command board that interprets inputs and runs programmed cycles.

• 1 Module control assembly

• Disconnect power (and water supply for washers) before attempting any repair.
• Handle the board by its edges and avoid touching components; use anti-static precautions if available.
• Reconnect all wiring harnesses and secure mounting hardware before restoring power.

Fix dishwasher cycles not running or dishes not drying. This control board manages cycle selection, timers, and heating element operation.

Color: White.

Secures dishwasher hoses to fittings and prevents leaks. Replace if corroded, rusted, or loose to restore a watertight seal. Confirm fit with your model.

This hex-head screw secures dishwasher panels, brackets, and internal hardware so parts stay tight and rattle-free. Replace missing or stripped fasteners to restore a secure fit and reliable operation.

• Fastens panels, brackets, and other dishwasher components to the tub or frame
• Replaces a missing, stripped, or corroded screw that no longer holds securely
• Helps eliminate vibration and rattling caused by loose hardware
• Maintains proper alignment and secure mounting of parts during operation

• Disconnect power and shut off water supply before servicing
• Keep track of fastener locations and orientation for correct reassembly
• Start threads by hand; use an appropriate nut driver or socket to tighten
• Tighten snugly—do not overtighten, especially when threading into plastic

The dishwasher guide rail back cap secures and protects the end of the dish rack sliding mechanism. Replace when the cap breaks or comes loose, causing the rack to slide improperly or fall off its track.

Secures the dishwasher sump connection at the tub base for a leak-resistant seal. Replace if weakened or corroded to stop drips. Confirm fit with model.