General Electric Dishwasher Pump

This is a replacement washer drive motor that powers the tub to spin and agitate, restoring normal wash and spin cycles. Fits specified GE top-load washers and matches OEM form and function. What it does

• Spins the wash tub to perform spin cycles and remove water
• Powers the agitation/oscillation action during wash cycles
• Commonly replaced when the washer won't spin, won't agitate, or hums without turning
• Helps eliminate intermittent power-to-motor issues when motor failure is the root cause

• One replacement drive motor

• Disconnect power before starting any repair to avoid electric shock
• May require removing the washer cabinet or access panels and detaching the old motor wiring and mounting screws
• Handle carefully — support the tub/drum as needed during motor removal and reinstallation

This is the mechanism S/S assembly used to control the appliance's mechanical functions and restore proper operation. Replacing a worn or broken mechanism helps resolve intermittent or failed mechanical actions and audible clicking. What it does:

• Transfers user input into mechanical movement to operate the appliance's internal components
• Engages and releases internal linkages for door, latch, or control actions
• Restores consistent mechanical response when original mechanism is worn, stuck, or broken
• Can stop symptoms like inconsistent operation, failure to engage, or unusual noises during cycles

• One mechanism S/S assembly

• Replace only with the exact OEM part number
• Disconnect power (and water, if applicable) before attempting any repair
• Handle small components carefully; keep screws and clips organized for reassembly

This dishwasher drain pump removes wastewater from the tub at the end of cycles, helping prevent standing water and ensuring proper draining performance. Replacing a failing pump restores efficient water removal and helps avoid wet dishes and odors.

• Pumps water out of the dishwasher to the household drain
• Common symptoms: won't drain or leaves water in the bottom, unusual humming/buzzing during drain, intermittent or slow draining
• Also helps if the pump is seized or electrically failed

• Disconnect power and turn off water before servicing
• Protect the floor from residual water; have towels or a shallow pan ready
• Access is typically from the bottom/front; transfer wiring and hose clamps to the new pump
• Ensure a clear, unkinked drain hose and a clear air gap or disposal inlet after installation

This sump cap seals the sump opening at the bottom of the dishwasher tub to contain wash water and protect the pump. Replace a cracked, loose, or missing cap to help prevent leaks and maintain proper wash performance. What it does:

• Seals the sump opening to keep water inside the tub and direct flow to the pump
• Helps keep debris out of the pump intake
• Restores a secure fit when the original cap is cracked, stripped, or warped
• Common symptoms: water leaking from the base, moisture under the dishwasher, visible damage, or a missing cap

• Disconnect power and turn off the water supply.
• Remove the lower rack and, if needed, the lower spray arm to access the sump.
• Remove the old cap and clean the sealing area; install the new cap and hand-tighten until snug—do not overtighten.
• Run a short cycle and check for leaks around the sump.

This replacement pump drain pumps water from the washer tub so cycles can finish and clothes don't sit in standing water. Fits as the direct OEM-style drain pump to restore normal draining and rinse/spin performance. What it does:

• Pumps out wash and rinse water so cycles can complete without standing water
• Stops or reduces common drain-related issues like slow draining or water remaining after a cycle
• Resolves error codes or pump-noise symptoms caused by a failed or clogged pump
• Works with the washer's drain hose and tub to maintain proper water flow during spin

• Disconnect power and turn off water before beginning any repairs
• Inspect and clear drain hoses and filters while replacing the pump to prevent repeat clogs

A dishwasher sump assembly that houses the pump and routes wash water; replaces a damaged or leaking sump to restore proper draining and circulation. Designed to fit as the factory-style replacement for the original sump. What it does

• Channels and collects wash water for the dishwasher pump to circulate and drain.
• Replaces cracked or warped sump housings that can cause leaks under the appliance.
• Can stop intermittent draining problems or pump cavitation caused by a damaged housing.
• Helps reduce vibration and noise when the pump and housing are functioning correctly.

• One sump assembly.

• Disconnect power and water to the appliance before beginning any repair.
• Inspect surrounding seals, gaskets and fasteners during install; replace any damaged items.
• Tighten mounting hardware to OEM torque and ensure proper alignment to prevent leaks.
• Test or replace those components separately as needed.