General Electric Dryer Bracket & Flange

The Bearing Retainer is an OEM replacement part for GE electric dryers. It is an internal component that securely holds the drum bearing assembly in place to enable smooth rotation and provides structural bracing for the bearing during tumbling cycles.

Causes of a faulty retainer can include cracks from heat exposure over years of use. Impact damage from foreign objects inside the drum is also possible. 

Symptoms of a bad bearing retainer include:

• Excessive vibration or noise during drying cycles  
• Wobbling or misalignment of the rotating drum
• Premature failure of other moving parts due to lost structural support

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This ground strap assembly bonds the dryer's cabinet to the designated ground point, helping ensure safe operation. Replace a damaged or missing strap to restore a proper ground path and reduce the risk of shocks or nuisance static.

• Maintains the required electrical bond between the dryer chassis and ground as designed
• Helps prevent electric shock and reduces static by providing a low-resistance path to ground
• Replace if the original strap is loose, corroded, heat-discolored, broken, or missing
• Symptoms can include a slight tingle when touching the appliance or visible damage near the ground/terminal connection

• Disconnect power at the breaker before servicing; verify no power with a meter
• Follow your model's wiring diagram; bonding differs for 3-wire vs 4-wire cord installations per local codes
• Clean contact surfaces and secure fasteners firmly for a solid metal-to-metal bond; replace any heat-damaged hardware
• After installation, verify continuity between the cabinet and the designated ground point

This dryer bearing bracket secures the drum's rear bearing to keep the drum aligned and rotating smoothly. Replacing a worn bracket can help reduce drum wobble, scraping noises, and uneven drum rotation. What it does:

• Supports and locates the rear drum bearing to maintain proper drum alignment.
• Helps prevent the drum from wobbling, rubbing, or scraping against the cabinet.
• Can reduce or eliminate grinding, squealing, or thumping noises caused by a loose or damaged rear support.
• Works with the dryer's rear bearing assembly to enable consistent drum rotation.

• Disconnect electrical power (and gas, if applicable) before beginning any repair.
• Access typically requires removing the dryer drum and rear bulkhead.
• Inspect the bearing, shaft, and surrounding glides; replace any worn components to prevent repeat failure.

This rear level leg bracket replaces the rear mounting bracket that secures a leveling leg to the appliance frame, restoring proper support and helping keep the appliance stable and level for safe, quiet operation. What it does:

• Secures the rear leveling leg to the appliance frame so the cabinet sits evenly
• Restores proper height and prevents the appliance from tilting backward
• Reduces rocking, wobbling, and vibration caused by a damaged or loose bracket
• Helps maintain safe, stable operation under normal load conditions

• Disconnect power (and gas supply if applicable) and move the appliance to a safe, accessible area before starting.
• Support the appliance cabinet so it cannot tip when the rear leg or bracket is removed.
• Use basic hand tools to remove and install the bracket; follow the appliance manufacturer's instructions.
• Inspect the leveling leg and front mounts while servicing; replace any worn or damaged hardware.

This bracket belt switch assembly secures the dryer belt switch and helps stop the motor if the belt slips or breaks, protecting the dryer from damage and preventing unsafe operation. It's a direct-fit replacement for the original mounting assembly. What it does

• Holds the belt switch in the correct position so it can sense belt tension.
• Opens the circuit when the belt is loose or broken to stop motor operation.
• Can resolve symptoms like a dryer that stops mid-cycle, fails to start, or runs but won't tumble.
• Restores the original mounting and switch alignment for reliable belt sensing.

• One bracket belt switch assembly

• Disconnect power before beginning—this part is used on electric and gas dryers.
• Basic hand tools (screwdriver/socket) are typically required; keep track of mounting hardware.
• Inspect the belt and pulleys while replacing the bracket; replace any worn parts.

This levelling leg support bracket secures and stabilizes an appliance leg to keep the appliance level and steady on uneven floors. Restores proper footing to reduce rocking and improve door and drawer alignment. What it does:

• Holds the adjustable levelling leg in place so the appliance sits level and stable
• Helps stop rocking, tipping, and uneven operation caused by a loose or damaged bracket
• Restores proper appliance alignment to improve door and drawer sealing and operation
• Works with the factory levelling leg assembly to transfer weight to the cabinet/frame

• Designed for use with the factory levelling leg assembly;
• Turn off and unplug the appliance and empty any contents before working underneath
• Use basic hand tools; avoid forcing parts to prevent damage to cabinet or fasteners
• If mounting fasteners are damaged or missing, replace them with OEM-equivalent hardware

This bracket gasket felt is a thin felt cushioning strip that mounts to a bracket or cabinet to reduce metal-on-metal contact and quiet vibration. It helps protect finishes and prevents rattles where parts meet. What it does

• Cushions contact between a bracket and cabinet or other metal parts to reduce noise and wear
• Helps prevent scratching and scuffing on mating surfaces
• Reduces vibration-driven rattles around the bracket area
• Simple, passive part with no electrical function

• Disconnect power to the appliance before beginning any work when applicable.
• Remove the bracket or access panel to expose the mounting area; replace the old felt with the new strip in the same position.
• Press the felt into place; secure using the original fasteners or adhesive method used by the manufacturer.
• Wear gloves to protect hands from sharp edges.