General Electric Dryer Gasket & Seal

The Dryer Front Bearing Drum Slide (White, 2-Pack) is an OEM replacement part for GE dryers. These slides are located on the front panel of the dryer and work to support the drum as it rotates. The white slides are designed to reduce friction between the drum and the panel, ensuring smooth operation and helping to prolong the life of the appliance.

Over time, these slides can wear out due to constant movement, heat, and friction. When worn or damaged, the drum may not rotate as intended, leading to noise and reduced efficiency.

Symptoms of bad dryer front bearing drum slides include:

• Squeaking or grinding noises during operation
• The drum appearing loose or sagging at the front
• Clothes not drying evenly or taking longer to dry
• Visible wear or thinning on the existing drum slides

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Dryer Front Bearing Drum Slide (Green, 2-Pack) is an OEM replacement part for GE dryers. These slides are located on the front panel of the dryer and work to support the drum as it rotates. The green slides are designed to reduce friction between the drum and the panel, ensuring smooth operation and helping to prolong the life of the appliance.

Over time, these slides can wear out due to constant movement, heat, and friction. When worn or damaged, the drum may not rotate as intended, leading to noise and reduced efficiency.

Symptoms of bad dryer front bearing drum slides include:

• Squeaking or grinding noises during operation
• The drum appearing loose or sagging at the front
• Clothes not drying evenly or taking longer to dry
• Visible wear or thinning on the existing drum slides

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Lower Drum Felt seal is an OEM replacement part for GE dryers. The Lower drum felt seal is responsible for creating a seal between the drum and the front panel of the dryer.

This part fixes the following symptoms:

• Air leaking from the dryer drum
• Reduced dryer efficiency and increased energy costs
• Clothes becoming caught in the gap between the drum and front panel
• Potential damage or snags to clothes or the dryer

Causes of a bad Lower Drum Felt Seal can range from normal wear and tear, which degrades the felt material over time, to excessive load sizes that strain the drum and seal. Additionally, over time, the seal can become compressed or damaged, leading to a less effective seal and the potential for heat loss and inefficiency in the drying process.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Lint Screen Housing Seal is an OEM part for GE dryers. This seal is designed to fit around the housing of the lint screen, ensuring a tight seal that prevents lint and small particles from bypassing the filter and entering the dryer's internal components. This seal measures approximately 36” long.

Symptoms of a failing lint screen housing seal include:

• Increased accumulation of lint inside the dryer cabinet
• Decreased drying efficiency, requiring longer cycles to dry clothes
• Visible wear or gaps in the seal

Causes of wear or failure of the lint screen housing seal often include regular use, which can stretch or tear the material, exposure to high temperatures which can degrade the rubber or foam, and improper installation which can lead to a poor fit.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The O Ring is an OEM part for GE dryers, creating a tight seal in different components for efficient operation. This small part prevents air leaks that can impact drying performance, made from quality materials to withstand high temperatures and frequent use

Causes of a faulty O Ring in a dryer may stem from heat exposure, regular wear and tear, or chemical damage. This can result in reduced elasticity, cracks, or breaks, impacting the seal.

Symptoms of a bad O Ring in your dryer include:

• Reduced efficiency in drying, as air leaks can affect the dryer's ability to maintain the correct temperature.
• Unusual noises stemming from air escaping through the compromised seal.
• Potential for small leaks or condensation within the dryer's internal components, leading to moisture issues.

This genuine GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This cleaning felt mounts on the dryer's front shroud. It lightly contacts the rotating drum to wipe away lint and residue, helping keep the drum edge clean and supporting consistent airflow to the lint filter.

• Provides a soft wiper against the drum rim to reduce lint and residue buildup
• Helps maintain smooth drum rotation and a clean front duct area
• Wear signs include frayed or missing felt, lint trails on fabrics, or light squeaks at the front
• Visual inspection is recommended if lint accumulates inside the drum after cycles

• Disconnect power; for gas dryers, also shut off gas supply
• Access the front panel/shroud and note the original felt's orientation before removal
• Clean the mounting surface; install the new felt in the same position (some models use clips or adhesive)
• Hand-rotate the drum to ensure even, light contact before reassembly and testing

This felt seal creates a smooth, airtight barrier where the drum meets the bulkhead in your dryer. Replacing a worn seal helps maintain proper airflow, protect fabrics from snagging, and reduce scraping or squealing noises during operation. What it does:

• Seals the gap between the rotating drum and front/rear bulkhead to contain heat and airflow
• Provides a low-friction, cushioned surface for the drum rim
• Helps keep lint and debris out of the cabinet
• Common symptoms of failure: longer or uneven dry times, rubbing/scraping noises, clothes catching or leaving marks at the drum edge, visibly worn or torn felt

• 1 felt seal

• Disconnect power; for gas dryers, also shut off the gas supply
• Remove the top/front panel to access the drum and bulkhead; support drum as needed
• Remove old felt and adhesive; clean the mating surface thoroughly
• Dry-fit the new seal; install per manufacturer guidance; allow proper set time before reassembly
• Hand-rotate the drum to verify even contact and clearance, then test operation

The Gasket Seal is an OEM component specifically designed for GE dryers. It is a crucial sealing component that lines the perimeter of the dryer door. The gasket seal helps create an effective air barrier when the door is properly closed and secured.  

Causes of a bad gasket seal can include wear and tear resulting in cracks along the surface, deformities preventing flush contact with the door border, or material deterioration compromising its sealing abilities.

Symptoms of a bad gasket seal include:

• Excessively long drying cycles as air escapes around the compromised seal    
• Visible lint or debris collections where the gasket meets the door framing
• Noticeable drafts or air gaps discernible across the door perimeter

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Green bearing slide that replaces a worn bearing guide in select GE laundry appliances, helping restore smoother drum movement and reduce vibration and noise from a misaligned bearing assembly. Fits where the bearing rides or is guided. What it does:

• Guides the bearing assembly for steadier drum rotation — symptoms include grinding, squeaking, or rough spin cycles.
• Helps correct minor drum wobble and imbalance caused by a worn guide surface.
• Protects the bearing mating surface from accelerated wear by maintaining alignment.
• Can improve spin stability and reduce abnormal vibration when the guide is failing.

• Disconnect power and water supply before beginning any repair.
• Part typically accessed by removing the washer front panel or tub components.
• Verify the part number and color match your machine before installing.

This door gasket is the flexible rubber seal that mounts around the refrigerator door to maintain an airtight seal, helping preserve internal temperatures and reduce energy loss from leaks. What it does:

• Seals the gap between the refrigerator door and cabinet to keep cold air inside.
• Prevents moisture intrusion, reducing frost, condensation, and excessive compressor run time.
• Restores proper door contact when original gasket is cracked, torn, warped, or no longer seals.
• Common symptoms: visible gaps, light showing around closed door, frost buildup, or higher-than-normal interior temperatures.

• Disconnect power to the appliance before beginning any work.
• Remove the old gasket and clean the door channel; inspect the mounting surface for damage.
• Press the new gasket into the channel starting at the corners, working around the door for an even fit; warm the gasket slightly (hair dryer on low) if needed to help seat it.
• Avoid sharp tools that can tear the gasket.

This genuine-style door gasket replaces a worn or damaged refrigerator door seal to restore a tight closure and help maintain proper cooling. It stops cold air loss and reduces frost build-up when sealing correctly. What it does:

• Seals the refrigerator door to keep cold air in and warm air out
• Helps reduce frost and moisture buildup inside the compartment
• Can improve cooling consistency and reduce energy waste when effective
• Commonly replaced for visible cracks, tears, or a flattened seal that no longer closes snugly

• Disconnect power to the appliance before starting any service
• Clean the door frame and mating surface before installing the new gasket
• Align the gasket evenly around the door and press into the channel until fully seated
• Check door alignment and hinges to ensure a proper long-term seal

This felt gasket assembly cushions and seals the dryer drum edge to reduce rubbing, keep fabric from catching, and help direct airflow. It restores smoother drum rotation and reduces noise caused by worn or torn felt. What it does:

• Provides a soft seal between the drum and bulkhead to prevent garments from catching on the drum edge
• Dampens vibration and reduces scraping or squeaking noises from drum contact
• Helps maintain proper airflow path and keeps lint out of the gap near the drum
• Common signs you need it: visible wear or fraying, fabric snags at the drum opening, or increased noise during rotation

• Disconnect power (and gas if applicable) before starting any repair
• Remove the dryer front or drum to access the gasket location
• Inspect adjacent seals, drum rollers, and the bulkhead for wear while replacing the felt
• Use OEM replacement and follow torque/fastening points for reassembly

This exhaust blower gasket seals the joint between the dryer's blower outlet and exhaust duct. It helps maintain proper airflow and contain lint and heat, supporting efficient drying and preventing leaks into the cabinet or laundry area. What it does:

• Seals the blower-to-exhaust connection to prevent air and lint leaks
• Helps maintain designed airflow through the drum and vent system
• Can reduce warm air or lint escaping inside the cabinet

• 1 gasket

• Disconnect power; for gas dryers, shut off gas and disconnect the supply. Allow the dryer to cool.
• Access the blower housing/exhaust duct; remove panels as needed.
• Remove the old gasket and any residue; clean mating surfaces and lint before installing.
• Seat the new gasket evenly and reassemble; avoid overtightening fasteners and ensure the home vent is clear.