Skip to Content
  • time delivery images 2 Day Quick Delivery!
  • box-refresh images 365 Day Return Policy!
  • lovely images 15 million satisfied customers
  • boxes images Over 2.1 Million Parts In Stock
  • headphone imagesFree Tech Support!
  • google images Google Trusted Store

General Electric Dryer Touch Pad

Best Seller
Ge Back Panel Assembly
Genuine Ge part
By: Ge
Part Number: WE19M1490

This back panel assembly replaces a damaged or missing rear cabinet panel to protect internal components and keep the unit's cabinet aligned and secure. Restores a clean fit and helps reduce rattles from a loose or bent back. What it does:

  • Encloses and protects internal wiring and components at the rear of the unit
  • Provides mounting points for rear hardware and brackets
  • Helps maintain cabinet alignment and structural rigidity
  • Can reduce noise from vibration when the rear panel is properly secured
What's included:
  • One back panel assembly
Install notes:
  • Disconnect power before servicing; if applicable, shut off gas supply
  • Pull the unit forward to access the rear; wear cut-resistant gloves—edges can be sharp
  • Retain and transfer any clips, ground straps, or grommets from the old panel
  • Route wires carefully and tighten fasteners evenly so the panel sits flush

Do-It-Yourself Stories from Customers like You Stripped knobs which broke inside of control panel shorted start switch   Amy O. • Raleigh , NC • August 31, 2016

After unplugging the dryer, I removed knobs and control panel. I removed the 3 connectors to start switch. I had to cut and replace one connector due to shorted wire which burnt the connector. I attached new connector and then attached these to start switch. I then remounted all three switches to new control panel and reattached control panel to dryer. Plugged in and started right up! Thank you for the helpful video. Read more

More
$142.95
Compare At:
$170.11
You Save:
$27.16

IN STOCK
Ships Today Guaranteed
Add to Cart
Best Seller
Ge Back Panel Assembly
Genuine Ge part
By: Ge
Part Number: WE19M1493

The Back Panel Assembly is an OEM part for GE dryers. It provides structural support and protection for the internal components of the dryer, including the control board, wiring, and venting system. This panel is designed to fit securely at the rear of the dryer, maintaining the integrity and safety of the appliance.

Causes of a bad back panel assembly can include exposure to moisture, physical impacts, or general wear and tear over time. A compromised back panel can lead to issues with the dryer’s operation and may pose safety hazards.

Symptoms of a bad back panel assembly include:

  • Visible dents or holes in the panel
  • Rust or corrosion on the panel surface
  • Loose or misaligned panel causing vibrations or noise
  • Difficulty in securing the panel properly during maintenance

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Do-It-Yourself Stories from Customers like You Start switch fell in to back splash   Joe K. • Warren , MI • June 09, 2016

Replaced back splash on dryer, repair took 5 minutes Read more

More
$157.56
Compare At:
$185.92
You Save:
$28.36

IN STOCK
Ships Today Guaranteed
Add to Cart
Ge Backsplash Assembly With Graphics (White)
Genuine Ge part
By: Ge
Part Number: WE19M1678

This backsplash assembly with graphics replaces the rear control panel on compatible dryers. It restores a rigid mounting surface and clear cycle labeling for the timer and switches, improving appearance and helping the controls align and operate properly.

  • Mounts and aligns the timer and switch controls on the console
  • Provides printed cycle and option identifiers for accurate selection
  • Helps resolve cracks, dents, broken tabs, or missing/illegible markings on the original panel
  • Can reduce rattling or loose-feeling knobs when the old panel is damaged
What's included: One backsplash panel with factory-applied graphics in white. Install notes:
  • Disconnect power; turn off gas supply for gas models.
  • Remove control knobs and console screws; lift off the old backsplash.
  • Transfer the timer/switches and any brackets to the new panel; move connectors one at a time or photograph wiring for reference.
  • Watch for sharp metal edges; avoid overtightening screws; control shafts are centered before reinstalling knobs.

Do-It-Yourself Stories from Customers like You Start switch broke   Walter G. • Chesnee , SC • November 14, 2016

Ordered new backsplash panel and replaced it , very easy fix Read more

More
$213.66
Compare At:
$254.26
You Save:
$40.60

IN STOCK
Ships Today Guaranteed
Add to Cart
Ge Dryer Control Panel Assembly (White)
Genuine Ge part
By: Ge
Part Number: WE19M1656

This control panel assembly replaces the white front console on your dryer. It restores a solid mounting surface for the timer, switches, or display so you can select cycles and settings with proper alignment and smooth operation. What it does

  • Provides the front console housing for the dryer's user controls
  • Keeps buttons/knobs and indicators aligned and protected
  • Restores appearance after cracks, discoloration, or broken tabs
  • Helpful when controls feel loose, are hard to press, or the console is rattling
What's included
  • 1 white control panel assembly
Install notes
  • Disconnect power; if gas, shut off the gas supply before servicing
  • Remove control knobs and any end caps; take out mounting screws/clips and lift off the old panel
  • Transfer any brackets, light pipes, clips, and harness retainers from the old panel to the new as needed
  • Reinstall and tighten fasteners; refit knobs and verify smooth control operation before restoring power

Do-It-Yourself Stories from Customers like You Front button had broken off   Scott L. • Miramar , FL • March 13, 2015

Replacing the control panel assembly is extremely easy with one exception. To take off the existing panel (and there is no way to order a button for this, you have to order and replace the entire assembly), you pull the dial knob off (it comes right off, no tools required). There's a single screw underneath, Phillips head. You can then slide the panel up, and then unplug the cable connecting the circuit board to the dryer itself. Next steps: Unscrew the half dozen or so screws to remove the... Read more

More
$241.95
Compare At:
$289.53
You Save:
$47.58

IN STOCK
Ships Today Guaranteed
Add to Cart
Ge Console Back Cover Assembly
Genuine Ge part
By: Ge
Part Number: WE19M1492

This console back cover assembly forms the rear housing of the dryer's control console. It supports the timer/controls and shields wiring so the control panel stays secure, aligned, and protected during everyday use.

  • Forms the rear shell of the control console
  • Provides mounting points for the timer/control board and switches
  • Protects and routes console wiring away from heat and debris
  • Helps keep knobs and buttons properly aligned and secured
  • Common signs it's needed: cracked plastic, broken tabs, or a loose/rattling console
What's included: 1 console back cover assembly Install notes:
  • Disconnect power to the dryer before servicing
  • Remove top/console fasteners per your model's service instructions and support the console
  • Transfer controls, brackets, and hardware from the old cover to the new one
  • Reattach all retainers/ground screws before reassembly and test

Do-It-Yourself Stories from Customers like You The started switch fell back into the back assembly faceplate i took it apart with just three screws to loosen and the problem was obvious the plastic tabs that held the switch had sheared off from   George B. • North Port , FL • October 30, 2017

Ordered the faceplate and just for insurance a new switch and know. The installation required a phillips screwdriver, a needle nose pliers, and about 10 minutes of time. Thanks to AppliancePartsPros for getting me the right parts asap...........George Read more

More
$198.53
Compare At:
$236.25
You Save:
$37.72

IN STOCK
Ships Today Guaranteed
Add to Cart
Ge Control Panel (Backsplash Assembly)
Genuine Ge part
By: Ge
Part Number: WE19M1486

This replacement control panel, also called the backsplash assembly, is the structural console on the rear of the dryer top where the timer and switches mount. It restores secure control mounting and a clean, finished appearance when the original is cracked or damaged.

  • Houses and supports the dryer's timer and control switches
  • Covers and helps protect console-area wiring from contact
  • Aligns control shafts through the panel openings for smooth knob operation
  • Common signs of failure: cracked panel, broken mounting tabs, loose or rattling controls
What's included: 1 control panel Install notes:
  • Disconnect power; for gas models, also shut off the gas supply
  • Remove control knobs and mounting screws, then tilt or lift the console to access the panel
  • Transfer timer/switches and any brackets from the old panel to the new one, keeping hardware organized
  • Do not overtighten screws; verify all controls turn and click freely before restoring power

Do-It-Yourself Stories from Customers like You Plastic console capture tabs and switch tabs broke plastic switch split   Nelson T. • Mobile , AL • April 26, 2016

Unplugged the dryer. Disconnected the exhaust hose w/ 5/16" nut driver. Removed all knobs. Removed 3 Phillips head screws behind the console. Removed all switches and controls by lifting locking tabs and turning counter clockwise. Installed switches and controls into new console by inserting into hole(s) and turning clockwise until locking tab engaged. Positioned console capture tabs back in their slots and snapped console back in place with the back plate. Re installed the tree screws. Re... Read more

More
$128.56
Compare At:
$152.99
You Save:
$24.43

IN STOCK
Ships Today Guaranteed
Add to Cart
Ge Backsplash Assembly
Genuine Ge part
By: Ge
Part Number: WE19M1485

This is a control panel.

More
$185.95
Compare At:
$221.28
You Save:
$35.33

IN STOCK
Ships Today Guaranteed
Add to Cart
Ge Back Assembly (Rear Cabinet Panel)
Genuine Ge part
By: Ge
Part Number: WE19M1494

This back assembly is the factory-style rear cabinet panel that protects and supports internal components. It restores the appliance's structural rear cover and helps keep internal parts safe from debris and damage. What it does

  • Replaces a damaged or missing rear cabinet panel to protect motors, wiring and electronics
  • Restores mounting points for components that attach to the back of the cabinet
  • Helps reduce air flow loss and limits access to internal parts that can cause shorts or damage
  • Common symptoms: visible dents or holes in the back panel, loose or rattling rear cover, or exposed components
What's included One back assembly Install notes
  • Disconnect power to the appliance before beginning any repair
  • Installation typically requires basic hand tools; handle edges carefully
  • Keep screws and fasteners from the original panel for re-use unless replacements are supplied

Do-It-Yourself Stories from Customers like You My dryer switch "died" and I needed a new "back asm" I decided to replace both.   Richard H. • Westfield , IN • November 04, 2020

I have replaced dryer switches before, and I knew how to put the other part on. It was a simple task, didn't need more than my screwdriver. Read more

More
$199.95
Compare At:
$237.94
You Save:
$37.99

IN STOCK
Ships Today Guaranteed
Add to Cart
Ge Backsplash Assembly (White)
Genuine Ge part
By: Ge
Part Number: WE19M1511

This white backsplash assembly restores the finished rear appearance of a range and helps protect the wall from spills, splatters, and heat. It provides a clean, factory-fit rear cover for affected models. What it does:

  • Covers and protects the rear wall area behind the range from grease, food splashes, and light heat exposure
  • Restores the appliance's factory appearance when the original backsplash is damaged or missing
  • Secures to the range frame to provide a finished mounting surface for rear components on applicable models
  • Prevents debris from entering gaps between the appliance and wall
What's included: One white backsplash assembly Install notes:
  • Disconnect power (and gas, if applicable) before beginning service
  • Remove screws or fasteners holding the old backsplash; save hardware for reassembly if reusable
  • Handle edges carefully; use proper hand tools and follow the appliance wiring/part diagram

More
$252.95
Compare At:
$301.01
You Save:
$48.06

IN STOCK
Ships Today Guaranteed
Add to Cart
Ge Switch Trim ( White )
Genuine Ge part
By: Ge
Part Number: WE19M1371

 

More
$59.88
Compare At:
$97.08
You Save:
$37.20

IN STOCK
Ships Today Guaranteed
Add to Cart
Ge Control Panel Assembly (Main)
Genuine Ge part
By: Ge
Part Number: WE19M1658

This control panel assembly replaces the oven's front console that houses the keypad and display, restoring user controls and readable status feedback for the range. It's a direct-fit console component used to operate oven functions. What it does:

  • Provides the front-mounted keypad and display interface for setting temperature, timers and oven modes
  • Replaces a cracked, unresponsive, or incorrectly displaying console to restore normal controls
  • Carries the underlying wiring connections and mounting points for secure installation
  • Works with the oven's electronic control board to send user commands
What's included: One control panel assembly Install notes:
  • Disconnect power at the breaker before starting any repair to avoid shock
  • Remove oven trim or mounting screws to access and unplug the existing control panel harness
  • Handle the display and glass surfaces carefully to avoid damage or fingerprints

More
$327.95
Compare At:
$390.26
You Save:
$62.31

Out Of Stock

Usually ships within 4 - 14 days

Add to Cart
Ge Control Panel Asm Wh
Genuine Ge part
By: Ge
Part Number: WE19M1427

 

More
$266.95
Compare At:
$321.67
You Save:
$54.72

Out Of Stock

Usually ships within 4 - 14 days

Add to Cart
Ge Back. Asm
Genuine Ge part
By: Ge
Part Number: WE19M1500

 

More
$186.32
Compare At:
$223.58
You Save:
$37.26

Out Of Stock

Usually ships within 4 - 14 days

Add to Cart
Ge Backsplash Assembly (With Graphic)
Genuine Ge part
By: Ge
Part Number: WE19M1553

This backsplash assembly with printed control graphic restores the finished rear/control area on a range or cooktop, improving appearance and protecting internal components from spills and splatters. What it does:

  • Replaces a cracked, dented, or faded backsplash and control graphic
  • Restores clear printed control markings used for settings and instructions
  • Helps protect underlying wiring and electronic components from grease and moisture
  • Reduces light glare and improves the appliance's finished look
What's included:
  • One backsplash assembly with printed graphic
Install notes:
  • High-level replacement; access usually requires removing rear panel or control console
  • Disconnect power (unplug or shut off breaker) before servicing to avoid shock
  • Handle edges and painted surfaces carefully to avoid scratches; use proper fasteners and gaskets where required
  • If the graphic aligns with electronic controls, confirm correct orientation before final fastening

Do-It-Yourself Stories from Customers like You Start switch would not stay mounted on backsplash   Elvin J. • La , CA • March 23, 2016

Replaced backsplash Read more

More
$150.14
Compare At:
$179.08
You Save:
$28.94

Out Of Stock

Usually ships within 4 - 14 days

Add to Cart
Ge Cntrl Pnl Asm Ms
Genuine Ge part
By: Ge
Part Number: WE19M1669

 

More
$283.75
Compare At:
$337.66
You Save:
$53.91

Out Of Stock

Usually ships within 4 - 14 days

Add to Cart
Ge Control Panel Assembly
Genuine Ge part
By: Ge
Part Number: WH46X10100

 

Do-It-Yourself Stories from Customers like You Computer module.   Alfriedo G. • Indianapolis , IN • July 18, 2017

Service was great they had to me in one day!? Read more

More
$264.95
Compare At:
$312.64
You Save:
$47.69

Out Of Stock

Usually ships within 4 - 14 days

Add to Cart

General Electric dryer touch pad replacement parts are an essential component for maintaining the functionality of your appliance. The touch pad plays a vital role in setting the drying cycles and ensuring that your clothes come out perfectly.

A General Electric dryer makes doing laundry simple and convenient in many households. The touch pad allows you to choose the right settings effortlessly. As it begins to wear out or malfunction, it can disrupt your laundry tasks. That's when high-quality replacement parts come into play. Choosing OEM (Original Equipment Manufacturer) General Electric dryer touch pads guarantees optimal performance and compatibility, restoring your dryer's efficiency.

It's reassuring to know that reliable General Electric dryer touch pads are readily available. These parts are designed to fit seamlessly and perfectly with your dryer, ensuring your laundry days remain hassle-free.

More
  • boxes images Over 2.1 Million Parts In Stock
  • time delivery images 2 Day Quick Delivery!
  • box-refresh images 365 Day Return Policy!
  • headphone imagesFree Tech Support!
  • google images Google Trusted Store