General Electric Dryer Heating Element

The Heating Element is an OEM replacement part for GE electric dryers. As the primary source of heat, it warm circulating air drying wet clothes efficiently.

Causes of failure may be surface fracturing and resistance loss due to deterioration over many heating cycles. Excessive mineral buildup may also hinder heat transfer capabilities.

Symptoms of a faulty element involve:

• Very long or inefficient drying times
• Unevenly dried clothes
• No heat detected during drying cycles

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Mica style heating element.

The Heating Element & Housing Assembly is an OEM part for GE dryers. This assembly includes the heating element, which is responsible for generating the heat necessary to dry clothes, and its housing, which protects and supports the heating element.

Causes of a bad heating element and housing assembly can include overheating, electrical faults, or wear and tear over time. These issues can lead to inefficient drying or complete failure of the heating element.

Symptoms of a bad heating element and housing assembly include:

• Clothes taking longer to dry than usual
• No heat being produced during the drying cycle
• The dryer shutting off unexpectedly

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Heating Element Assembly is an OEM part for GE dryers. It is responsible for generating the heat necessary to dry clothes during the drying cycle. This assembly includes the heating element itself, which heats up when electricity passes through it, and the housing that supports and protects the element.

You should replace this heating element assembly if it becomes faulty. Causes of a bad heating element assembly can include wear and tear over time, overheating due to blocked airflow, or damage from electrical issues.

Symptoms of a bad heating element assembly include:

• Clothes not drying properly
• No heat during the drying cycle
• Longer drying times
• The dryer not getting warm

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: For restring coil only use WE11X10007

This 240V heater assembly replaces the electric heating element module in your dryer, restoring proper heat to the airflow. Replacing a failed element helps address no-heat complaints and improves overall drying performance. What it does:

• Generates heat by energizing the element at 240 volts to warm air moving through the drum
• Restores heat when the original element is open or shorted to the housing
• Helps with: drum runs but no heat, long dry times, cool exhaust air
• Element should show continuity across its terminals and no continuity to chassis when tested

• 1 heater assembly

• Disconnect power before servicing; allow the unit to cool
• Access the heater housing from the rear or front, depending on model; photograph wiring for reference
• Move wires one at a time; reuse mounting screws; transfer any thermostats mounted on the old housing if present
• After reassembly, ensure the exhaust vent is clear to prevent overheating and repeat failures

The Dryer Heater Assembly is an OEM replacement part for GE dryers. It consists of the heating element and the necessary components to distribute and regulate the heat throughout the dryer drum.

Symptoms of a faulty dryer heater assembly include:

• Insufficient heat or no heat at all
• Extended drying times
• Burning smells during operation

A bad dryer heater assembly can be caused by normal wear and tear over time or damage due to blockages, electrical issues, or overheating. If you notice that your dryer is not heating properly, takes longer to dry clothes, or produces unusual odors, it may be time to replace the old or damaged heater assembly with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This heater assembly supplies the heating element and housing used in coin-operated dryers to produce the hot air needed for drying. Replaces a worn or failed heater module to restore normal drying temperatures and cycle performance. What it does:

• Generates and directs heat through the drum to dry clothes
• Heats only when the dryer control and motor are running
• Commonly replaced when a dryer tumbles but produces little or no heat
• Also used when a dryer trips thermal cutouts or has intermittent heating

• One heater assembly (housing with heating element and mounting hardware)

• Disconnect power before starting — this is a live-voltage component; verify power is off
• Follow dryer service manual for access, removal, and wire/harness routing
• Inspect and replace any failed thermal fuses or thermostats per OEM guidance

The oven control and overlay assembly are installed directly in the front of the main console of the oven. They contain the control interface of the appliance. When the overlay assembly and control interface malfunction, normally, the backlight goes out behind the console. The user is unable to see any controls or function information. This malfunction can be caused by electrical short or external damage. It's possible a fuse could be the problem, and a voltage tester can give you a clear indication of where the problem lies. Begin the installation by unplugging the oven first. Using a screwdriver, unthread the screws around the perimeter of the main user interface. This will allow the casing around the console to come off. On the rear of the oven, remove the screws holding the back panel in place until the control board can be seen. Unscrew the control board assembly from the control overlay assembly. Repeat these steps in reverse with the new part.This GE oven control and overlay assembly is a genuine OEM product sourced directly from the manufacturer. The listed product is sold individually. This part is compatible with GE, Kenmore, HotPoint, RCA, and Kenmore.

This genuine dryer heater assembly heats the air inside the dryer so clothes dry efficiently. It replaces a failed heating element to restore normal drying performance and reduce extended drying cycles. What it does:

• Generates the heat required for the dryer to remove moisture from laundry.
• Restores normal drying times when a worn or broken element causes little or no heat.
• Works with the dryer's thermal controls to maintain safe operating temperatures.
• Can stop dryer trips or error conditions caused by an open or shorted element.

• One dryer heater assembly (heating element)

• Disconnect electrical power to the dryer before beginning any work.
• Handle the element carefully — avoid bending or contacting the coil with sharp tools.
• Inspect and, if necessary, test the thermal fuse, thermostats, and wiring; replace any failed safety components.

This heater assembly is an integral part of many dryers. It is typically located within a housing and heats up air as it moves through the blower. It may sit behind the dryer drum and heat the air in that manner. If the air in the dryer never gets hot or it takes extra time to dry a load of laundry, this could be an indication that the heater assembly is damaged or malfunctioning. The heater assembly can be tested, but if damaged, it should be replaced with an OEM part.Make sure the dryer is unplugged from the outlet before starting. Loosen the vent clamp screw to release the vent behind the appliance. Pull out the dryer for easier access to the back. Access the heater assembly in the dryer by disassembling the appliance. Remove the wires from the high-limit thermostat and heater assembly terminals. Remove the heater assembly and replace it with the new component. Make sure to reassemble all other parts before returning power to the appliance to test it.Compatible with GE dryers, the heater assembly is directly sourced from the manufacturer. This part is sold as an individual item. It is a genuine OEM replacement part.