General Electric Dryer Control Board

The Timer is an OEM part for GE dryers that is responsible for ensuring that the dryer operates for the set amount of time, enabling different cycles and functions to occur at the correct intervals. The timer regulates the start, duration, and end of each drying cycle. Over time, timers can wear out or malfunction due to electrical issues or mechanical wear, leading to problems with the dryer's operation.

Symptoms of a bad Timer include:

• The dryer failing to start or stop at the proper times.
• Only certain cycles working.
• The dryer running continuously without shutting off.

Causes of a bad timer can stem from a variety of issues, including electrical shorts, worn contacts within the timer mechanism. Regular usage and age can contribute to these problems.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Dryer Timer is an OEM part for GE dryers. It controls the duration of the drying cycles by regulating the flow of electricity to the dryer’s motor and heating element. The timer ensures that clothes are dried for the correct amount of time based on the selected cycle, contributing to efficient and effective drying.

Causes of a bad dryer timer can include electrical failures, wear and tear from frequent use, or internal mechanical issues. A malfunctioning timer can result in improper drying times and affect the performance and efficiency of the dryer.

Symptoms of a bad dryer timer include:

• Dryer not starting or stopping at the correct times
• Dryer running continuously or not advancing through cycles
• Inconsistent drying results
• No clicking sound from the timer during operation

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Dryer Timer is an OEM replacement part for GE dryers. It is a crucial component that controls the timing and sequence of the various cycles and functions within the dryer, ensuring proper operation and efficient drying performance. The timer measures approximately 2 3/4" H x 3" W x 4 1/4" D,

Symptoms of a faulty dryer timer can include:

• The dryer not starting or running at all
• The dryer failing to progress through cycles or shutting off prematurely
• Cycles running for an incorrect or inconsistent amount of time
• Error codes or indicators related to the timer or control system

Causes of a bad dryer timer can range from electrical issues, such as short circuits or failed components, to mechanical wear and tear over extended use, or physical damage from impact or mishandling.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. 

The Timer is an OEM part for GE dryers. It is responsible for controlling the duration of the drying cycles by regulating the flow of electricity to the heating element and the motor. The timer ensures that clothes are dried for the correct amount of time, based on the selected cycle.

Causes of a bad timer can include electrical failures, wear and tear from frequent use, or internal mechanical issues. A faulty timer can result in improper drying times, which may affect the performance and efficiency of the dryer.

Symptoms of a bad timer include:

• Dryer not starting or stopping at the correct times
• Dryer running continuously or not advancing through cycles
• Inconsistent drying results
• No clicking sound from the timer during operation

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Timer is an OEM part for GE dryers. It controls the length of the drying cycles by advancing through the cycle's various stages, including drying, cool down, and finish. This component ensures that the dryer operates for the correct amount of time based on the selected settings.

You should replace this timer if it malfunctions or fails to progress through the cycle stages properly. Common causes of a bad timer include electrical failures, worn contacts within the timer mechanism, or damage from repeated use over time.

Symptoms of a bad timer include:

• Dryer not advancing through cycles
• Dryer stopping prematurely or running continuously
• Inconsistent drying times
• Timer not moving or making unusual noises

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This timer is the cycle control for your dryer, advancing through the settings and switching circuits on and off as selected. Replacing a failed timer restores accurate cycle timing and dependable start/stop control.

• Advances the dryer through the selected cycle and turns it off at the end
• Routes power to components according to the timer cam and contacts
• Supports timed and automatic cycles selected by the control knob
• Common symptoms: timer doesn't advance, dryer runs too long or won't shut off, stops mid-cycle, or won't start on certain settings

• Disconnect power to the dryer (and shut off gas supply for gas models) before servicing
• Access the control console; photograph/label wiring and transfer terminals to the new timer one at a time
• Reuse existing knob and mounting hardware; ensure the timer shaft is oriented correctly before reassembly

This electronic control board governs your dryer's cycle logic and responses. Replacing a failing board restores proper communication between the controls and internal components to help resolve dead console, no-start, or erratic cycle behavior.

• Interprets cycle selections and sensor inputs to run the programmed operations
• Sends control signals to the dryer's components as designed by the model
• Coordinates timing and status indicators
• Common symptoms: won't start, console unresponsive, cycles that won't run/advance/end properly, intermittent power or random lights/beeps

• Disconnect power before servicing; this board carries line voltage.
• Use ESD precautions and handle the PCB by the edges.
• Photograph/label connectors and move wires one at a time to the new board; secure with existing bracket.
• After installation, run the model's diagnostic or test routine if applicable.

This timer controls the drying cycle by advancing through settings and routing power to the motor and heater. Replace a worn timer if the cycle won't advance, runs indefinitely, or stops unexpectedly on certain selections.

• Advances the dryer through timed/auto cycles and sets overall cycle length
• Directs power to motor and heater according to the selected program
• Coordinates cycle start/stop and end-of-cycle shutoff
• Failure symptoms include: timer not advancing, dryer runs but won't shut off, stops mid-cycle, or won't start on certain settings

• Disconnect power before servicing
• Access the timer from the control panel; retain and reuse original mounting screws
• Move wires to the new timer one at a time; label or photograph connections for reference
• Reassemble and test all cycle selections for proper advance and shutoff

This dryer timer controls the length and sequence of drying cycles. Replacing a failed timer restores proper cycle advancement so the dryer starts, runs, and shuts off at the correct time.

• Controls cycle timing and progression through the selected settings
• Opens/closes internal contacts to route power to the drive motor, heat circuit, and end-of-cycle signal as designed
• Advances the control dial and stops the dryer at the OFF position
• Typical symptoms of a bad timer: timer won't advance, dryer runs too long, stops mid-cycle, or won't start on timed cycles

• Disconnect power before servicing; for gas dryers, also shut off the gas supply
• Access timer from the control panel; remove the rear panel/cover to reach it
• Label or photograph wire positions and transfer them one-by-one to the new timer
• Secure the timer with original screws, reinstall the dial/knob, and test cycle operation

This replacement dryer timer controls cycle selection and run time. The plastic-shaft version restores positive knob engagement and timing control for reliable cycle advancement and shutoff.

• Advances the dryer through timed cycles and ends the cycle at the selected setting
• Directs power to the correct circuits as the cycle progresses
• Common symptoms: timer won't advance or stops mid-cycle
• Knob spins, slips, or won't engage the timer; dryer runs too long or won't shut off

• Disconnect power; if gas, also shut off the gas supply
• Access the timer from the control panel; remove knob and panel as needed
• Move wires from the old timer to the new timer one at a time to matching terminals
• Mount the timer securely, reassemble the console, reinstall the knob, and test operation

This plastic timer shaft connects the control knob to the dryer's timer. It restores a secure, positive engagement so you can reliably select cycles and turn the timer without the knob slipping or wobbling.

• Couples the control knob to the timer mechanism
• Allows accurate turning of the timer to select settings
• Replaces a cracked or stripped shaft that causes the knob to spin freely
• Helps keep the dial aligned with the chosen cycle

• Disconnect power to the dryer before servicing
• Pull off the timer knob and dial; access the control panel if needed
• Align the new shaft with the timer stem (match flat/splines) and press straight on—do not force
• Reinstall the dial and knob; verify the knob turns the timer smoothly

This replacement part is a control board that has been manufactured by General Electric and is compatible with dryers. This part works by allowing the user to select the desired functions such as the drying time or the temperature. Control boards are subject to wear and tear over time, which may cause them to deteriorate or become faulty, requiring replacement. Before attempting any sort of repairs, ensure that the dryer has been entirely disconnected from all power sources to prevent the risk of injury, particularly from electrocution. Work gloves should also be worn.This is a genuine OEM part that has been sourced directly from the manufacturer. This is an authentic part made of high-quality, durable, non-corrosive materials and is compatible with dryers manufactured by General Electric, Hotpoint, RCA, and some other brands. This part is only sold individually.

Replacement electromechanical oven timer that restores timed-cooking control on compatible GE ranges and wall ovens. Use it to regain reliable cycle timing for bake, broil and self-clean functions. What it does:

• Advances and times oven cooking cycles so timed bake/broil and self-clean operations run as expected.
• Common symptoms: timer does not move, timed cycles do not start or finish, or oven won't complete a timed cooking cycle.
• Replaces a failed mechanical timing mechanism in the oven control console; interfaces with existing console wiring and mounting.
• Verify model compatibility using your appliance model number before ordering.

• Disconnect power to the appliance at the circuit breaker before beginning any repair.
• Label or photograph wire locations before removal to ensure correct reconnection.
• Use basic hand tools and avoid forcing connectors; handle the assembly carefully.

This dryer timer controls the length of the drying cycle and directs power to key circuits. Replacing a worn timer restores reliable cycle advance and proper shutoff so the dryer doesn't run too long or stall.

• Advances the dryer through the selected timed cycle and turns it off at the end of the set time
• Routes power to the drive motor and heating circuit through internal switch contacts
• Coordinates cycle selection via the control knob attached to the timer shaft
• Failure symptoms include: cycle not advancing, running continuously, won't start on certain settings, or intermittent/no heat

• Disconnect power before servicing; if gas, also shut off the gas supply
• Access the control panel and remove the rear cover to reach the timer
• Photograph/label wires and transfer them one by one to matching terminals on the new timer
• Mount the timer securely, align the shaft, reinstall the knob/dial, and test all cycle positions

This genuine replacement part is a user interface board for dryers. The user interface board is the circuit board that responds to the buttons located on the control panel allowing the user to adjust the dryer settings. If the dryer is no longer responding when buttons are being pressed then it might be time to replace the user interface board. Luckily this is a relatively easy repair.To replace the interface board begin by turning off the power to the dryer. Once the power has been shut off move the dryer away from the wall to gain access to the upper back panel. Remove the panel and locate the interface board. Snap it out of its brackets and remove the wire harness attached to the board. Reinsert the wire connector to the new interface and snap the new board assembly back to its original place.This OEM replacement part is sold individually and is compatible with General Electric, Hotpoint, and RCA brand Dryers.

This dryer timer controls the sequence and length of your dryer's cycles. Replace it to restore accurate cycle timing, reliable start/stop, and automatic shutoff when the dial no longer advances or the dryer runs indefinitely.

• Controls power to the motor and heater through timed internal contacts
• Advances the selected cycle and turns the dryer off at the end
• Provides cycle selections through the front dial
• Typical symptoms: cycle won't advance, runs continuously or stops too soon, won't start on certain settings, or no heat on specific timer positions

• Disconnect electrical power before servicing; for gas models, also shut off the gas supply
• Access the rear of the control panel/console to reach the timer
• Transfer wires from the old timer to the new one one-by-one, matching terminal markings; move the mounting hardware and dial as needed
• After installation, test multiple cycles for proper advance and shutoff