Need Help?
Call or text
Replace a missing, bent, or damaged convection oven rack in your microwave. Provides a stable cooking surface for baking and roasting in convection mode.
Replaced grill and twist on grill supports. Stopped shorting and works fine now. Read more
Microwave not heating or humming loudly? The high-voltage diode converts AC to DC for the magnetron. Repair takes 30-45 minutes with basic tools.
I replaced both the Magnetron and the high voltage diode. I now have a fully functional microwave. I received the parts on time and the quality was good. I would use appliance parts pro's again. Read more
The Door Latch Board is an OEM part for GE microwaves. The latch board controls the door latching mechanism that secures the microwave door closed during operation. It works alongside the door interlock switch to initiate the removal of power to the ma
We isolated the problem via YouTube videos to a faulty switch. We broke a piece of the switch holder when removing the switch and had to also order that part in addition to a new switch. Once everything was reassembled, the microwave worked again! Read more
Microwave not heating? The magnetron generates the microwaves that heat food. Common repair for units that run but don't warm. DIY-friendly repair.
Replace magnetron. Took longer to remove and disassemble m/w than to replace part. Above range installation. M/w was heavy- be careful. Read more
The Thermostat is an OEM part for GE microwaves. This thermostat maintains safe operating temperatures by monitoring the internal heat levels and regulating the microwave's heating elements.
Causes of a bad thermostat can include ele
I researched the problem and found that not only was the fuse blown but the cause was a bad thermostat. Using the model number AppliancePartsPros.com. sold me the right parts for the right job. Read more
This is an authentic OEM replacement waveguide sourced directly from the manufacturer. Waveguides are used in microwave ovens to help transmit the radiation throughout the microwave's inner cavity. The waveguide also protects the microwave's inner parts f
After looking at your site, the parts diagram, and consulting via chat, we ordered the wave guide replacement part. Installed the new wave guide and the appliance works perfectly. We also cleaned the inside of the appliance per the instructions in the guide. Read more
Clear glass lens cover for over-the-range microwave cooktop light. Shields bulb from grease and splatters. Replace if cracked, broken, or missing.
We ordered the parts we needed & they came right away. My husband installed them the day they came. Voila! Perfect! Read more
Supports the removable rack inside your microwave cavity. Replace this holder if it's cracked, melted, missing, or broken to restore proper rack positioning.
I remove the burnt melted rack holder and replaced it with the new one I ordered. I watched the how to repair on YouTube and was able to remove it with a pair of pliers and install the new rack holder. It was very easy to install. Read more
Captures grease particles during cooking to maintain air quality and microwave efficiency. Replace when clogged or discolored. Verify fit with your model.
My particular model of microwave had one screw visible but the other hidden behind a plastic ring. I needed to pop the ring out by disengaging the plastics clips using a putty knife; then it was an easy job of unscrewing the old handle and screwing the new one in. It probably took me just as long to write this description as it did to actually replace the handle. Read more
This microswitch senses the microwave door position and controls the safety interlock circuits. Replacing a worn switch restores proper start/stop behavior so the oven only runs when the door is fully closed.
By replacing the switches. Read more
This rivet assembly is a direct-replacement fastening piece used to secure appliance panels and components, restoring a stable, rattle-free fit and preventing movement caused by worn or broken rivets. What it does:
I replaced the stirrer fan cover and fan, which had some carbon and slight burn marks on it. It was difficult to remove the fan cover as it did not rotate. I had to pry it off with a flat blade screwdriver, breaking the plastic tabs on the cover (which was being discarded anyway). I then cleaned any visible carbon deposits and replaced the cover and fan, using the old stirrer fan holder as it appeared OK. However, I was unable to rotate the cover into the locked position so I could not insert... Read more
Replacement glass turntable tray for microwaves. Sits on the roller ring to rotate dishes during cooking. Order when original is cracked or broken.
I ordered a replacement tray from you. Great service. The part arrived quickly. Read more
Grease filter captures cooking vapors and prevents buildup in your microwave. Replace when discolored or grease-coated. Verify fit with your model number.
I ordered part from you and replaced old part I ordered on a Friday afternoon (late ) and was pleasantly surprised to receive the very next day!!!!!! Read more
Replace your microwave's grease filter to maintain proper ventilation and capture cooking grease. Easy snap-in installation. Verify fit with your model number.
Sooooooo easy Read more
Microwave runs but won't heat? This magnetron generates the RF energy that cooks food. Moderate DIY repair, typically completed in about an hour.
After some research, and based on the symptoms, consulted with repair person and figured it was the most common 3 parts (magnetron, capacitance, diode, and threw in a new fuse). So spent $190, and service tech came, replaced them, all good again. All done in an hour. Read more
Microwave not heating but runs? Replace the magnetron to restore cooking power. Intermediate DIY repair taking 1-2 hours with proper safety steps.
I ordered the capacitor, diode, and magnetron in hopes that I would be able to complete the repair using the less expensive parts. I first removed the oven from the wall and then I removed the metal housing to access the internal parts. I discharged the capacitor using a pair of insulated needle nose pliers. Then I changed out the diode and the capacitor and reassembled the unit and tested it. It still did not heat so I disassembled the unit again and replaced the magnetron this time.... Read more