General Electric Range / Cooktop / Oven Burner & Related Parts

15K

This circuit board mounting bracket secures an electronic board or module inside the appliance. It prevents movement, vibration damage, and wiring interference so the component stays correctly positioned for reliable operation.

• Mounts and supports a small circuit board or module within the chassis
• Maintains proper spacing and alignment to reduce chafing or electrical short risks
• Replace if bent, cracked, or missing tabs, or if it no longer holds the board securely
• Common signs include a loose/rattling board, visible bracket damage, or intermittent operation when the panel is bumped

• Disconnect power at the breaker; shut off gas supply if applicable
• Remove the necessary access panel(s) to reach the board and bracket; note orientation and wiring
• Transfer the board/module to the new bracket and reinstall using existing hardware
• Watch for sharp metal edges; route wires to avoid pinching and verify clearances before restoring power

Approx 2-1/2 inches in diameter

This head burner main is the primary gas burner head used on compatible gas ranges to direct and distribute the flame for proper cooking. It replaces a damaged or corroded burner head to restore even heating performance. What it does:

• Directs gas to the cooktop for ignition and controlled flame distribution
• Helps maintain even heat across the cooking surface for consistent results
• Can resolve symptoms like uneven flame, visible damage, or poor ignition at the burner
• Works with the burner cap and valve assembly as part of the burner system

• Turn off gas supply and power to the appliance before starting any work
• Remove grates and burner caps to access the burner; follow OEM disassembly guidance
• Replace only with the exact part number to ensure proper fit and function

18K Simmer

This surface burner cap is a genuine General Electric part, sold individually. It can be used as a replacement part for a gas range. This surface burner cap provides a covering for the burner of the gas range so that the infrastructure of the burner and the ignition are not damaged in the process of utilizing the burners.A surface burner cap might have to be replaced if it is lost, misplaced, or has suffered damage that prevents the component from protecting the burner and the ignition. Damage can include punctures, cracks, chips, or erosion to the material that weakens the ability of the component to protect the burner and ignition. If this damage occurs, the component should be removed and replaced by this genuine OEM replacement part. It is a simple replacement process that will require no special tools.This is an OEM part sourced directly from the manufacturer. It is sold individually. This surface burner cap is compatible with General Electric brand gas ranges.

This small cooktop bracket secures designated components beneath the cooktop surface, keeping them properly positioned and stable. Replace a damaged or missing bracket to restore alignment and reduce movement or rattling during use.

• Provides mounting support for specific under-top components, per model design
• Helps maintain proper alignment and stability of cooktop parts
• Replace when visibly bent, cracked, or corroded

• Disconnect power; for gas models, also shut off gas and allow the unit to cool
• Remove surface components as required (grates/caps/heads for gas; elements/panels for electric) to access under the top
• Lift or remove the cooktop as directed in your model's service information and secure the new bracket with existing hardware
• Reassemble, verify alignment, and for gas units check for leaks if any gas connections were disturbed

Black. C Burner

Approx 1-1/2 inches in diameter

Black. B Burner

This bake burner is the oven's main gas tube that produces steady heat for baking and roasting, restoring proper cooking temperatures and more consistent bake results. It fits gas ovens that use a separate bake tube assembly. What it does

• Directs and distributes the oven's gas flame to generate baking heat
• Restores proper oven temperature when the bake flame is weak or absent
• Helps eliminate uneven baking or undercooked dishes caused by a failing tube
• Works with the oven igniter and gas valve to light the burner safely

• One bake burner (bake tube) as shown

• Turn off gas supply and electrical power before starting work
• Removal may require disconnecting burner mounting screws and any brackets; keep track of fasteners
• Inspect and replace related parts (igniter, orifice) if ignition problems persist

This burner cap sits over the gas burner head to focus and evenly distribute the flame on your cooktop or range. Replace a missing, chipped, or warped cap to restore smooth ignition and consistent, efficient heating.

• Shapes and diffuses the burner flame for even heat across cookware
• A properly seated cap promotes fast, reliable ignition
• Shields the burner head from spills and debris for consistent performance
• Replaces damaged or missing caps that can cause uneven/yellow flames, delayed ignition, or clicking without lighting

• Disconnect power and shut off gas; allow the surface to cool completely
• Lift off the old cap and clean the burner head/ports before installing
• Match the cap to the correct burner position for your model; caps are size-specific
• Seat the cap flat and centered, then test ignition and flame pattern

This hot-surface bake oven ignitor lights the gas burner for the oven so it reaches and holds baking temperatures. Replaces a weak or failed ignitor to restore reliable oven heating and consistent cooking results. What it does:

• Heats until hot enough to ignite the oven's gas burner for bake operations
• Restores normal preheat times and consistent oven temperature when the ignitor is failing
• Helps eliminate symptoms such as oven not heating, very slow preheat, or burner not staying lit
• Works as the direct ignition source for the bake burner assembly

• One bake oven hot-surface ignitor (WB13K10013)

• Disconnect power to the appliance and shut off the gas supply before starting work
• Handle the ceramic/glass element carefully—it's fragile and can crack if dropped or touched with bare hands
• Verify correct replacement part number for your appliance and test for gas leaks after installation

This burner base secures a cooktop's surface burner assembly and helps position the burner head for consistent flame and stable cookware support. Replace a damaged base to restore proper burner alignment and consistent heating performance. What it does:

• Supports the surface burner head and cap so the flame stays centered under cookware
• Helps position and channel the burner assembly for even ignition and heating
• Restores stable seating when a warped or cracked base causes wobbling
• Common symptoms: uneven or wandering flame, loose/wobbly burner cap, or burner that won't light reliably

• Always disconnect power and shut off gas supply before servicing a gas cooktop
• Handle parts carefully to avoid bending tabs or stripping fasteners; keep removed screws and caps together
• After installation, verify proper burner alignment, ignition, and flame pattern before regular use

12K

This burner base restores consistent flame and reliable ignition on your gas cooktop or range. It routes gas from the orifice through the burner ports and supports the cap and igniter for even, dependable heat.

• Directs gas from the orifice through burner ports for a stable, even flame
• Provides the seating surface for the burner cap and alignment for the igniter electrode
• Helps ensure quick, reliable lighting when clean and intact
• A worn, cracked, or clogged base can cause weak/uneven flames, delayed ignition, or burners that won't light

• Shut off gas supply and power; allow the surface to cool completely
• Remove grates and burner caps; take out mounting screws and lift off the old base
• Protect the igniter electrode; transfer any reusable screws or gasket as needed; set the new base flat over the orifice holder
• Reassemble, restore gas/power, and test for proper ignition and flame; check connections with a leak-detection solution