General Electric Range / Cooktop / Oven Hinge Parts

This right-side hinge assembly secures and guides the appliance door for consistent opening and closing, restoring proper alignment and sealing. It's a direct-fit replacement when the door feels loose, binds, or won't stay aligned. What it does:

• Supports the door on the right side and maintains correct pivoting motion
• Restores proper door alignment to improve closing and sealing
• Helps eliminate sagging, binding, or uneven gaps during operation
• Works with existing hinge pins and mounts where applicable

• Replace both hinges if the left-side hinge shows similar wear; balance is recommended for long-term alignment
• Disconnect power and remove any panels or door components per manufacturer instructions before starting
• Use proper tools and keep fasteners organized; tighten to OEM torque if specified

This left-side refrigerator door hinge secures and pivots the door for smooth opening and proper alignment. It restores stable door movement and helps maintain a tight seal to protect internal temperatures and food freshness. What it does:

• Provides a mounting point for the refrigerator door and allows it to swing open and closed
• Keeps the door aligned to ensure consistent sealing and energy efficiency
• Replaces worn, bent or broken hinges that cause sagging, rubbing or uneven gaps
• Works with factory hinge pins and fasteners to restore original door operation

• Intended for the left-side door; verify orientation before installation
• Installation requires basic hand tools and safe handling of the door to avoid damage or injury
• If needed, support the door or have a helper during removal and reattachment to prevent dropping
• Inspect hinge mounting screws and surrounding trim; replace hardware if stripped or damaged

This right-side door hinge secures and guides the appliance door for correct alignment and smooth operation. Replacing a worn hinge restores proper closing and prevents door sag or uneven gaps. What it does:

• Supports the door pivot and maintains correct door alignment.
• Enables smooth opening and closing of the door.
• Prevents door sag, binding, or misaligned gaps that can affect seal performance.
• Helps eliminate rubbing, scraping, or unusual door movement.

• Disconnect power to the appliance before starting and remove any stored items from the door.
• Support the door while removing/installing the hinge to prevent dropping or damage.
• Reuse existing screws only if they are undamaged; replace damaged fasteners.
• Check door alignment after installation and make minor adjustments as needed for an even seal.

This hinge provides the pivot point for the appliance door, keeping it aligned so it opens and closes smoothly. Replacing a bent or broken hinge restores proper latching, sealing, and overall door operation.

• Provides the pivot and support for smooth door opening and closing
• Maintains alignment so the latch and door switches engage correctly
• Helps ensure an even seal to prevent heat or air leaks
• Common symptoms: door sags, rubs, or won't close/latch; appliance won't run/heat because the door isn't engaging

• Disconnect power to the appliance before servicing
• Support the door to prevent strain on the remaining hinge while removing hardware
• Install the new hinge in the same orientation; transfer any screws or bushings from the original
• Verify door alignment and latching before restoring power

Left hand side. For right hand use WB14K5006

The Door Hinge (Left) is an OEM part for GE gas ranges. This hinge is responsible for securely and smoothly mounting the oven door to allow easy access to the cooking cavity. 

Causes of a bad hinge include normal wear and tear from years of opening and closing the heavy oven door. The repeated motion can cause hinge mechanisms to loosen, fail to properly support the door weight, or become misaligned over time.

Symptoms of a bad hinge (left) include: 

• The oven door sagging or unable to stay open on its own  
• Difficulty smoothly opening and closing the door
• Noisy or gritty motion from the hinge when in use
• Improper alignment that impacts sealing of the door

This genuine GE replacement hinge is compatible with some Hotpoint and RCA models as well. 

This is the right side broiler hinge. For left side use WB10K6.

This is the left side broiler hinge. For right side use WB10K5.