General Electric Tray & Related

Removable wire rack creates a second cooking level in compatible microwaves. Replace missing, bent, or chipped racks to restore multi-item capacity.

Metal tray that sits inside the microwave cavity to support food during cooking. Replace if warped, damaged, or missing to restore a stable surface.

This auxiliary cooktop holder is a replacement support bracket that helps keep the cooktop or burner assembly aligned and secure for stable, rattle-free operation. Restores proper positioning of components after wear or damage. What it does

• Supports and anchors the cooktop/burner assembly to prevent shifting during use
• Keeps burner and trim pieces aligned for even surface contact and safe operation
• Reduces rattling, vibration, and gaps between cooktop components
• Helps restore secure mounting after broken or worn original brackets

• Disconnect power (and gas, if applicable) before starting any repair
• Use proper hand tools; part secures with fasteners—retain and reinstall all screws
• Watch for sharp sheet-metal edges and wear safety gloves and eye protection

Supports the removable wire rack inside your microwave cavity. Replace this holder if cracked, broken, or missing to restore stable two-level cooking capability.

This flat metal tray is a replacement nonstick oven tray that gives you a flat cooking or drip surface for baking and roasting. It restores a level surface for pans and helps contain spills for easier cleanup. What it does:

• Provides a flat, rigid surface for baking, roasting, or catching drips beneath racks
• Restores proper fit when original tray is bent, warped, or missing
• Helps reduce food contact with oven floor and collects spills to prevent messes
• Nonstick finish eases cleanup when coating remains intact

• Install on the oven rack or support as shown in your owner's manual; ensure it sits flat before heating
• Allow tray to cool before handling to avoid burns
• Do not use abrasive pads or metal utensils on the nonstick surface to avoid damaging the coating
• Inspect coating for chips or flaking; replace if coating is compromised to avoid contamination

Connects the motor to the glass tray for smooth turntable rotation. Replace if your shaft is broken, worn, or causing the tray to wobble or scrape.

This is a nonstick metal grill tray designed for use in a microwave or combination cooking appliance. It serves as a cooking surface that allows grease and drippings to drain away from food during grilling or broiling functions. Replace this tray if the nonstick coating is peeling, the metal is warped, or the grill no longer sits properly on the turntable.

Replacement drive coupler for microwave turntable systems. Connects motor to turntable shaft. Replace if cracked, stripped, or broken to restore rotation.

This wire rack assembly provides a sturdy, removable shelf for your oven, giving stable support for cookware and bakeware and restoring proper shelf placement and clearance. What it does

• Replaces a bent, damaged, or missing oven shelf so pots and pans sit level during baking and roasting
• Restores smooth sliding and correct clearance for consistent cooking results
• Helps prevent cookware from tipping or shifting on weakened racks
• Fits into existing rack supports or side rails for secure positioning

• Remove power to the appliance and allow it to cool completely before installing
• Slide the rack into the oven rails or supports until fully seated; it rests level
• Wear gloves to avoid pinches or sharp edges while handling the rack
• No special tools usually required; refer to your owner's manual for model-specific guidance

Nonstick grille tray pan for microwave ovens with broiling/grilling capability. Replace your cracked, worn, or missing tray for even cooking results.

This glass tray is a flat oven shelf that provides a smooth, easy-to-clean surface for baking and roasting. It restores a stable cooking surface and replaces cracked, chipped, or otherwise damaged oven glass trays. What it does:

• Supports bakeware and cookware for even heating on the oven floor or shelf area
• Replaces trays that are cracked, chipped, or shattered and may cause uneven cooking
• Provides a smooth, non-porous surface that's simple to wipe clean
• Helps prevent food drips from contacting the oven floor when used as intended

• One glass tray

• Handle carefully; glass can break and cause injury—wear cut-resistant gloves
• Allow the oven to cool completely before removing or installing the tray
• Inspect tray for chips or stress cracks before first use; do not use if damaged
• Follow the appliance manufacturer's instructions for placement and safe use

Supports and stabilizes the microwave turntable for smooth rotation. Replace if roller is worn, cracked, or causing uneven spinning. Includes roller and bracket.

Plastic coupler that connects the turntable tray to the motor shaft in your microwave. Replace if cracked, broken, or worn to restore smooth rotation.

Microwave turntable coupler that connects the motor shaft to the glass tray. Replace if cracked, broken, or worn to restore proper tray rotation.

Replacement turntable tray rack assembly for your microwave. Installs on the rotating base to support the glass tray. Order when cracked or broken.

This cooking tray is the oven broiler/drip pan that catches drips and holds food while broiling, helping keep the oven interior cleaner and making broiling tasks easier. It provides a stable surface for broiling and roasting. What it does:

• Catches grease, juices and food debris to help prevent spills and reduce smoking
• Supports pans or food under the broiler for even browning and crisping
• Helps contain messes for easier cleanup after cooking
• Restores proper fit and function when the original tray is damaged or warped

• One cooking tray

• Install on the broiler rack or designated support slots; ensure tray sits flat and secure before use
• Allow the oven to fully cool before removing or installing the tray to avoid burns
• Clean with warm, soapy water and avoid abrasive cleaners that can damage the finish
• Inspect regularly for heavy warping or damage; replace if it no longer fits securely