General Electric Nameplate, Faceplate

This faceplate is the front cover for the control panel. It restores a finished look and helps protect and support the control assembly so the controls align and operate correctly.

• Covers and shields the control assembly from everyday use
• Provides secure mounting and proper alignment for controls
• Replace if cracked, warped, or if mounting tabs are broken
• Common signs include a loose or missing cover, rattling panel, or misaligned controls

• Disconnect power at the breaker before servicing
• Remove screws/retainers to lift the control panel; support the board and wiring
• Transfer any existing brackets or clips to the new faceplate as needed
• Reinstall, restore power, and test

This logo badge is the decorative nameplate used on select cooking appliances. Replacing a missing or worn emblem restores the finished factory look and keeps the front of your appliance looking complete and consistent with the original design.

• Cosmetic component that displays the appliance logo and completes the front panel or door
• Replaces a badge that is missing, cracked, peeling, or discolored
• Helps refresh the appliance's appearance without affecting operation
• Common signs: badge fell off, won't adhere, looks faded or damaged

• Disconnect power before working near control panels or doors
• Note the badge's original location and orientation before removal
• Use a non-marring tool to gently lift the old emblem if present; avoid scratching finishes
• Clean and dry the surface thoroughly before pressing the new badge into place

This center trim is the molded bezel that fits the front center of the cooktop/oven control area, restoring a finished look and protecting the control panel edges from heat and grime. What it does:

• Covers and protects the exposed edge of the control panel for a clean appearance
• Hides gaps, chips or discolored trim that make the console look worn
• Helps prevent dirt and grease from getting behind the control assembly
• Restores proper alignment and fit where the original trim is cracked or broken

• Disconnect power to the appliance before starting any repair.
• Typically secures with clips or screws—retain hardware and note orientation when removing old trim.
• Handle edges carefully; replacement may require gentle prying with a trim tool.
• If mounting hardware or support brackets are damaged, replace them separately.

This replacement faceplate restores the front control panel appearance and provides a secure mounting surface for the console buttons and display. It helps keep controls aligned and protects internal components from spills and wear. What it does:

• Replaces a cracked, warped, or cosmetically damaged control panel faceplate
• Provides a flat, stable surface so buttons and touch controls operate correctly
• Helps prevent spills and debris from reaching internal electronics
• Restores original fit-and-finish for a clean, factory appearance

• Disconnect power (unplug appliance or switch off circuit) before starting any work
• Removal typically requires loosening console screws or clips; keep track of fasteners
• Handle carefully to avoid scratching the finish or damaging mounting tabs

This lens nameplate is the replacement front-panel lens that restores the appearance and readable labeling on your appliance's control area. It provides a clean, finished look and protects underlying switches and displays from everyday wear. What it does

• Replaces a cracked, scratched, faded, or missing front-panel lens to restore readable labels and appearance
• Protects control buttons, switches, and the display area from dirt and wear
• Helps keep the control area looking new and prevents accidental pressing of internal components
• Fits into the existing bezel or mounting points for a direct cosmetic replacement

• One lens nameplate

• Disconnect power to the appliance before starting any repair
• Remove surrounding trim or bezel to access the lens; retain all fasteners
• Install the lens carefully to avoid scratching; align tabs or mounting holes and secure with original hardware
• If adhesive or clips were used originally, replace with manufacturer-specified fasteners

This bezel light is the interior trim piece that holds and protects the freezer compartment lamp, restoring a finished look and proper lamp fit. Use it when the existing bezel is cracked, warped, or missing. What it does:

• Secures the freezer lamp or lamp assembly in the compartment and keeps the bulb properly positioned
• Protects the bulb from contact with stored items and helps direct interior light
• Replaces cracked, broken, or discolored bezels that prevent the lamp from seating correctly
• Can resolve issues with a loose or rattling lamp housing

• Disconnect power to the appliance before accessing the interior lamp area to avoid shock
• Handle the bezel and nearby plastic components gently to avoid cracking during removal/installation
• Bulb removal or replacement may be required to install the bezel; use only approved replacement bulbs
• Refer to your refrigerator's service manual for model-specific disassembly and reassembly instructions