General Electric Knob, Dial & Button

The thermostat knob on my dryer broke and I couldn't find it in any of the stores in my area. I looked online and it was very expensive. I found your website when I went to Lowes. The gave me a card with your site. The knob was very reasonable, came within a week and I was able to put it on in a second! It was a very rewarding experience. Read more

I pulled off the retaining clip with pliers then removed the old knob and timer dial. I replaced all the parts with the new ones and used pliers to reinstall the clip. The teeth on the new knob engage to select the cycle. https://www.youtube.com/watch?v=cQwLtRcHx9k Read more

• Doesn't shut off
• Won't start

Found the part through appliancepartspros.com The part was the cheapest of several web sites. although shipping for such a small part was steep ($7.95 If I was purchasing bigger parts or heavier parts..the flat rate cost would be a bargain. The part arrived the next day and fit perfectly. In additon; obviously the original manufactured part was not holding up well as the new part had a metal reinforcement band that will prevent the cracking in the future. Read more

I actually called a repair service in our area. The serviceman asked questions and detected that I didn't need a timer unit but thought it was just a knob that was required. He offered to come out but the expense would be considerable. I am SO relieved that it was indeed the knob, and the dryer was fixed. In this time in our lives, every penny counts. I must applaud the serviceman for his honesty and dedication to his trade. He directed me to this website, but also added if there were any... Read more

Replaced rear bearing, upper and lower felts, drive belt. Have repaired dryer before for same problem years ago, knew what to do, on line diagrams helped to move memory. Cleaned all accumulated lint out of machine.Belt was changed only out of age.Looked good but thought to be on safe side. Read more

I first received the quality parts in less than 2 days. It took me 5 minutes to change out the timer and 2 of the minutes were finding where my fiancée put the Phillips head screwdriver. Unplug dryer first, remove top three screws from back panel. Pull old timer up and out, have new timer in hand and transfer one wire at a time. Once all wires are transferred, snap the new timer in its place. Replace your three screws, put knob on timer. Plug in dryer and test. Once completed, cleanup your... Read more

Live chatted with AppliancePartsPros to verify the correct replacement part. Ordered on line and received the knob the following day! So easy and saved $15. Read more

Went to the AppliancePart Pros website, found the OEM replacement parts and at a price that was better than any of the other sites I had looked into. Ordered the parts and they arrived within 2 days. Excellent service. Read more

I pulled off the retaining clip with pliers then removed the old knob and timer dial. I replaced all the parts with the new ones and used pliers to reinstall the clip. The teeth on the new knob engage to select the cycle. https://www.youtube.com/watch?v=cQwLtRcHx9k Read more

Remove and replace Read more

So, after looking for replacement parts, I found these. I was delighted. My original knobs were plastic with a silver finish. They had blistered from the heat of the stove over the years. The replacement knobs were all metal. Price was right. Very happy. Read more

Easily replaced the knobs Read more

Replaced two drawers, one shelf front, and the grille base Read more

I ordered a new knob and it arrived very quickly. The repair was simple and I will use appliance parts pros again should I need to. Thank you. Read more

Amazing story of speed & quality! Ordered on Friday 4pm, had parts in hand on 2pm on Sat, finished repair by 4pm ... 24hrs! The repair video was 100% on target. Replaced the rear drum bearing, front slides/glides, and the belt (cheap insurance!). All parts were exactly as described on APP.com. I (and my wife) couldn't be happier with the repair, and the exceptional service of APP! Do not be timid about trying this repair yourself. Take your time and watch the video. Priceless! Recommend... Read more

• Won't start

All I had to do was remove 3, 1/4" screws from the back and take the front off. Two 5/16th screws hold the circuit board in place, remove them and press the button into the hole from the back. Replace the circuit board, slide the front back on and install the three 1/4" screws. Always unplug the washer first! Read more