General Electric Guard, Shield, Barrier Parts

The Rear Drum Bearing Sleeve is an OEM part for GE dryers. It is designed to support the rear of the dryer drum, ensuring smooth rotation during the drying cycle. This sleeve reduces friction between the drum and the bearing, contributing to efficient and quiet operation of the dryer. This is the dryer rear drum bearing sleeve only. For the rear drum bearing kit order WE25M40.

You should replace the rear drum bearing sleeve if it becomes worn out or damaged. Causes of a bad bearing sleeve can include regular wear and tear, lack of lubrication, or excessive loads that cause undue stress on the component. A malfunctioning bearing sleeve can lead to increased friction, noise, and potential damage to other parts of the dryer.

Symptoms of a bad rear drum bearing sleeve include:

• Squeaking, grinding, or rumbling noises during the drying cycle
• The dryer drum not rotating smoothly or being off-balance
• Increased drying times due to inefficient drum movement
• Visible wear or damage to the sleeve

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Glass Light Lens is an OEM part for GE microwaves. It covers the light bulb inside the microwave, protecting it from food splatters and ensuring even illumination.The lenses measure approximately 7" x 3".

Causes of a bad glass light lens can include accidental impact, exposure to high heat, or general wear and tear.

Symptoms of a bad glass light lens include:

• Cracks or breaks in the glass
• Diminished visibility inside the microwave
• Light not being properly diffused
• Potential exposure of the light bulb to food splatters

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Stirrer Fan Cover is an OEM replacement part for GE Microwaves. It is responsible for shielding internal mechanisms during operation. 

Causes of a faulty cover include normal wear over time, cracking, or warping due to exposure to high heat. 

Symptoms of a problematic cover include:

• Excessive noise or vibration during use
• Reduced or uneven heating performance
• Gaps exposing vulnerable electrical components
• Loose pieces that could fall into the microwave cavity

This GE replacement part is also compatible with Hotpoint, RCA, and select Kenmore models.

The Canopy Mica is an OEM part for GE microwaves. This part covers the waveguide channel, preventing food particles and grease from entering the microwave's internal mechanisms.  

Causes of a bad canopy mica can include exposure to high levels of moisture or grease, physical damage such as cracks or burns, and general wear and tear over time.  

Symptoms of a bad canopy mica include:

• Sparks or arcing during microwave operation
• Burn marks or discoloration on the mica sheet
• Unusual noises while the microwave is running
• Uneven cooking or heating of food

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Microwave Oven Light Lens Cover is an OEM replacement part for GE microwaves. It serves as the protective glass shielding the internal light fixture. Reliable lens safety and clarity are pivotal to effortless visibility within microwave cavities.

Causes of a damaged light lens cover can include cracks or breaks from impact accidents during cleaning, warping from excessive heat exposure over time, or scratches obscuring transparency.

Symptoms of a compromised lens cover include:

• Cloudiness or opacity inhibiting light diffusion
• Exposure of live electrical wiring beneath broken glass
• Gaps permitting liquid/debris ingress into delicate internals
• Inability to accurately monitor microwaved items cooking

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is the clear glass lens that covers the cooktop light on select GE over-the-range units. It shields the bulb from grease and splatters while allowing bright, even illumination of the cooking surface below.

• Protects the cooktop light bulb from grease, moisture, and debris
• Restores proper lighting if the original lens is missing, cracked, or stained
• Helps maintain safe, even illumination of the range area
• Common symptoms: broken or missing lens, dim or uneven light due to a damaged cover

• Disconnect power to the appliance before servicing
• Allow bulbs and surrounding area to cool completely
• Handle glass carefully to avoid chipping; wear cut-resistant gloves
• Ensure the lens seats fully and any retaining tabs/screws are secured per the product's service instructions

This molded resin cover is a protective plastic shield used inside the microwave. It helps protect internal components and ducting from splatter and debris and restores a secure, finished fit when the original cover is cracked or missing. What it does:

• Shields internal components from grease, steam, and food splatter inside the unit
• Helps maintain proper airflow paths and a snug, rattle-free fit
• Common replacement when the original cover is cracked, warped, loose, or missing
• Visual cue: exposed internal parts or a cover that won't stay secured

• One resin (plastic) cover

• Disconnect power (unplug or switch off the breaker) and allow the unit to cool
• Access the cover location; remove retaining screws/clips and keep hardware for reuse
• Align the new cover and secure it without overtightening
• Ensure the cover is fully seated and not contacting nearby moving parts before restoring power

This glass light cover shields and diffuses the cooktop light, protecting the bulb from heat, grease, and splatter while maintaining clear, even illumination over your cooking surface.

• Covers and protects the cooktop light bulb
• Diffuses light for more even illumination and reduced glare
• Helps keep grease and debris out of the light cavity
• Replace if cracked, missing, discolored, or not staying secured

• Disconnect power to the appliance before servicing and allow the area to cool
• Support the cover while removing any retaining screw(s) or release tabs
• Reuse original hardware/clips as applicable and seat the cover fully
• Restore power and test the light for proper operation

This factory glass panel replaces a cracked, shattered, or missing original, restoring a clean, safe cover/viewing surface on your appliance. It helps protect internal areas from splatter and keeps the assembly looking and fitting the way it should.

• Replaces a damaged glass component within the original assembly on applicable models
• Restores a clear, smooth surface for proper appearance and function
• Helps shield underlying parts from spills, grease, and debris
• Common symptoms: cracked or shattered glass, missing piece, sharp edges, looseness/rattling

• Disconnect power before servicing; allow all surfaces to cool
• Wear cut-resistant gloves and eye protection; handle edges carefully
• Support the panel/door during removal and installation to prevent stress on frames/hinges

This vinyl sleeve fits over a rod, tube, or wire in the refrigerator to protect and cushion contact points. It reduces wear and vibration and helps keep components aligned for smooth, reliable operation.

• Provides a protective barrier at contact points to prevent abrasion or marring
• Helps maintain spacing and alignment for a snug, proper fit
• Cushions to damp vibration and reduce rattles or squeaks
• Replace if the sleeve is missing, cracked, hardened, or if components feel loose or make noise

• Disconnect power; turn off the water supply if working near water lines
• Note the sleeve's original location and orientation; take a photo for reference
• Remove the old sleeve and any debris; slide the new sleeve into the same position
• Check clearance and resecure related parts before restoring power

This resin canopy is the interior ceiling cover inside the microwave cavity. It shields the stirrer area from grease and splatter to help maintain even heating and protect internal components for safer, more reliable cooking. What it does:

• Covers and protects the stirrer/waveguide opening at the top of the cavity
• Helps promote even microwave energy distribution for consistent cooking
• Shields internal parts from grease, steam, and food debris
• Replace if warped, cracked, burned, discolored, loose, or if you notice arcing/sparking inside the cavity

• 1 resin canopy

• Disconnect power before servicing; microwave components can carry high voltage
• Remove the old canopy by releasing tabs or fasteners from inside the cavity
• Clean the cavity roof and seating surfaces before installation
• Ensure the canopy is fully seated and do not operate the microwave without it installed

This guard terminal protects and shields wire connection points on your appliance, helping prevent accidental contact and shorting while keeping terminals organized for reliable operation. What it does:

• Covers and insulates exposed terminal connections to reduce risk of arcing or short circuits
• Keeps wiring routed and separated for consistent electrical contact
• Helps avoid accidental contact during maintenance or part replacement
• Supports safe operation by protecting fragile terminal ends from bending or snagging

• Disconnect power to the appliance before inspecting or replacing electrical parts
• Replace only with the correct terminal guard
• Use basic hand tools; avoid bending terminals or over-tightening fasteners

This lower heat shield is a stamped metal shield that protects the oven's lower cabinet area and surrounding components from excessive heat. It helps maintain safe operation and reduces heat transfer to nearby parts. What it does:

• Shields the oven's lower cavity and insulation from direct heat
• Prevents heat-related damage to the range cabinet and nearby components
• Can reduce hotspots that cause smoking or burning odors
• Restores proper airflow and clearance under the oven when damaged or missing

• One lower heat shield

• Disconnect power (and gas, if applicable) before servicing the appliance
• Remove oven drawer and access panels to reach and replace the shield
• Use gloves to protect hands from sharp metal edges during installation
• Tighten fasteners securely but do not overtighten—replace any damaged mounting hardware

This shield cover protects internal appliance components from heat, debris and incidental contact, helping maintain safe operation and prevent damage. It fits into the appliance as a non-electrical protective guard. What it does

• Shields wiring, sensors and nearby components from heat and falling debris
• Helps prevent accidental contact with moving parts or hot surfaces
• Preserves component alignment by covering and supporting nearby assemblies
• Reduces the chance of shorting from loose objects or lint

• One shield cover

• Disconnect power (unplug appliance or shut off circuit) before servicing
• Use basic hand tools; avoid forcing fasteners to prevent damage
• Watch for sharp edges and wear gloves as needed
• Confirm exact fit against your model's parts diagram before final assembly

This cover-damper is the replacement plastic cover that fits over the refrigerator air damper to help direct cold air between compartments for more consistent cooling. Replaces a cracked, broken or missing damper cover. What it does:

• Protects the damper assembly and helps channel airflow from the evaporator to the fresh-food and freezer compartments
• Restores proper air direction when a broken cover causes uneven temperatures or poor cooling
• Works with the damper to reduce drafts and improve compartment temperature balance
• Simple, passive part that mounts to the damper housing

• One cover-damper

• Disconnect power to the appliance before starting any repair
• Remove interior panels or shelves as needed to access the damper housing; handle plastic clips gently to avoid breakage
• Verify fit and orientation against the existing part before finalizing installation
• If the damper motor or actuator is damaged or the issue persists after installing this cover, inspect the full damper assembly

This left switch breakwater is a small plastic retainer that holds the console switch assembly in place, keeping switches secure and aligned for reliable control operation. It helps restore proper switch positioning after damage or wear. What it does:

• Secures the left console switch assembly so buttons and selectors operate correctly
• Keeps the switch contacts aligned to prevent intermittent or non-responsive controls
• Helps block debris from interfering with the switch mechanism
• Commonly replaced when the switch feels loose, sticks, or the control behaves inconsistently

• One left switch breakwater

• Disconnect power to the appliance before beginning any repair
• Access typically requires removing the control console or panel; follow your model's service instructions
• Handle plastic retainers carefully to avoid cracking; replace if damaged