General Electric Spring Parts

• Ice maker not making ice
• Ice maker won't dispense ice
• Leaking

Much easier than expected, I was certain it had to be a water line but the solved everything Read more

• Door latch failure
• Ice maker not making ice
• Not dispensing water
• Ice maker won't dispense ice

My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser... Read more

I order both the paddle and spring and watched a video on how to remove the operating panel to replace them Read more

First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then... Read more

I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more

I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more

I replaced all 4 suspension rods and springs and now it spins very smooth. They weren't broken, just badly worn. It gave new life to my 15 year old GE Profile washer. They are basically springs, so they wear after a while. It was well worth the hour I spent fixing it. You need a good long reach to get to the back 2 and you have to take off the dampening straps and the control panel so you can gain access. All in all, I'm happy with the repair, although I though that these parts are bit... Read more

I replaced the lever asm. and spring Read more

First off OUTSTANDING experience with AppliancePartsPros.com! Ordered my parts on Tuesday and they arrived Wed morning!! Replaced interlock switch plunger and spring, which was obviously broken compared to the new one. This solved the problem of my door not latching but the machine would still not turn on. So with two interlock switches on the door, one had to be bad. So decided to start by replacing one switch at a time until I found the bad one. If both were bad I would just buy a... Read more

1) Remove toe kick panel - 2 Philips head screws 2) Lay down on floor. This might be the hardest part of the repair from some people! 3) Remove broken spring, no tool required. 4) Using your fingers, slip one end of new spring into hole on lever arm. (If you're not sure how it should go, look at the spring on the other door, assuming you have a side-by-side.) 5) Hook the other end of the spring around a round-shank screwdriver. (Don't even bother with pliers. You will disregard this advice... Read more

When I took it apart I found that the drive cup was cracked, the helix lock plate hole was reamed out and the ice deflector spring was broken. The biggest problem was the helix had slipped down the shaft and allowed the end of the shaft to bore a hole in the housing which made it a bear to get out. Others have had the same problem. Once I got past that obstacle, it was simple to replace all the parts and it's working like normal again. Very helpful video explaining the repair. Read more

I shopped around a bit - found one retailer that only had 1 shock in stock, another that only stocked the front shocks, etc. There is definitely a difference in the springs between the green colored and white colored shocks! I've torn this washer down before, so I'm fairly familiar with how it's put together. I've seen some of the You-tube videos on replacing this item, and some of the videos show far more disassembly than is required. I only removed the front, top, and controls, and... Read more

I literally could have done this job with a blindfold on! No kidding. Come on people! My grandmother could have done this one! Since the rubber gasket/skirt in the front of the washer (seals the door) was twisted when the spring failed and the drum failed, I had to remove the wire hoop and spring that held it in place and readjust the skirt. Easy. Them I removed the top of the washer (6 screws). Easy. Immediately you could see the failed spring. I ordered 2 springs so I could replace both... Read more

Downloaded the Technical Service Guide and followed the instructions for removal of the Door Closure Mechanism. Items the instructions failed to mention: 1. Although they took the trouble to call for removal of a 3/16" Allen head bolt, they referred to the closure mounting bolts as just "bolts". In fact, they were T-25 bolts. If I didn't have a Torx kit, it would have required a trip to the Orange Big Box Home Center to complete the job. 2. Although the instructions don't describe this step,... Read more

Got a small piece of sheet metal for Home Depot, Cut it to fit, and drilled holes to fit. Replaced spring and plastic holder, and put it back together. Spring was a little tricky to put on, because of the spring strength, but I got it. Read more