General Electric Wall Oven Parts

Right-side refrigerator door hinge that supports and pivots the door for proper alignment and smooth operation. Replaces a worn or damaged hinge to help restore even closing and reduce door sag or binding. What it does:

• Provides the pivot point that supports and aligns the right-side door for proper sealing.
• Restores even door movement and helps eliminate sagging or drooping that prevents the door from latching.
• Helps stop binding, sticking, or noisy hinge action that can occur with worn pivot points.
• Works with the door mounting points to maintain correct gap and compression for the gasket.

• Disconnect power or unplug the appliance before servicing to avoid electrical hazards.
• Support or remove the door before removing the hinge; doors can be heavy and may contain glass shelves—use a second person if needed.
• Use appropriate hand tools and retain any original screws/fasteners.

This oven door latch assembly secures the door and communicates lock status to the control. Replacing a worn or jammed latch restores safe door locking so bake and self-clean cycles can start and finish correctly.

• Locks and unlocks the oven door when engaged or commanded by the control
• Secures the door during the self-clean cycle for safety
• Helps resolve issues such as a door that won't lock or unlock, self-clean that won't start/finish, or a persistent "door locked" indicator
• Wear, binding, or internal failure can prevent proper latching

• Disconnect power at the breaker before servicing
• Access location varies by model; typically serviced from the top, rear, or control/console area—follow your model's service procedures
• Transfer any mounting hardware and reconnect wire harnesses one at a time
• After installation, verify smooth latch movement and door locking before running a cycle

This replacement oven door gasket forms the heat-resistant perimeter seal around the door opening. Restores a tight seal to retain heat, support accurate temperatures, and reduce warm-air leakage for better baking performance.

• Creates the compressible seal between the oven cavity and door to keep heat in
• Helps the oven preheat efficiently and maintain even temperatures
• Reduces warm air and odors escaping around the door edge
• Common failure signs include fraying, flattening, gaps, longer preheat, or uneven baking

• Disconnect power and allow the oven to cool completely; wear gloves
• Open the door and remove the old gasket from its retainers/channels, noting clip locations and orientation
• Clean the groove/retainer; starting at the top center, press the new gasket in evenly without stretching and seat corners fully
• Close the door and check for uniform contact around the perimeter

This capillary clip secures the oven thermostat's sensing bulb/capillary to the cavity wall so it stays correctly positioned for accurate temperature control. Replace a missing or damaged clip to prevent a sagging bulb and erratic oven performance.

• Holds the thermostat capillary tube/sensing bulb in place inside the oven
• Helps maintain consistent temperature regulation by keeping the bulb properly located
• Direct replacement for a broken, corroded, or missing clip
• Symptoms include a loose or dangling bulb, uneven baking, or temperature swings

• Disconnect power (and gas, if applicable) and allow the oven to cool completely
• Access the oven cavity; locate the thermostat sensing bulb and capillary along the wall or back panel
• Position the bulb/capillary and secure with the new clip; avoid kinking or crushing the tube
• Restore power, and test operation

This oven door gasket creates a heat-tight seal between the oven door and frame to help retain heat and improve cooking consistency. Replacing a worn gasket reduces heat loss and limits smoke or steam escaping during use. What it does:

• Seals the oven door to help maintain internal temperatures and consistent cooking results.
• Reduces heat and steam leakage that can cause longer cook times or uneven baking.
• Typical signs you need it: visible gaps, flattened or torn seal, or heat/steam escaping from the door.
• Matches OEM fitting style for a direct replace of the damaged or degraded seal.

• Disconnect power to the oven and allow it to cool completely before starting.
• Access the gasket per the manufacturer's guidance—some doors may need to be opened or removed for easier access.
• Remove the old gasket from the channel, then press the new gasket evenly into the channel so it seats fully around the door perimeter.
• Reuse original retainers or hardware; if adhesive or clips are required, follow the oven maker's instructions.

Replacement thermostat that senses and controls the appliance heating system to restore accurate heating and stable temperature cycles, helping the appliance reach and maintain the set temperature. What it does:

• Senses temperature and signals the heating element or valve to turn on/off to maintain set temperature.
• Commonly linked to symptoms such as failure to reach set temperature, temperature fluctuating or cycling erratically, or continuous heating.
• Works as the temperature-regulation component in the appliance's control pathway to stabilize performance.
• Matches the OEM function for temperature control; use when thermostat diagnostics indicate a failed or inaccurate sensor.

• Disconnect power to the appliance before attempting removal or installation to avoid shock or ignition hazards.
• Handle the sensing element and terminals carefully to avoid damage; ensure secure electrical connections and proper routing of any capillary or sensor lead.
• After installation, test the appliance through a full heat cycle to confirm correct operation.

This control valve is an important safety feature found on many gas ranges. It's located inside the back of the range near the area where the buttons and controls are found. The reason the control valve is included in ovens is to prevent gas from moving to the burners if the igniter is not able to ignite the gas or there is no electricity. The control valve could be faulty if there is a smell of gas near the valve, the burner flame flickers, or the flame cannot be turned on high.In any of these situations, the control valve must be replaced. The repair is easy and takes only a few minutes. The bottom of the oven will need to be removed, which may require a screwdriver. After removing it, remove the flame spreader by taking out two screws and sliding it out of the oven. Remove the screw holding the oven burner tube and take it out to access the valve and replace it.This control valve is made to be compatible with RCA, Kenmore, Roper, General Electric, and Hotpoint ranges. It's sold as an individual OEM replacement part that is sourced directly from the manufacturer.

This SPDT high-amp switch controls high-current circuits by switching one input between two outputs, restoring proper electrical control in affected appliance functions. Built for high-load switching where reliable on/off selection is required. What it does:

• Directs high-current power from a single input to one of two outputs (single-pole, double-throw action)
• Replaces worn or failed selector/limit-style switches that cause intermittent or no power to a circuit
• Commonly used where a high-amp, durable switching contact is required to complete a function
• Helps stop symptoms like intermittent operation, failure to switch between states, or no power to the controlled circuit

• One SPDT high-amp switch (WB24T10160)

• Disconnect power to the appliance before inspecting or replacing the switch
• Verify wiring locations and take a photo before removal for correct reconnection
• Use proper tools and avoid touching energized contacts;

This oven control assembly is the electronic control board that manages oven functions, display and user inputs so your range can set and maintain cooking modes and temperatures. It restores control and display functionality when the original board fails. What it does:

• Receives commands from the touchpad/knobs and controls bake, broil, timers and oven lights
• Drives the front display and clock so settings and temperatures are shown correctly
• Sends signals to relays and safety circuits to energize heating elements and modes
• Common symptom fixes: blank or erratic display, unresponsive controls, oven not starting or failing to maintain temperature

• One oven control assembly (electronic control board)

• Disconnect power at the breaker before testing or installing to avoid shock or damage
• Handle the board carefully to avoid ESD or physical damage; do not touch exposed circuitry

Upper window pack assembly that replaces a cracked or damaged refrigerator door window panel, restoring appearance and helping protect the components behind the outer window. What it does:

• Replaces the upper door window pack to restore a clear, finished exterior on the appliance door.
• Addresses visible damage symptoms such as cracked, scratched, cloudy or broken window panels.
• Protects internal door components from exposure to moisture and debris.
• Matches the OEM-style mounting points for a like-for-like replacement when used with the correct model parts.

• Disconnect power and remove food from the door area before starting any repair.
• Handle the window pack carefully; wear cut-resistant gloves and eye protection when removing broken or cracked pieces.
• Remove any trim or fasteners per the appliance's service instructions; retain mounting screws and gaskets as needed.
• Refer to the OEM service manual or diagram for model-specific removal and reassembly steps.

This inner oven door glass is a replacement inner-pane that restores visibility and helps contain heat inside the oven cavity. It fits into the oven door assembly and replaces damaged or cracked inner glass for safe, functional use. What it does:

• Replaces cracked, broken or fogged inner oven door glass to restore clear viewing of the cooking chamber
• Helps maintain proper heat containment when installed correctly
• Works with the oven door assembly to preserve insulation and door integrity
• Reduces heat transfer to the outer door surface when used as part of a complete door repair

• Allow the appliance to cool and disconnect power before starting any repair
• Handle glass carefully; wear cut-resistant gloves and eye protection
• Installation typically requires removing the oven door and disassembling the door panels.

Package of 12

This hex-washer-head screw secures appliance components and panels. The correct 10-16 thread, 1-inch length fastener restores a tight, factory fit when an original screw is missing, stripped, or corroded.

• Fastens brackets, shields, trim, or panels to the appliance chassis
• Helps resolve rattling, gaps, or loose parts caused by a missing/damaged screw
• 10-16 thread with 1-inch length matches factory hardware for specified locations
• Hex-washer head provides solid tool engagement and distributes load to protect surfaces

• Disconnect power before servicing; if working on a gas appliance, also shut off the gas supply
• Support the part being secured and align holes before tightening
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Replace any additional missing screws in the same area for uniform support

This seal for the front frame creates a tight barrier between the oven door and frame to help retain heat and reduce smoke or odor escape. It restores a proper door seal to improve cooking performance and safety. What it does:

• Replaces worn, torn, or deformed front-frame gasket that allows heat or smoke to leak from the oven cavity
• Helps maintain consistent oven temperatures for more even cooking and baking
• Reduces heat transfer to surrounding cabinetry and surface areas
• Stops drafts, burning odors, or visible gaps around the door edge

• One seal for the front frame

• Disconnect power and let the appliance fully cool before attempting service
• Inspect orientation and seating before final installation; some models require door removal for access
• Use proper tools and gloves to avoid cuts; ensure seal is fully seated and continuous around the frame

This bake burner is the oven's main gas tube that produces steady heat for baking and roasting, restoring proper cooking temperatures and more consistent bake results. It fits gas ovens that use a separate bake tube assembly. What it does

• Directs and distributes the oven's gas flame to generate baking heat
• Restores proper oven temperature when the bake flame is weak or absent
• Helps eliminate uneven baking or undercooked dishes caused by a failing tube
• Works with the oven igniter and gas valve to light the burner safely

• One bake burner (bake tube) as shown

• Turn off gas supply and electrical power before starting work
• Removal may require disconnecting burner mounting screws and any brackets; keep track of fasteners
• Inspect and replace related parts (igniter, orifice) if ignition problems persist

This temperature-control thermostat regulates refrigerator cooling cycles to help maintain set temperatures and proper food storage. It senses cabinet temperature and signals the compressor and fans to run as needed for stable cooling. What it does:

• Monitors interior temperature and switches compressor/fan circuits on or off to maintain the selected setting
• Restores normal cooling when a failed thermostat causes the fridge to run constantly or not run at all
• Helps prevent temperature swings that can lead to spoiled food or excessive frost
• Common symptoms: refrigerator too warm, fridge runs nonstop, or unit doesn't respond to temperature adjustments

• Disconnect power to the appliance before beginning any work to avoid shock or injury
• Access may require removing the control housing or panel; keep track of screws and fasteners
• Disconnect the wiring connector gently; avoid bending or stress on wires and the sensor capillary
• After installation, restore power and verify proper cycling and temperature control