General Electric Wall Oven Parts

Fixes oven door that won't latch or stay closed. This latch and harness assembly secures the door and sends the closure signal to the control board.

Controls gas pressure for safe burner operation. Mounts at gas supply line. Replace if flame height is too low, inconsistent, or after fuel conversion.

Oven won't stop heating or temperature keeps rising? This thermostat regulates oven temperature cycles. Moderate difficulty repair with basic tools.

Replacement thermostat that senses and controls the appliance heating system to restore accurate heating and stable temperature cycles, helping the appliance reach and maintain the set temperature. What it does:

• Senses temperature and signals the heating element or valve to turn on/off to maintain set temperature.
• Commonly linked to symptoms such as failure to reach set temperature, temperature fluctuating or cycling erratically, or continuous heating.
• Works as the temperature-regulation component in the appliance's control pathway to stabilize performance.
• Matches the OEM function for temperature control; use when thermostat diagnostics indicate a failed or inaccurate sensor.

• Disconnect power to the appliance before attempting removal or installation to avoid shock or ignition hazards.
• Handle the sensing element and terminals carefully to avoid damage; ensure secure electrical connections and proper routing of any capillary or sensor lead.
• After installation, test the appliance through a full heat cycle to confirm correct operation.

Replacement control panel faceplate for wall ovens. Covers and protects the control board area. Replace if cracked, dented, faded, or missing.

Fix an unresponsive oven control panel or blank display with this control display module. Shows settings, temperature, and accepts commands. DIY repair.

Replacement refrigerator door gasket that restores a tight seal to help maintain proper cooling and reduce frost and moisture buildup. Fits the door channel to stop warm-air leaks and improve overall temperature stability. What it does:

• Seals the refrigerator door perimeter to keep cold air in and warm air out.
• Helps reduce frost and ice buildup inside the compartment.
• Can reduce condensation and uneven cooling caused by a worn or damaged seal.
• Common symptoms of a failing gasket: warm spots, excess frost, visible gaps around the door, or higher-than-normal energy use.

• Unplug the appliance and remove food from the door area before beginning work.
• Clean and dry the gasket channel and door surface; align the gasket and press it fully into the channel for an even seal.
• If the gasket is stiff, gently warming it can make installation easier—avoid excessive heat.
• Confirm this part number matches your appliance model before installing.

Small rubber bumper that cushions contact between oven door and cabinet. Replace if cracked, missing, or worn to reduce noise and protect finishes.

Rubber door bumper cushions and stabilizes your oven door. Replaces worn, cracked, or missing bumpers that cause rattling or uneven door closure.

This flat washer (.250 inch inner diameter x .812 inch outer diameter) is a simple replacement part that helps distribute load from a fastener and protects mating surfaces for reliable appliance operation. What it does:

• Provides a stable bearing surface for screws, bolts or studs to reduce wear on parts
• Helps distribute clamping force to prevent pull-through or deformation of softer materials
• Reduces vibration and movement at the joint when installed correctly
• Missing or damaged washers can lead to loose fasteners, increased vibration or component misalignment

• Disconnect power and water before servicing the appliance
• Replace like-for-like: inner/outer diameters and thickness match the original washer
• Inspect mating hardware and surfaces for damage; replace corroded or deformed fasteners as needed
• Tighten fasteners evenly and avoid over-torquing to prevent washer or component damage

Black-finished screw secures oven panels, trim, and brackets. Replace missing or damaged fasteners to restore solid fit and prevent rattling or gaps.

Mounting bracket that secures the control console and circuit board to the oven frame. Replace if cracked, broken, or causing misalignment issues.

Oven door won't stay closed or locks unexpectedly? This door latch assembly secures your oven door for safe operation and proper temperature control.

This replacement crystal lamp provides the interior lighting for refrigerators, improving visibility so food and shelves are easier to see. Designed as a direct-fit replacement to restore a clear interior light. What it does:

• Illuminates the refrigerator interior to help you find items more easily.
• Replaces a cracked, broken, dim, or missing lamp assembly.
• Fits into the existing lamp housing and works with the original socket.

• Disconnect power to the appliance before starting any work to avoid electrical shock.
• Handle the lamp carefully—wear gloves or use a cloth to avoid cuts from glass.
• Remove old lamp assembly per the owner's manual; align and seat the new lamp securely in the housing.

Decorative lens cover for range control panel indicator lights. Replace when cracked, faded, or missing to restore appearance. Verify fit by model.

Seals and cushions your oven door to reduce vibration and rattling. Replace when worn to restore proper spacing and eliminate air leaks. Verify fit.