General Electric Washer Gasket & Seal

The Door Boot Seal is an OEM part for GE washing machines. This seal is positioned around the door opening of front-load washers, creating a watertight barrier that prevents water from leaking during wash cycles. It also helps to reduce noise and vibration, ensuring smooth and efficient operation.

Over time, the door boot seal can deteriorate due to constant exposure to water, detergent, and the high temperatures of washing cycles. If the seal becomes damaged, it can lead to leaks, mold growth, and decreased washing performance.

Symptoms of a bad door boot seal include:

• Water leaking from the front of the washer
• Mold or mildew buildup on the seal
• Unpleasant odors from the washer
• Visible tears, cracks, or warping of the seal

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

For the door boot to tub clamp order WH01X10277. For the door boot to front spring clamp order WH01X10279.

The Door Gasket is an OEM part for GE washing machines. Located around the washer door opening, it creates a tight seal during cycles to prevent water leaks.   

Symptoms of a bad door gasket include:

• Water leaks from the washer door opening  
• Excess moisture buildup or puddling near the door
• Inability to achieve proper seal for optimal washing

Causes for failure can be cracks, perforations, or deteriorated material from repeated use and mechanical stresses over time. Mineral or soap deposits may also degrade sealing properties.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a gasket made for use with washing machines. This particular gasket fits between the washer tub and the door, forming a seal that prevents leaks. Over time, gaskets are subject to wear and tear that can cause them to become brittle, rip, tear, warp, or otherwise be rendered ineffective. If the user notices that there is water leaking from the washing machine door during use, or the gasket is displaying visible signs of wear and tear, replace this part immediately. No tools are required to install this gasket.This gasket is manufactured from high-quality, durable, non-corrosive materials to ensure the best possible quality. This part is manufactured by General Electric and has been sourced directly from the manufacturer. It is sold individually and compatible with washers from General Electric, Hotpoint, and RCA.

This door gasket is the flexible sealing strip that mounts around a refrigerator door to keep cold air in and warm air out, helping maintain temperature and reduce energy use. It restores a tight door seal for proper cooling performance. What it does:

• Seals the door edge to prevent warm air infiltration and cold air loss
• Helps reduce frost buildup and prevents moisture leaks into the compartment
• Supports consistent internal temperature to protect food freshness
• Common symptoms of a failing gasket: visible gaps, torn or flattened seal, cold/temperature fluctuations, excess frost or condensation

• High-level: remove the old gasket, align and seat the new gasket into the channel around the door; some models use screws or retainers
• Safety-first: unplug the appliance or disconnect power before attempting removal/installation
• Handle carefully to avoid tearing; warm the gasket slightly to help fitment if needed
• Refer to your model's service manual or OEM instructions for model-specific steps and fastener locations

This door gasket replaces a worn or damaged refrigerator door seal to help restore a tight closure and improve cooling performance. It creates a consistent seal around the door edge to reduce air leaks and frost buildup. What it does:

• Seals the refrigerator/freezer door edge to keep cold air in and warm air out
• Helps prevent frost buildup and condensation inside the compartment
• Reduces compressor run time caused by air leaks around the door
• Often needed when the seal is torn, warped, compressed, or no longer magnets properly

• Disconnect power to the appliance before starting any service
• Remove the old gasket by loosening retaining screws or popping out mounting retainer
• Clean the mounting channel of debris and adhesive residue before installing the new gasket
• Align the new gasket around the door, secure the retainer if applicable, and press firmly to seat; warm the gasket with a hair dryer on low if needed to help it conform