General Electric Washer Dryer Combo Parts

Replacement rotary control knob for washer dryer combos. Restores manual control of temperature and function settings when original is cracked, worn, or missing.

Replacement dryer drum assembly for laundry centers. Restores the rotating drum that tumbles clothes. Order when your drum is cracked, warped, or damaged.

This internal-bias thermostat senses oven temperature and helps the control board maintain the set heat level. Replacing a failing thermostat restores more consistent temperature control and more reliable cooking results. What it does:

• Senses cavity temperature and signals the control to cycle the heating element or burner
• Regulates heating cycles so the oven reaches and holds the set temperature
• Common symptoms: oven takes too long to heat, temperature fluctuates or runs too hot, or the oven cycles on/off erratically

• Disconnect power (unplug or shut off circuit breaker) before servicing to avoid shock
• Access location varies by model—part is typically mounted near the control or inside the oven cavity housing
• Handle the sensor element and terminals carefully to avoid damage; reuse of mounting hardware depends on your model

Seals the unused drum light opening in your dryer cabinet. Replace if missing, cracked, or brittle to contain lint and protect internal components.

Secures the rear drum bearing to keep your dryer drum aligned and rotating smoothly. Replace if bracket is cracked, bent, or worn to restore proper support.

Seals the top of the outer tub to contain water and suds. Replace if cracked, broken, or worn to restore proper sealing and protect garments during wash.

Dryer won't advance through cycles or stops mid-cycle? This timer control board restores automatic cycle progression in your washer dryer combo unit.

This roller support holds the dryer drum roller in place to help the drum turn smoothly and stay aligned. Replacing a worn support can reduce noise and wobble and help protect the belt and drum from uneven wear. What it does:

• Holds and positions the drum roller so the drum rotates with minimal friction
• Keeps drum alignment and belt tracking stable during operation
• Helps prevent drum wobble and uneven wear that can lead to rubbing or thumping noises
• Common symptoms: loud squealing or grinding, thumping during rotation, visible drum wobble

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the dryer front or rear panel; follow the model's service manual
• Inspect the roller, axle, and adjacent support components; replace any worn parts to prevent repeat failure
• Use proper tools and secure fasteners to factory torque

Secures the drain boot or hose to the washer tub outlet to prevent leaks and separation. Replace if leaking or hose detaches. Confirm fit with model.

Front suspension rod assembly that supports and stabilizes the washer tub from the cabinet. Replace if worn, broken, or causing excessive vibration.

This rubber agitator cap seal creates a watertight barrier at the base of the washer agitator to help prevent leaks and keep the transmission area dry. It's a simple replacement that restores proper sealing around the agitator. What it does:

• Seals the agitator base to reduce water entering the transmission and cabinet area
• Helps prevent leaks that can cause rust, puddling, or damage under the washer
• Keeps contaminants and detergent residue out of the gearcase area
• Supports consistent wash performance by maintaining a dry drive assembly

• Disconnect power and turn off the water supply before starting any repair
• Remove the agitator cap and agitator per your model's service instructions to access the seal
• Inspect surrounding parts (agitator cap, agitator, and shaft) for wear and clean mating surfaces before installing the new seal

Replacement alignment pin for laundry center hinge or latch assemblies. Restores proper positioning of moving parts when original is broken, worn, or missing.

This is a replacement pointer for control panels and timer knobs that restores a clear, visible indicator of the selected setting. It helps you quickly see and select the correct cycle or temperature. What it does:

• Replaces a cracked, broken, faded, or missing pointer so the control position is visible
• Aligns with the control knob to show the active setting or timer position
• Improves usability when the original pointer is worn or detached
• Matches the original white/dark gray color for a clean appearance

• Always disconnect power (unplug the appliance or shut off the breaker) before servicing
• Remove the control knob as needed, then press the pointer into the control shaft or bezel until it seats
• Do not force the part; stop and verify the part number and control style
• Refer to the appliance owner's manual or a repair guide for model-specific removal steps

Door hinge for dryers. Attaches the door to the dryer cabinet frame, allowing it to open and close smoothly. Replace if cracked, broken, or worn.

Dryer won't heat or stops mid-cycle? This thermal limiter cuts power when temperatures exceed safe limits. Common DIY repair, takes 30-45 minutes.