General Electric Washer Dryer Combo Parts

The agitator screw secures the washer's agitator to the drive shaft so it can move clothes effectively during the wash cycle. Replace a lost, stripped, or rusted screw to help stop wobble and restore proper agitation.

• Fastens the agitator to the drive shaft/coupler to transfer motion
• Address a loose or wobbly agitator, rattling/clunking, or weak/intermittent agitation
• Replace if the original screw is missing, corroded, or has stripped threads or head
• Helps prevent the agitator from lifting off during operation

• Disconnect power and ensure the washer is empty before servicing
• Remove the fabric softener dispenser and agitator cap to access the fastener
• Align parts, start the screw by hand to avoid cross-threading, then tighten snugly—do not overtighten
• Reinstall caps/dispenser and run a brief test cycle to proper agitation

This suspension rod support socket replaces the plastic cup the suspension rod sits in on a top-load washer. Replacing a worn socket restores smoother tub movement and helps reduce vibration and noise during wash and spin cycles.

• Supports the suspension rod at the tub/frame connection point
• Provides a low-friction pivot to stabilize the basket
• Helps reduce excessive shaking and out-of-balance banging
• Common signs of failure: cracks, squeaks/scraping, or the rod popping out

• Unplug the washer and shut off water supply before servicing
• Access the suspension area per your model (remove top/front panel as needed)
• Support the tub, relieve tension on the suspension rod, swap the socket, and ensure the rod seats fully in the new socket
• Reassemble, level the washer, and run a test spin to check balance

This part is the outer tub assembly for washing machines. It is often used in washer dryer combo units. This particular part houses the spin basket. It also holds the water during the washing cycles. In the event that the washing machine is leaking water, do a visual inspection of the outer tub to check for any cracks. If the tub has been damaged in any way, it will allow water to leak out. If this is the case, it will need to be replaced with this durable part. Make sure to unplug the washing machine from the outlet prior to attempting to replace this part. Wear work gloves to protect the hands.The tub is compatible with washing machines and washer dryer combo units that are manufactured by GE and Kenmore. It is a genuine OEM part this is sourced directly from the manufacturer. It is sold individually.

This replacement drum assembly restores the rotating drum that holds and tumbles clothes in your dryer, helping return smooth operation and reduce rubbing or scraping noises. Designed as a direct-fit service part when matched to your model. What it does:

• Houses and supports clothes while rotating during dry cycles to enable tumbling and even drying.
• Provides a smooth, durable surface to prevent clothes from catching or rubbing against the cabinet.
• Maintains correct drum alignment so the belt and rollers run smoothly.
• Common symptoms indicating a worn drum: loud scraping or grinding, visible drum wobble, or clothes that don't tumble properly.

• Disconnect power (and gas for gas dryers) before beginning any service.
• Retain original mounting hardware; additional fasteners or seals may be required if not supplied.

This tub seal assembly keeps the washer's inner tub sealed around the drive shaft to help prevent water leaks and contain wash water. It replaces a worn or damaged tub seal to restore a watertight fit. What it does

• Seals the gap between the inner tub and the transmission/drive shaft to reduce leaks
• Helps prevent water from entering the transmission area and causing damage
• Commonly replaced when you notice water on the floor or pooling under the washer
• Used when the existing seal is cracked, torn, or excessively worn

• One tub seal assembly

• Disconnect power and shut off water before starting any repair
• Replacement typically requires partial disassembly of the washer (cabinet or front panel removal) and access to the tub/transmission area
• Inspect shaft and surrounding surfaces for wear or damage and clean mounting surfaces before installing the new seal

This dryer bearing bracket secures the drum's rear bearing to keep the drum aligned and rotating smoothly. Replacing a worn bracket can help reduce drum wobble, scraping noises, and uneven drum rotation. What it does:

• Supports and locates the rear drum bearing to maintain proper drum alignment.
• Helps prevent the drum from wobbling, rubbing, or scraping against the cabinet.
• Can reduce or eliminate grinding, squealing, or thumping noises caused by a loose or damaged rear support.
• Works with the dryer's rear bearing assembly to enable consistent drum rotation.

• Disconnect electrical power (and gas, if applicable) before beginning any repair.
• Access typically requires removing the dryer drum and rear bulkhead.
• Inspect the bearing, shaft, and surrounding glides; replace any worn components to prevent repeat failure.

This light hole plug seals the unused drum-light opening in the dryer cabinet. Replacing a missing or brittle plug helps contain lint, limit drafts, and protect internal components around the opening.

• Covers the factory light opening when no drum light is installed
• Helps maintain proper cabinet airflow and lint containment
• Shields the opening from dust and moisture
• Replace if the plug is missing, cracked, hardened, or won't stay seated

• Disconnect power before servicing
• Access the light-hole location per your model's service instructions
• Press the plug fully into the hole until seated flush
• Ensure no wires or components are pinched around the opening

This pulley nut secures the washing machine's drive pulley to its shaft, helping keep the belt aligned so the basket can agitate and spin smoothly. Replacing a worn or missing nut helps prevent pulley wobble and belt issues. What it does:

• Fastens the drive pulley securely to the shaft
• Helps maintain proper belt tracking and drive engagement
• A loose, stripped, or missing nut may cause rattling or scraping noises, belt slippage or the belt coming off, and intermittent or no spin/agitation

• One pulley nut

• Disconnect power and water; wear appropriate PPE
• Access the drive pulley from the rear or bottom per the service instructions
• Support the pulley while loosening/tightening the nut to avoid stressing the shaft
• Pulley seating and belt alignment before reassembly and test run

This rubber agitator cap seal creates a watertight barrier at the base of the washer agitator to help prevent leaks and keep the transmission area dry. It's a simple replacement that restores proper sealing around the agitator. What it does:

• Seals the agitator base to reduce water entering the transmission and cabinet area
• Helps prevent leaks that can cause rust, puddling, or damage under the washer
• Keeps contaminants and detergent residue out of the gearcase area
• Supports consistent wash performance by maintaining a dry drive assembly

• Disconnect power and turn off the water supply before starting any repair
• Remove the agitator cap and agitator per your model's service instructions to access the seal
• Inspect surrounding parts (agitator cap, agitator, and shaft) for wear and clean mating surfaces before installing the new seal