General Electric Washer Dryer Combo Parts

Door switch lever for dryers. Activates the door switch mechanism when the door closes. Replace if cracked, broken, or missing to restore proper door operation.

Replacement leveling foot for washer dryer combos. Adjusts appliance height to eliminate rocking on uneven floors. Order a new foot if original is cracked or missing.

This ring drain hose is the replacement drain tube that routes and removes water from the appliance, restoring proper drainage and preventing leaks or standing water in the wash area. Designed to match the original fit and function. What it does:

• Channels wastewater from the tub/pump to the household drain to maintain normal drain cycles
• Restores proper drainage when the original hose is cracked, kinked, or leaking
• Helps prevent leaks and water damage caused by failed or deteriorated hoses
• Compatible with compatible stock mounting points for a like-for-like replacement

• One ring drain hose (1 piece) as pictured

• Disconnect power and water supply before servicing to avoid shock or flooding
• Inspect adjoining clamps and fittings; replace clamps if corroded or damaged for a secure seal
• Ensure hose routing is free of sharp bends or kinks and is secured per the appliance's service instructions

Secures the capacitor in your laundry center. Replace if clip is broken, cracked, or capacitor becomes loose. Verify fit with your model number.

Small drain fitting that routes overflow water away from your laundry center. Replace if cracked, broken, or leaking to prevent water damage and spills.

Secures the drain pump hose connection on your washer. Replace if you notice leaks around the pump or loose hose fittings. Verify fit with your model.

This oven door gasket provides a replacement seal that helps keep heat and cooking odors inside the oven for consistent cooking and improved efficiency. It restores a tight seal where the door meets the oven cavity. What it does:

• Replaces a worn, torn, or brittle door gasket to reduce heat loss and hot spots
• Helps the oven reach and maintain set temperatures more consistently
• Minimizes smoke, burning smells, and excess energy use caused by leaks
• Improves cooking performance by restoring a proper seal around the door

• One oven door gasket

• Disconnect power to the range/oven before beginning any repair
• Allow the oven to cool completely; remove the oven door per the manufacturer's instructions if required
• Gasket typically attaches by pushing into a channel around the door or oven frame; use a non-marring tool if needed
• Follow OEM instructions for reinstallation and torque recommendations

Washer tub gasket seals the outer tub to prevent leaks. Replace if you notice water pooling under your washer. Confirm fit with your model number.

Control panel mounting bracket for washer dryer combos. Secures the control panel assembly in place. Replace if cracked, bent, or broken hardware.

Mounting bracket that secures the pressure switch in your washer dryer combo. Replace if bracket is cracked, bent, or broken causing switch misalignment.

Front upper brace for laundry center units. Secures and supports the front panel assembly. Replace if cracked, bent, or broken to restore stability.

This harness selector is the wire connector assembly that routes power and signals between the selector switch and oven/range control components, restoring reliable connections and control function. What it does:

• Connects the selector/control switch to burners, igniters, or control modules so selections register properly
• Replaces worn or damaged wires and terminals that can cause intermittent control response
• Helps address symptoms like selector positions not responding, intermittent heating, or controls that fail to change settings
• Maintains factory routing and connector fit for a correct electrical connection

• Disconnect power to the appliance before servicing to avoid shock or damage
• Inspect connectors and wire insulation for damage; match connector shapes and pin counts before installing
• Seat all terminal connectors fully and secure any routing clips or retainers

Replace your washer's siphon break cap if it's cracked, broken, or missing. This protective cover installs on the siphon break assembly to prevent leaks.

Secures the motor assembly in your washer. Replace this retainer if it's cracked, broken, or missing to properly mount and stabilize the motor housing.

Protective screw sleeve guard for washer dryer combo units. Replace if cracked, broken, or missing to protect screw threads and housing components.