General Electric Washer Parts

Siphon pipe for washer drain air-break assembly. Prevents backflow and unintended siphoning. Replace if cracked, broken, or missing from detergent dispenser.

Secures washer components with a molded sleeve that protects surfaces and reduces vibration. Replace if cracked, worn, or missing to restore secure fit.

Fix a washer that won't spin or agitate with this inverter motor assembly. Resolves LED flashing codes and motor failure. Moderate DIY repair.

This shipping bar assembly secures the oven door and internal components during transport to prevent movement and damage. Replacing a damaged or missing shipping bar helps ensure the range or oven door stays protected while moving the appliance. What it does:

• Holds the oven door and internal parts in place during shipment to reduce jostling and impact
• Prevents door misalignment or damage caused by transit
• Helps avoid rattling or loose parts after relocation
• Used only for transport/protection; remove before regular appliance operation if instructed by manufacturer

• One shipping bar assembly

• Intended for use during shipping/transport — confirm removal instructions in your owner's manual before operating the appliance
• Install or remove with the appliance powered off and according to manufacturer guidance
• Keep small fasteners and clips secure; replace any missing hardware with OEM-specified parts

This push button is the user-facing control button that completes a control circuit when pressed, restoring responsiveness to a worn or broken selector interface. It provides a direct, replaceable way to fix unresponsive or stuck control input. What it does

• Acts as the external control button that engages the appliance's internal switch when pressed
• Restores tactile feedback and reliable control input if the original button is cracked, loose, or missing
• Common symptom fix: buttons that stick, don't depress fully, or fail to activate functions
• Works with the matched internal switch assembly to ensure consistent operation

• Disconnect power before any service
• Remove the control panel or bezel as needed to access the button; avoid prying on surrounding trim
• Replace the button by aligning and snapping it into the button housing; do not force or bend retaining tabs
• If the button does not restore function, inspect the underlying switch/mechanism for damage before ordering additional parts

Snap-in plastic clip cover that conceals fasteners and secures panels on your top-load washer. Replace if broken or missing to restore appearance.

Replaces a worn, cracked, or missing rotary control dial on your washer. Restores clear, tactile control for selecting cycles and settings.

Fix a washer that won't advance through cycles or stops mid-cycle with this timer control. Restores proper wash, rinse, and spin sequencing.

Fix a washer that won't start, has no display, or won't respond to buttons with this control board assembly. Houses cycle selector and display panel.

Washer won't advance through cycles or timer dial doesn't respond? This mechanical timer restores timed operation and reliable cycle progression.

This compressor start relay helps the refrigerator compressor start reliably so the appliance can cool properly. It replaces a failed relay to restore normal compressor startup and reduce hard-start symptoms. What it does:

• Supplies the compressor's start winding with a timed boost to initiate motor start
• Helps prevent repeated clicking or humming when the compressor struggles to start
• Commonly used when the refrigerator is warm, not cooling, or the compressor does not run
• Works with the compressor start circuit as a replacement electrical relay

• Disconnect power to the appliance before accessing the compressor or electrical components
• Replace the relay on the compressor terminal block; ensure firm, correct terminal seating
• Inspect the compressor and start capacitor for related faults while servicing

Shipping bolt kit secures your washer tub during transport or relocation. Replace if bolts are missing, lost, or needed for moving your machine safely.

A single replacement screw used to secure appliance panels, trim, and internal brackets so components stay aligned and reduce rattling. Simple, direct-fit fastener for restoring proper mounting and stable operation. What it does:

• Secures panels, mounting brackets, trim pieces and other appliance components
• Helps stop rattling, vibration, or loose panels caused by missing or stripped fasteners
• Restores proper alignment of doors and access panels when original screw is lost or damaged
• Matches the OEM fastening point for a straightforward hardware replacement

• Disconnect power to the appliance before working on electrical components or access panels
• Use the correct screwdriver to avoid stripping the head; match drive type to the screw
• Tighten firmly but do not overtighten—stop when snug to avoid damaging threads or parts
• Keep removed fasteners organized and compare with the replacement to ensure correct fit

Replacement cap for washer softener and bleach dispenser. Seals dispenser opening to prevent spills and contamination. Needed when original cap is cracked or missing.

Protective shield cover that installs inside your washer to guard internal components from heat and debris. Replace if cracked, broken, or missing.

Package of 12