Husqvarna Chainsaw Parts

The thrust screw is made of durable metal and will sit in between a stationary part and a rotating surface within many types of chainsaws. The purpose of the thrust washer is to support the load or motion on a shaft while preventing motion on the shaft. The thrust washer is used to create a surface that supports a bearing where there are moving parts. If the thrust washer becomes damaged or worn, it cannot support the bearings and it may also become damaged. When this occurs, it may cause a rattling or squealing noises. When removing the thrust washer for a replacement, the reel and line assembly needs to be removed. A small screwdriver of a pick can be used to disengage the C-clip so the user can remove the plunger, spring, and thrust washer. Replace the part with a new thrust washer and reassemble the other components.This is an authentic OEM replacement component that is directly sourced from the manufacturer. It is sold as an individual part. The thrust washer is made for use with chainsaws manufactured by Poulan, Poulan Pro, Craftsman, and Husqvarna.

This nut is used to attach a mounting bar to a chainsaw or pole saw. The nut attaches in slightly different ways depending on the product, but it will feed a bolt that attaches the base of the bar to the pole or housing of the saw. If the nut becomes stripped or corroded due to exposure to the elements, it will need to be replaced. A socket wrench and a socket set are needed to install the part. simply screw it into the chain bar studs, making this a quick and easy replacement. The flat side of the nut should face outward to create a flush effect with the rest of the handle. The other side will fit into the bar. This part sold independently. It works with both Poulan and Husqvarna products and is a genuine OEM product sourced directly from the manufacturers.

This is a clip that is used as a fastener in several types of lawn and garden equipment. Unlike nuts and screws with threads, the clip has prongs that attach to the threads of screws and bolts to offer better stability. When the clip is tightened, it acts as a locking mechanism to keep other parts in place. This allows the use of a nut without utilizing a lock washer. These clips can become damaged, brittle, or even break and will need to be replaced. Take a screwdriver and pull up the pins on the clip, which will result in feeling less tension around the component. At this point, the clip can be removed and a new one can be placed in the same position. Press the clip onto the nut or screw and push the pins into place. The rest of the machine can be reassembled and used as normal.This clip is a genuine OEM replacement part that is sourced directly from the manufacturer. The component is sold individually. It is compatible with string trimmers, chainsaws, and edgers manufactured by Poulan, Poulan Pro, Craftsman, Husqvarna, and Weed Eater.

This part is a screw. This is a genuine Husqvarna replacement screw and has been sourced directly from the manufacturer. This replacement part is intended to replace missing or broken screws in a number of different small outdoor power equipment models.With regular usage, screws can easily become stripped, rusted, or lost. This can lead to improper functionality of outdoor power equipment. It's important to use genuine manufacturer replacement screws to ensure the highest-quality materials and a proper fit that will keep equipment in good working order. When installing screws, always follow proper guidelines and abide by appropriate safety measures. Husqvarna screws are manufactured from high-quality, durable material. This replacement part is a high-quality piece of standard hardware with many different applications. For proper installation and usage guidance, it is recommended to refer to the equipment manufacturer diagram.This replacement screw is designed to fit various models of Husqvarna, Craftsman, Poulan, and Weed Eater trimmers and hedge trimmers, blowers, and chainsaws. Please note this screw is a genuine OEM part and is sold individually.

This nut is most commonly used with gas-powered chainsaws. The nut is used with a bolt, which is sold separately, to secure the carburetor and air filter together. It is a fastener that comes with a threaded hole. The bolt helps fight against rotation and vibrations that can pull the nut loose.Nuts can experience wear and tear and may become damaged or broken over time. If the nut has broken in half, has significant damage, or has been exposed to corrosive materials, it will need to be replaced. A wrench can be used to remove the damaged nut. Once that nut is removed, the new replacement part can be installed. Make sure to use work gloves and tighten the nut before using the lawn and garden equipment in the future.This is a genuine replacement part that is directly sourced from the manufacturer. It can be used with a variety of chainsaws, string trimmers, edgers, hedge trimmers, leaf blowers, and brush cutters created by Poulan, Poulan Pro, Craftsman, and Husqvarna. It is sold as an individual component. This part is sold individually.

This is a replacement screw for chainsaws. This screw attaches the cylinder shield to the main body of the chainsaw. Over time and with regular use, the screw can become loose or damaged. This causes the cylinder shield to become loose as well, which could lead to the entire chainsaw falling apart during use. A loose cylinder shield exposes the engine to the elements and can cause damage to the engine and the chainsaw's performance.Check the screw to see if it should be replaced by trying to move the cylinder shield. If it stays firm, then the screw is fine. If you feel any looseness or resistance, the screw will need to be replaced as soon as possible. Check the screws for wear and tear frequently.This is a genuine OEM part sourced from the manufacturer, and it is a size T-25 Torx screw. The screw can be installed with a screwdriver, and the installation process should not take too long. Remember to always be careful around a chainsaw's blade, even for this simple repair.

This knob is a genuine Husqvarna part. It is for use on a blower. The most common reason that a knob will need to be replaced is that the screw has been stripped from force or repeated use. The plastic knob handle may also become worn or damaged over time.Replacing this knob is very simple, but some safety precautions are necessary. Be sure to remove the wire and boot from the spark plug to prevent the appliance from starting accidentally. Be sure the fuel tank is empty. This knob is a genuine OEM part sourced directly from the manufacturer. This knob is compatible with several models of blowers, including Husqvarna, Poulan, and Weedeater. It may be compatible with blowers manufactured by AYP, Craftsman, Jonsered, McCulloch, and RedMax. Use the compatibility checker to find out. It also replaces obsolete part number 530049485.

This screw is designed to be used in many different chainsaws to connect and hold together various components. The screw can be used on its own or placed with a nut in a pre-drilled and threaded hole. If a nut is going to be used, it is best to choose one with the same threading and finish as the screw that will be used. A screw can become damaged in many ways that will require a replacement. Corrosion, excessive stress, or high temperatures may weaken the screw. In some cases, the damage can cause it to break or become loose and no longer properly secure other components of the chainsaw. A visual inspection can help determine if corrosion is present or the screw is damaged or broken. If the screw is stripped, a bolt remover may be needed to remove it to make the replacement.This screw is a genuine OEM replacement part provided directly from the manufacturer. It is sold as an individual component. The screw is compatible with chainsaws created by Poulan, Poulan Pro, Craftsman, and Husqvarna. A screwdriver is needed to replace, remove, or install the replacement part.

This is an OEM replacement screw that is specifically designed to secure the fuel tank on select lawn and garden equipment. The fuel tank retainer screw is made of durable metal and will be screwed to the fuel tank and the body of the machine, holding the tank in place and preventing it from being exposed to excessive vibrations or potential spillage. These screws can become worn over time or be lost in the process of other repairs. This genuine OEM fuel tank retainer screw is compatible with hundreds of trimmers, blowers, edgers, and pruners. It can be used with select models of machines from Poulan, Husqvarna, Weed Eater, and Jonsered. Owners should check their parts diagram for exact placement and part number compatibility as fuel tank retainer screws come in different lengths and diameters, so they are model-specific. This screw is made of durable metal and will require a Torx driver to install. The fuel tank retainer screw includes a built-in washer and is sold as an individual unit. Those who need more than one will have to purchase multiple quantities.

This screw is designed to be used with a range of handheld land and garden tools. The screw is a common piece of hardware used to fasten various parts of equipment and machines. Screws can be used for a range of applications depending on the equipment.Screws are meant to last, but they can wear down over time. The threads of the screws may become damaged or worn away. The screw could break or become corroded. When working on the machines, it is also possible for the screws to become lost. Having extra on hand can be a good idea. Replacing the screw is a simple project.This screw is intended for use with blowers, edgers, gas trimmers, and other trimmers. It is compatible with models from a variety of brands including Poulan, Husqvarna, Weed Eater, and Jonsered. Each screw is sold individually. This is a genuine OEM replacement screw that has been sourced from the manufacturer.

The carburetor gasket helps to form a seal between the carburetor and the carburetor adapter. It will ensure there are no leaks and that air does not pass through the connection. If there are performance issues or leakage near the carburetor, the culprit could be the carburetor gasket. Additionally, whenever a carburetor is replaced, this gasket must also be replaced. This is because there is a chance that a reused gasket will not reseal properly. If the reused gasket or the new gasket is not installed and seated properly, there is a chance that it could let dirt into the engine. It could also let in extra air, which could lead to damage to the engine. It is important to properly maintain a chainsaw and to replace O-rings and gaskets whenever they show signs of wear and tear. This OEM part will work with a range of models, including Craftsman, Husqvarna, Poulan, and Poulan Pro. This is sold as an individual replacement part.