Parts for Ge PCG23YESAFBB: 06 - Ice Maker & Dispenser Parts

This is a replacement #8-18 machine screw used to secure internal and external appliance components. It provides a simple, reliable fastener option to restore proper fit and reduce rattling or loose panels. What it does

• Fastens control panels, brackets, or chassis components to maintain proper alignment
• Helps stop vibrations and rattling caused by loose hardware
• Restores a missing or damaged screw to prevent parts from shifting during operation
• Works where a #8-18 machine-thread screw is specified by the manufacturer

• One replacement #8-18 screw

• Disconnect power to the appliance before starting any work
• Use the correct screwdriver or nut driver to avoid stripping the head
• Thread by hand to start, then tighten snugly—do not overtighten to avoid cracking plastic or stripping threads

Mounting screw for refrigerator interior components like fan brackets, ice maker assemblies, and shelving. Replace if stripped, missing, or corroded.

Front mounting grommet for refrigerator ice makers. Secures ice maker assembly to freezer wall. Replace if cracked, missing, or worn to restore stability.

Rubber grommet secures the base grille on your refrigerator. Replace if cracked, worn, or missing to restore a snug fit and reduce vibration or rattle.

Replaces a cracked, severed, or frozen ice maker fill tube and grommet. Delivers water from valve to ice maker. Includes tube, grommet, and plate.

Secures the auger shaft in the icemaker assembly. Replace if stripped, cracked, or loose, preventing proper ice transport from bin to dispenser.

Includes 12 retainer rings.

Protective enclosure for the ice crusher mechanism in your refrigerator's dispenser. Replace if cracked, broken, or damaged from ice jams or wear.

Includes 12 washers.

Replacement pivot that supports and aligns refrigerator doors or drawers. Needed when original pivot is cracked, broken, or worn, causing misalignment.

Ice scattering everywhere? This deflector guides cubes or crushed ice down the chute into your glass. Replaces cracked or missing deflectors in 30 minutes.

Ice won't crush in your refrigerator? These auger blades move ice through the crushing mechanism. Common fix when crushed ice dispenses as cubes.

Mounting spacer maintains proper clearance between refrigerator panels, doors, or components. Replace if cracked, broken, or missing to restore fit.

Washer for refrigerator crusher blade assembly. Replaces cracked, worn, or missing washers in ice dispenser mechanism. Restores secure mounting.

Ice dispenser not working or crushed ice won't dispense? This crusher cover protects the ice crushing mechanism. Easy DIY repair with step-by-step video.

Ice dispensing slowly or not at all? A worn ice bucket auger often causes poor dispensing. This helical drive moves cubes to your dispenser or crusher.

Replace a cracked or damaged dispenser bucket with this direct-fit ice bucket to restore reliable ice storage and dispensing. Fits refrigerators with a top-mounted ice dispenser and holds the ice used by the dispenser assembly. What it does:

• Holds and guides cubed or crushed ice from the freezer storage to the dispenser
• Ensures proper alignment for the dispenser auger and chute to reduce jams
• Prevents ice from spilling into the freezer compartment
• Helps maintain consistent ice flow to the dispenser chute

• Disconnect power to the refrigerator before service to avoid injury
• Remove all ice from the bucket before uninstalling or installing
• Handle gently to avoid cracking the new bucket; avoid overtightening fasteners
• Check orientation and engagement with the auger/dispenser mechanism during reassembly

Ice bucket and auger assembly for refrigerator ice dispensers. Replaces cracked, broken, or worn ice storage bin. Includes auger mechanism for ice delivery.

Replaces a cracked, broken, or missing right-side glide bucket on your refrigerator door. Secures storage bins and allows smooth sliding on the rail.

The Glide Bracket is an OEM part for GE refrigerators. This left bracket supports the refrigerator drawer, allowing it to slide in and out smoothly for easy access to stored items.

Causes of a bad glide bracket can include regular wear and tear, damage from overloading the drawer, or accidental impact that causes the bracket to crack or break.

Symptoms of a bad glide bracket include:

• Difficulty sliding the drawer in and out
• The drawer not aligning properly or coming off its tracks
• Unusual noises when opening or closing the drawer
• Visible cracks or breaks in the bracket

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Angle bracket for refrigerators. Installs to support shelves, drawers, or interior panels. Replace if bent, cracked, broken, or missing hardware.

Ice won't dispense or auger spins freely? The drive coupler connects the motor to the auger. Moderately easy DIY repair with pliers and patience.

Mounting screw fastens panels, brackets, and trim in refrigerators, dishwashers, and ranges. Replace missing, stripped, or rusty screws to secure parts.

Fix ice dispenser not crushing or dispensing ice with this refrigerator ice crusher motor. Direct replacement for GE and other brands. Moderate DIY repair.

10-18 hex washer screw for securing panels, trim, brackets, and components in appliances. Replaces lost, stripped, or corroded fasteners.

Wire harness assembly that connects the motor and solenoid in your refrigerator. Replace if wires are frayed, connectors are damaged, or harness is broken.

This solenoid saddle is a small mounting bracket that secures a refrigerator solenoid in the correct position. By preventing movement and misalignment, it helps the linked mechanism engage smoothly and consistently.

• Secures the solenoid to its housing or frame to prevent shifting
• Maintains proper alignment for reliable actuation
• A worn or broken saddle can cause buzzing/chattering and intermittent operation
• Restores stable mounting to help the connected mechanism work correctly

• Disconnect power; shut off water supply if working near water lines
• Access the solenoid assembly and note the original saddle's orientation
• Transfer the solenoid into the new saddle and reuse existing fasteners/clips
• Smooth operation before reassembling panels

Fix a refrigerator that won't dispense water or make ice with this water inlet valve solenoid assembly. Direct replacement part for select models.

This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.

• Converts the solenoid's electrical action into mechanical movement for the dispenser ice chute door
• Helps maintain a proper seal to limit frost and moisture around the dispenser
• Typical symptoms: ice won't dispense; chute door won't open/close; frost/ice buildup at the chute; loud buzzing or clicking from the dispenser area
• Wear or sticking of the armature/spring can hinder movement and affect dispenser operation

• Unplug the refrigerator and shut off water to the dispenser before servicing
• Access the dispenser mechanism in the door; remove trim/control panel per your model's service information
• Note the orientation of the armature, spring, and linkage; transfer components one-for-one to the new kit and secure hardware
• Verify the solenoid plunger moves freely, reassemble, restore power, and test dispenser operation

This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.

• Converts the solenoid's electrical action into mechanical movement for the dispenser ice chute door
• Helps maintain a proper seal to limit frost and moisture around the dispenser
• Typical symptoms: ice won't dispense; chute door won't open/close; frost/ice buildup at the chute; loud buzzing or clicking from the dispenser area
• Wear or sticking of the armature/spring can hinder movement and affect dispenser operation

• Unplug the refrigerator and shut off water to the dispenser before servicing
• Access the dispenser mechanism in the door; remove trim/control panel per your model's service information
• Note the orientation of the armature, spring, and linkage; transfer components one-for-one to the new kit and secure hardware
• Verify the solenoid plunger moves freely, reassemble, restore power, and test dispenser operation

This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.

• Converts the solenoid's electrical action into mechanical movement for the dispenser ice chute door
• Helps maintain a proper seal to limit frost and moisture around the dispenser
• Typical symptoms: ice won't dispense; chute door won't open/close; frost/ice buildup at the chute; loud buzzing or clicking from the dispenser area
• Wear or sticking of the armature/spring can hinder movement and affect dispenser operation

• Unplug the refrigerator and shut off water to the dispenser before servicing
• Access the dispenser mechanism in the door; remove trim/control panel per your model's service information
• Note the orientation of the armature, spring, and linkage; transfer components one-for-one to the new kit and secure hardware
• Verify the solenoid plunger moves freely, reassemble, restore power, and test dispenser operation

This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.

• Converts the solenoid's electrical action into mechanical movement for the dispenser ice chute door
• Helps maintain a proper seal to limit frost and moisture around the dispenser
• Typical symptoms: ice won't dispense; chute door won't open/close; frost/ice buildup at the chute; loud buzzing or clicking from the dispenser area
• Wear or sticking of the armature/spring can hinder movement and affect dispenser operation

• Unplug the refrigerator and shut off water to the dispenser before servicing
• Access the dispenser mechanism in the door; remove trim/control panel per your model's service information
• Note the orientation of the armature, spring, and linkage; transfer components one-for-one to the new kit and secure hardware
• Verify the solenoid plunger moves freely, reassemble, restore power, and test dispenser operation

Ice dispenser only making crushed ice instead of cubes? This solenoid valve kit fixes the cube/crushed ice selector. Easy DIY repair with video guide.

This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.

• Converts the solenoid's electrical action into mechanical movement for the dispenser ice chute door
• Helps maintain a proper seal to limit frost and moisture around the dispenser
• Typical symptoms: ice won't dispense; chute door won't open/close; frost/ice buildup at the chute; loud buzzing or clicking from the dispenser area
• Wear or sticking of the armature/spring can hinder movement and affect dispenser operation

• Unplug the refrigerator and shut off water to the dispenser before servicing
• Access the dispenser mechanism in the door; remove trim/control panel per your model's service information
• Note the orientation of the armature, spring, and linkage; transfer components one-for-one to the new kit and secure hardware
• Verify the solenoid plunger moves freely, reassemble, restore power, and test dispenser operation

This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.

• Converts the solenoid's electrical action into mechanical movement for the dispenser ice chute door
• Helps maintain a proper seal to limit frost and moisture around the dispenser
• Typical symptoms: ice won't dispense; chute door won't open/close; frost/ice buildup at the chute; loud buzzing or clicking from the dispenser area
• Wear or sticking of the armature/spring can hinder movement and affect dispenser operation

• Unplug the refrigerator and shut off water to the dispenser before servicing
• Access the dispenser mechanism in the door; remove trim/control panel per your model's service information
• Note the orientation of the armature, spring, and linkage; transfer components one-for-one to the new kit and secure hardware
• Verify the solenoid plunger moves freely, reassemble, restore power, and test dispenser operation

Replaces a cracked or broken ice auger motor boot housing in your refrigerator's dispenser. Installs inside the ice bin to enclose the auger motor assembly.

Replaces damaged or cracked trim over your refrigerator dispenser. Restores clean appearance and hides internal components. Direct fit for dispenser opening.

This is a 220v international model icemaker.

Channels water from the fill tube into the icemaker mold. Replace if cracked, broken, or dislodged, causing water leakage or ice buildup in freezer.